Hello All, and thank you for the assistance.
I was able to boot from CD37.iso, lastest snapshot in serial console but run
into missing init while boot processing.
Here is the output. Any assistance on getting this running again is
appreciated.
Script started on Wed Aug 10 10:50:38 2005
openbsd37# cu -l tty00
Connected
Running power-on diagnostics...
System Maintenance Menu
1) Start System
2) Install System Software
3) Run Diagnostics
4) Recover System
5) Enter Command Monitor
Option? 5
Command Monitor. Type "exit" to return to the menu.
printenv
diskless=0
dbaud=9600
volume=80
sgilogo=y
monitor=h
TimeZone=PST8PDT
netaddr=192.0.2.1
SystemPartition=pci(0)scsi(0)disk(1)rdisk(0)partition(8)
AutoLoad=No
console=d
ConsoleOut=serial(0)
ConsoleIn=serial(0)
cpufreq=180
eaddr=08:00:69:02:df:19
OSLoadPartition=pci(0)scsi(0)disk(1)rdisk(0)partition(0)
OSLoadFilename=/bsd
OSLoader=sash
hinv
System: IP32
Processor: 180 Mhz R5000, with FPU
Primary I-cache size: 32 Kbytes
Primary D-cache size: 32 Kbytes
Secondary cache size: 512 Kbytes
Memory size: 128 Mbytes
Graphics: CRM, Rev C
Audio: A3 version 1
SCSI Disk: scsi(0)disk(1)
SCSI CDROM: scsi(0)cdrom(4)
boot -f dksc(0,4,8)boot
34192+1264 entry: 0x80010120
SystemPartition pci(0)scsi(0)disk(1)rdisk(0)partition(8)
arg 0: dksc(0,4,8)boot
arg 1: ConsoleIn=serial(0)
arg 2: ConsoleOut=serial(0)
arg 3: SystemPartition=pci(0)scsi(0)disk(1)rdisk(0)partition(8)
arg 4: OSLoader=sash
arg 5: OSLoadPartition=pci(0)scsi(0)disk(1)rdisk(0)partition(0)
arg 6: OSLoadFilename=/bsd
OpenBSD/sgi Arcbios boot
Boot: pci(0)scsi(0)disk(1)rdisk(0)partition(0)/bsd
|/-\|Loading ELF64 file
0xffffffff80100000:0x30e0a0,
/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/Zero
0xffffffff8040e0a0:0x5d2a0, Loading symbol table
-\|/-\|/-\|/-\|/-\Start at 0xffffffff80100000
ARCS32 Firmware Version 1.10
SR=34010080
Found SGI-IP32, setting up.
Initial setup done, switching console.
NOTE: TLB code too large, using trampolines
[ using 263136 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2005 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 3.7 (GENERIC) #89: Sun Mar 20 18:32:30 MST 2005
[EMAIL PROTECTED]:/usr/src/sys/arch/sgi/compile/GENERIC
real mem = 134217728
rsvd mem = 7020544
avail mem = 108883968
using 1638 buffers containing 6709248 bytes of memory
mainbus0 (root)
cpu0 at mainbus0: MIPS R5000 CPU rev 2.1 180 MHz with R5000 based FPC rev
1.0
cpu0: cache L1-I 32KB D 32KB 2 way, L2 512KB direct
macebus0 at mainbus0: crime rev 10.1
clock0 at macebus0: TOD with DS1687, ticker on int5 using count register.
macepcibr0 at macebus0: mace rev 1, host system O2
pci0 at macepcibr0 bus 0
ahc0 at pci0 dev 1 function 0 "Adaptec AIC-7880" rev 0x00: irq 9
ahc0: Host Adapter Bios disabled. Using default SCSI device parameters
scsibus0 at ahc0: 16 targets
ahc0: target 1 using 8bit transfers
ahc0: target 1 using asynchronous transfers
sd0 at scsibus0 targ 1 lun 0: <IBM, DNES-309170Y, SA30> SCSI3 0/direct fixed
sd0: 8748MB, 11474 cyl, 5 head, 312 sec, 512 bytes/sec, 17916240 sec total
cd0 at scsibus0 targ 4 lun 0: <TOSHIBA, CD-ROM XM-5701TA, 0167> SCSI2
5/cdrom
removable
ahc1 at pci0 dev 2 function 0 "Adaptec AIC-7880" rev 0x00: irq 10
ahc1: Host Adapter Bios disabled. Using default SCSI device parameters
scsibus1 at ahc1: 16 targets
com0 at macebus0: ns16550a, 16 byte fifo
com0: console
com1 at macebus0: ns16550a, 16 byte fifo
mec0 at macebus0: MAC-110 rev 1, address 08:00:69:02:df:19
nsphy0 at mec0 phy 8: DP83840 10/100 PHY, rev. 1
mavb0 at macebus0: AD1843 rev 1
audio0 at mavb0
boot device: sd0.
root device (default sd0a):
swap device (default sd0b):
root on sd0a
ahc0: target 1 using 16bit transfers
ahc0: target 1 synchronous at 10.0MHz, offset = 0x8
rootdev=0x0 rrootdev=0x900 rawdev=0x902
warning: /dev/console does not exist
init: not found
panic: no init
Stopped at Debugger+0x4: jr ra
nop
RUN AT LEAST 'trace' AND 'ps' AND INCLUDE OUTPUT WHEN REPORTING THIS PANIC!
DO NOT EVEN BOTHER REPORTING THIS WITHOUT INCLUDING THAT INFORMATION!
ddb> trce ace
Debugger+0x4 (ffffffffffffffff,ffffffffffffffff,500,d) sp ffffffffc6a93eb0
ra f
fffffff801b7d58, sz 0
panic+0xe0 (ffffffffffffffff,ffffffffffffffff,500,d) sp ffffffffc6a93eb0 ra
fff
fffff801927dc, sz 96
start_init+0x23c (ffffffffffffffff,ffffffffffffffff,500,d) sp
ffffffffc6a93f10 r
a ffffffff803601a8, sz 176
proc_trampoline+0x48 (ffffffffffffffff,ffffffffffffffff,500,d) sp
ffffffffc6a93
fc0 ra 0, sz 0
User-level: pid 1
ddb> ps
PID PPID PGRP UID S FLAGS WAIT COMMAND
8 0 0 0 3 0x100204 crypto_wa crypto
7 0 0 0 3 0x100204 aiodoned aiodoned
6 0 0 0 3 0x100204 syncer update
5 0 0 0 3 0x100204 cleaner cleaner
4 0 0 0 3 0x100204 reaper reaper
3 0 0 0 3 0x100204 pgdaemon pagedaemon
2 0 0 0 3 0x100204 kmalloc kmthread
* 1 0 0 0 7 0x4 swapper
0 -1 0 0 3 0x80204 scheduler swapper
ddb> boot reb halt
System Halt.
Running power-on diagnostics...
System Maintenance Menu
1) Start System
2) Install System Software
3) Run Diagnostics
4) Recover System
5) Enter Command Monitor
Option? 5
Command Monitor. Type "exit" to return to the menu.
boot -f dksc(, 0,4,8)boot c
34192+1264 entry: 0x80010120
SystemPartition pci(0)scsi(0)disk(1)rdisk(0)partition(8)
arg 0: dksc(0,4,8)boot
arg 1: c
arg 2: ConsoleIn=serial(0)
arg 3: ConsoleOut=serial(0)
arg 4: SystemPartition=pci(0)scsi(0)disk(1)rdisk(0)partition(8)
arg 5: OSLoader=sash
arg 6: OSLoadPartition=pci(0)scsi(0)disk(1)rdisk(0)partition(0)
arg 7: OSLoadFilename=/bsd
OpenBSD/sgi Arcbios boot
Boot: pci(0)scsi(0)disk(1)rdisk(0)partition(0)/bsd
|/-\|Loading ELF64 file
0xffffffff80100000:0x30e0a0,
/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/Zero
0xffffffff8040e0a0:0x5d2a0, Loading symbol table
-\|/-\|/-\|/-\|/-\Start at 0xffffffff80100000
ARCS32 Firmware Version 1.10
SR=34010080
Found SGI-IP32, setting up.
Initial setup done, switching console.
NOTE: TLB code too large, using trampolines
[ using 263136 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2005 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 3.7 (GENERIC) #89: Sun Mar 20 18:32:30 MST 2005
[EMAIL PROTECTED]:/usr/src/sys/arch/sgi/compile/GENERIC
real mem = 134217728
rsvd mem = 7020544
avail mem = 108883968
using 1638 buffers containing 6709248 bytes of memory
mainbus0 (root)
cpu0 at mainbus0: MIPS R5000 CPU rev 2.1 180 MHz with R5000 based FPC rev
1.0
cpu0: cache L1-I 32KB D 32KB 2 way, L2 512KB direct
macebus0 at mainbus0: crime rev 10.1
clock0 at macebus0: TOD with DS1687, ticker on int5 using count register.
macepcibr0 at macebus0: mace rev 1, host system O2
pci0 at macepcibr0 bus 0
ahc0 at pci0 dev 1 function 0 "Adaptec AIC-7880" rev 0x00: irq 9
ahc0: Host Adapter Bios disabled. Using default SCSI device parameters
scsibus0 at ahc0: 16 targets
ahc0: target 1 using 8bit transfers
ahc0: target 1 using asynchronous transfers
sd0 at scsibus0 targ 1 lun 0: <IBM, DNES-309170Y, SA30> SCSI3 0/direct fixed
sd0: 8748MB, 11474 cyl, 5 head, 312 sec, 512 bytes/sec, 17916240 sec total
cd0 at scsibus0 targ 4 lun 0: <TOSHIBA, CD-ROM XM-5701TA, 0167> SCSI2
5/cdrom
removable
ahc1 at pci0 dev 2 function 0 "Adaptec AIC-7880" rev 0x00: irq 10
ahc1: Host Adapter Bios disabled. Using default SCSI device parameters
scsibus1 at ahc1: 16 targets
com0 at macebus0: ns16550a, 16 byte fifo
com0: console
com1 at macebus0: ns16550a, 16 byte fifo
mec0 at macebus0: MAC-110 rev 1, address 08:00:69:02:df:19
nsphy0 at mec0 phy 8: DP83840 10/100 PHY, rev. 1
mavb0 at macebus0: AD1843 rev 1
audio0 at mavb0
boot device: sd0.
root device (default sd0a):
swap device (default sd0b):
root on sd0a
ahc0: target 1 using 16bit transfers
sd0(ahc0:1:0): SCB 0x1e - timed out
================== Dump Card State Begins =================
ahc0: Dumping Card State in Message-out phase, at SEQADDR 0x16d
Card was paused
ACCUM = 0xa0, SINDEX = 0x61, DINDEX = 0xc0, ARG_2 = 0x7
HCNT = 0x0 SCBPTR = 0x0
SCSISIGI[0xb6] ERROR[0x0] SCSIBUSL[0x1] LASTPHASE[0xa0]
SCSISEQ[0x12] SBLKCTL[0x2] SCSIRATE[0x80] SEQCTL[0x10]
SEQ_FLAGS[0x40] SSTAT0[0x7] SSTAT1[0x3] SSTAT2[0x0]
SSTAT3[0x0] SIMODE0[0x0] SIMODE1[0xac] SXFRCTL0[0x88]
DFCNTRL[0x4] DFSTATUS[0x6d]
STACK: 0xe2 0x0 0x167 0x197
SCB count = 32
Kernel NEXTQSCB = 31
Card NEXTQSCB = 31
QINFIFO entries:
Waiting Queue entries:
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Sequencer SCB Info:
0 SCB_CONTROL[0x60] SCB_SCSIID[0x17]
SCB_LUN[0x0] SCB_TAG[0x1e]
1 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
2 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
3 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
4 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
5 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
6 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
7 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
8 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
9 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
10 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
11 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
12 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
13 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
14 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
15 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
Pending list:
30 SCB_CONTROL[0x60] SCB_SCSIID[0x17]
SCB_LUN[0x0]
Kernel Free SCB list: 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12
11
10 9 8 7 6 5 4 3 2 1 0
FEATURES = 0x10004, FLAGS = 0x8401f44, CHIP = 0x407 BUGS =0x25
================= Dump Card State Ends ==================
sg[0] - Addr 0x907e0000 : Length 128
sd0(ahc0:1:0): BDR message in message buffer
sd0(ahc0:1:0): SCB 0x1e - timed out
================== Dump Card State Begins =================
ahc0: Dumping Card State in Message-out phase, at SEQADDR 0x16d
Card was paused
ACCUM = 0xa0, SINDEX = 0x61, DINDEX = 0xc0, ARG_2 = 0x7
HCNT = 0x0 SCBPTR = 0x0
SCSISIGI[0xb6] ERROR[0x0] SCSIBUSL[0x1] LASTPHASE[0xa0]
SCSISEQ[0x12] SBLKCTL[0x2] SCSIRATE[0x80] SEQCTL[0x10]
SEQ_FLAGS[0x40] SSTAT0[0x7] SSTAT1[0x3] SSTAT2[0x0]
SSTAT3[0x0] SIMODE0[0x0] SIMODE1[0xac] SXFRCTL0[0x88]
DFCNTRL[0x4] DFSTATUS[0x6d]
STACK: 0xe2 0x0 0x167 0x197
SCB count = 32
Kernel NEXTQSCB = 31
Card NEXTQSCB = 31
QINFIFO entries:
Waiting Queue entries:
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Sequencer SCB Info:
0 SCB_CONTROL[0x60] SCB_SCSIID[0x17]
SCB_LUN[0x0] SCB_TAG[0x1e]
1 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
2 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
3 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
4 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
5 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
6 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
7 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
8 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
9 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
10 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
11 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
12 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
13 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
14 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
15 SCB_CONTROL[0x0] SCB_SCSIID[0xff]
SCB_LUN[0xff] SCB_TAG[0xff]
Pending list:
30 SCB_CONTROL[0x60] SCB_SCSIID[0x17]
SCB_LUN[0x0]
Kernel Free SCB list: 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12
11
10 9 8 7 6 5 4 3 2 1 0
FEATURES = 0x10004, FLAGS = 0x8401f44, CHIP = 0x407 BUGS =0x25
================= Dump Card State Ends ==================
sg[0] - Addr 0x907e0000 : Length 128
sd0(ahc0:1:0): no longer in timeout, status = 0
ahc0: target 1 using 8bit transfers
ahc0: target 1 using asynchronous transfers
ahc0: Issued Channel A Bus Reset. 1 SCBs aborted
ahc0: target 1 using 16bit transfers
ahc0: target 1 synchronous at 10.0MHz, offset = 0x8
ahc0: target 1 using 16bit transfers
ahc0: target 1 synchronous at 10.0MHz, offset = 0x8
rootdev=0x0 rrootdev=0x900 rawdev=0x902
warning: /dev/console does not exist
init: not found
panic: no init
Stopped at Debugger+0x4: jr ra
nop
RUN AT LEAST 'trace' AND 'ps' AND INCLUDE OUTPUT WHEN REPORTING THIS PANIC!
DO NOT EVEN BOTHER REPORTING THIS WITHOUT INCLUDING THAT INFORMATION!
ddb> trace
Debugger+0x4 (ffffffffffffffff,ffffffffffffffff,500,d) sp ffffffffc6a93eb0
ra f
fffffff801b7d58, sz 0
panic+0xe0 (ffffffffffffffff,ffffffffffffffff,500,d) sp ffffffffc6a93eb0 ra
fff
fffff801927dc, sz 96
start_init+0x23c (ffffffffffffffff,ffffffffffffffff,500,d) sp
ffffffffc6a93f10 r
a ffffffff803601a8, sz 176
proc_trampoline+0x48 (ffffffffffffffff,ffffffffffffffff,500,d) sp
ffffffffc6a93
fc0 ra 0, sz 0
User-level: pid 1
ddb> b ps
PID PPID PGRP UID S FLAGS WAIT COMMAND
8 0 0 0 3 0x100204 crypto_wa crypto
7 0 0 0 3 0x100204 aiodoned aiodoned
6 0 0 0 3 0x100204 syncer update
5 0 0 0 3 0x100204 cleaner cleaner
4 0 0 0 3 0x100204 reaper reaper
3 0 0 0 3 0x100204 pgdaemon pagedaemon
2 0 0 0 3 0x100204 kmalloc kmthread
* 1 0 0 0 7 0x4 swapper
0 -1 0 0 3 0x80204 scheduler swapper
ddb> boot halt
System Halt.
From: Per Fogelstrvm <[EMAIL PROTECTED]>
To: Ober Heim <[EMAIL PROTECTED]>
CC: misc@openbsd.org
Subject: Re: sgi 02 latest snapshot CD37.iso boot problems
Date: Wed, 10 Aug 2005 16:56:31 +0200
On Wednesday 10 August 2005 16.54, Ober Heim wrote:
> Yeah and when said docs say "refer to the bootpd(8)" man page which no
> longer exists that can cause frustration. :D
>
Really? It also referes to the dhcpd(8) man page and what you need exactly
depends on what type of system you are going to use as your bootp/dhcp
server.
---quote---
First, a bootp or dhcpd server needs to be set up. The bootpd(8) or
dhcpd(8) manual page on your server should provide detailed information
on how to set up the server.
---end quote--
But of course...
P.
> "I am not your puppet. Since when? Now, get your spongy pink ass out
> there, and dance for the cameras." -Death to Smoochy
>
> On Wed, 10 Aug 2005, Per [iso-8859-1] Fogelstrvm wrote:
>
> > Date: Wed, 10 Aug 2005 16:21:05 +0200
> > From: "Per [iso-8859-1] Fogelstrvm" <[EMAIL PROTECTED]>
> > To: misc@openbsd.org
> > Subject: Re: sgi 02 latest snapshot CD37.iso boot problems
> >
> > On Wednesday 10 August 2005 10.18, you wrote:
> >> The fix for me was to not use graphical console.
> >>
> >
> > Well, the install doc pretty much says "serial console", doesn't it?
> >
> > ----
> > Switching from serial to graphics console and vice versa:
> >
> > Booting the ramdisk kernel can be done from the ARCS graphic
console
> > although it might be more convenient to use the serial console
since
> > the kernel currently only supports the serial console. Some systems
> > come with the serial console enabled by default but sometimes
> > this must be changed.
> >
> > To change to serial console, go into the ARCS Maintenance Console
> > and change the ``console'' environment variable, and power-cycle
> > the machine.
> >
> > > setenv console d
> >
> > will select 9600 8N1, no flow control, serial console on the first
> > serial port (labeled ``(1)''), while
> >
> > > setenv console g
> > -----
> >
> > People put a lot of effort into writing these documents to make
setting
> > up an OpenBSD system an easy task...
> >
> > The reason you can see the output until the "Setting up"
> > is that this is the point where OpenBSD switches from the
> > ARCBios console to its own console driver.
> >
> > P.
> >
> >> "I am not your puppet. Since when? Now, get your spongy pink ass out
> >> there, and dance for the cameras." -Death to Smoochy
> >>
> >> On Wed, 10 Aug 2005, Ober Heim wrote:
> >>
> >>> Date: Wed, 10 Aug 2005 02:25:13 -0500 (CDT)
> >>> From: Ober Heim <[EMAIL PROTECTED]>
> >>> To: mrservices <[EMAIL PROTECTED]>
> >>> Cc: misc@openbsd.org
> >>> Subject: Re: sgi 02 latest snapshot CD37.iso boot problems
> >>>
> >>> I never been able to boot a single bsd.rd for as long as sgi has
been
> >>> "supported". It tftps fine, but just like your cd error hangs at the
"Setting
> >>> up" portion of the boot you reference.
> >>> 3.7 fails as does the snapshot.
> >>> I also get the same error on latest cd37.iso and cd38.iso
> >>>
> >>> "I am not your puppet. Since when? Now, get your spongy pink ass out
there,
> >>> and dance for the cameras." -Death to Smoochy
> >>>
> >>> On Tue, 9 Aug 2005, mrservices wrote:
> >>>
> >>>> Date: Tue, 09 Aug 2005 16:34:10 -0700
> >>>> From: mrservices <[EMAIL PROTECTED]>
> >>>> To: misc@openbsd.org
> >>>> Subject: sgi 02 latest snapshot CD37.iso boot problems
> >>>>
> >>>> Hello List,
> >>>>
> >>>> I was able to install OpenBSD on an sgi 02 R5000 but corrupted bsd
when the
> >>>> ftp stalled on download
> >>>> I am unable to boot back into the system trying boot or /bsd or
/bsd.rd
> >>>> with the latest sgi snapshot CD37.iso
> >>>>
> >>>> The system freezes at this point and I have to unplug the unit and
plug
> >>>> back in to restart.
> >>>>
> >>>> arg0: dksc(0,4,8)boot
> >>>> arg1: ConsoleIn=Keyboard()
> >>>> arg2: ConsoleVideo=Video()
> >>>> arg3: SystemPartition= pci(0)scsi(0)disk(1)rdisk(0)partition(8)
> >>>> arg4: OSLoader=sash
> >>>> arg5: OSLoadPartition= pci(0)scsi(0)disk(1)rdisk(0)partition(0)
> >>>> arg6: OSLoadFilename=/bsd
> >>>> 34192+1264
> >>>> entry: 0x80010120 SystemPartition
pci(0)scsi(0)disk(1)rdisk(0)partition(8)
> >>>> OpenBSD/sgi Arcbios boot
> >>>> Boot pci(0)scsi(0)disk(1)rdisk(0)partition(0)/bsd
> >>>> Loading ELF64 File
> >>>> 0xffffffff80100000:0x30e0a0, Zero
> >>>> 0xffffffff8040e0a0:0x5d2a0, Loading symbol table
> >>>> Start at 0xffffffff80100000
> >>>> ARC32 Firmware 1.10
> >>>> SR=34010080
> >>>> Found SGI-IP32, Setting Up
> >>>>
> >>>> I have tried unsetenv OSLoader, OSLoadPartition, OSFilename
> >>>>
> >>>> Command menu ls device shows
> >>>>
> >>>> ls pci(0)scsi(0)disk(1)rdisk(0)partition(8)
> >>>> boot
> >>>>
> >>>> I don't have any IRIX tool disks or other disks to work with.
> >>>>
> >>>> Any help on this is much appreciated.
> >>>>
> >>>> Thank you,
> >>>>
> >>>> rogern
http://messenger.msn.click-url.com/go/onm00200471ave/direct/01/
