Hello,
I've been using a DWL-G520 as an access point with OpenBSD 3.7. Apart
from not allowing higher modes than 11b, it ran fine.
Today I upgraded to 3.8 form a snapshot I downloaded Friday. The
upgrade went smooth as usual. I went to modify
/usr/src/sys/dev/ic/ar5xxx.c so the country code is set:
/*
* Enable to overwrite the country code (use "00" for debug)
*/
#if 0
#define COUNTRYCODE "fr"
#endif
I compiled the kernel, rebooted but the card was still displaying 'no
regdomain'.
In doubt, I tried to boot on the original kernel, but no luck too.
Is there something new about that?
Below's my dmesg:
OpenBSD 3.8 (GENERIC) #0: Mon Sep 12 20:23:33 CEST 2005
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: AMD Duron(tm) Processor ("AuthenticAMD" 686-class, 64KB L2 cache) 700 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR
real mem = 1073258496 (1048104K)
avail mem = 972722176 (949924K)
using 4278 buffers containing 53764096 bytes (52504K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 07/04/01, BIOS32 rev. 0 @ 0xfdb30
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
apm0: flags 30102 dobusy 0 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf7df0/192 (10 entries)
pcibios0: PCI Interrupt Router at 000:17:0 ("VIA VT8366 ISA" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0xc000 0xcc000/0x4800 0xd0800/0x3800
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "VIA VT8366 PCI" rev 0x00
ppb0 at pci0 dev 1 function 0 "VIA VT8366 AGP" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "Nvidia GeForce2 GTS" rev 0xa4
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
fxp0 at pci0 dev 6 function 0 "Intel 82557" rev 0x05, i82558: irq 12,
address 00:90:27:5c:ce:42
inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 0
ahc1 at pci0 dev 7 function 0 "Adaptec AHA-2940U" rev 0x01: irq 10
scsibus0 at ahc1: 16 targets
sd0 at scsibus0 targ 1 lun 0: <IBM, DNES-309170W, SAH0> SCSI3 0/direct fixed
sd0: 8748MB, 11474 cyl, 5 head, 312 sec, 512 bytes/sec, 17916240 sec total
ath0 at pci0 dev 9 function 0 "Atheros AR5212" rev 0x01: irq 11
ath0: AR5212 5.9 phy 4.3 rf2112 4.6ath0: no valid channels for
regdomain NONE(32976)
pcib0 at pci0 dev 17 function 0 "VIA VT8366 ISA" rev 0x00
pciide0 at pci0 dev 17 function 1 "VIA VT82C571 IDE" rev 0x06: ATA100,
channel 0 configured to compatibility, channel 1 configured to
compatibility
wd0 at pciide0 channel 0 drive 0: <IC35L060AVV207-0>
wd0: 16-sector PIO, LBA48, 58644MB, 120103200 sectors
wd1 at pciide0 channel 0 drive 1: <IC35L040AVVN07-0>
wd1: 16-sector PIO, LBA, 39266MB, 80418240 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 5
atapiscsi0 at pciide0 channel 1 drive 0
scsibus1 at atapiscsi0: 2 targets
cd0 at scsibus1 targ 0 lun 0: <Memorex, DVD-MAXX 1648 AJ, GWH2> SCSI0
5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
uhci0 at pci0 dev 17 function 2 "VIA VT83C572 USB" rev 0x18: irq 5
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: VIA UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 17 function 3 "VIA VT83C572 USB" rev 0x18: irq 5
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: VIA UHCI root hub, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 17 function 4 "VIA VT83C572 USB" rev 0x18: irq 5
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: VIA UHCI root hub, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
lm0 at isa0 port 0x290/8: W83627HF
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask ef65 netmask ff65 ttymask ffe7
pctr: user-level cycle counter enabled
mtrr: Pentium Pro MTRR support
ugen0 at uhub1 port 2
ugen0: Genesys Logic USB Host To Host Bridge, rev 1.00/1.80, addr 2
ahc1: target 1 using 16bit transfers
ahc1: target 1 synchronous at 20.0MHz, offset = 0x8
dkcsum: sd0 matches BIOS drive 0x80
dkcsum: wd0 matches BIOS drive 0x81
dkcsum: wd1 matches BIOS drive 0x82
root on sd0a
rootdev=0x400 rrootdev=0xd00 rawdev=0xd02
