Hello Mark and List, thank you for the reply and assistance.
I have tried "Booting from CD-ROM installation media" with cd38.iso but the
02 does not recognize the media.
When I go into the maintenance menu and boot -f dksc(0,4,8)boot, it boots to
/bsd but panic at no init
I am going to try to setup a boot net to another openbsd machine. Total
newbie but on the learning curve!
I just had a successful install on a Panasonic Toughbook CF-25, i386 is
newbie able. : )
Thanks again for your help.
Script started on Fri Aug 12 14:54:44 2005
openbsd37# cu -l tty00
Connected
Running power-on diagnostics...
System Maintenance Menu
1) Start System
2) Install System Software
3) Run Diagnostics
4) Recover System
5) Enter Command Monitor
Option? 5
Command Monitor. Type "exit" to return to the menu.
ls dksc(0,4,8)
dksc(0,4,8):
boot
exit
Running power-on diagnostics...
System Maintenance Menu
1) Start System
2) Install System Software
3) Run Diagnostics
4) Recover System
5) Enter Command Monitor
Option? 2
Installing System Software...
Press <Esc> to return to the menu.
1) Remote Tape 2) Remote Directory 3)[Local CD-ROM] X) Local Tape
*a) Local SCSI CD-ROM drive 4
Enter 1-4 to select source type, a to select the source, <esc> to quit,
or <enter> to start: 3
1) Remote Tape 2) Remote Directory 3)[Local CD-ROM] X) Local Tape
*a) Local SCSI CD-ROM drive 4
Enter 1-4 to select source type, a to select the source, <esc> to quit,
or <enter> to start: 3
1) Remote Tape 2) Remote Directory 3)[Local CD-ROM] X) Local Tape
*a) Local SCSI CD-ROM drive 4
Enter 1-4 to select source type, a to select the source, <esc> to quit,
or <enter> to start:
System Maintenance Menu
1) Start System
2) Install System Software
3) Run Diagnostics
4) Recover System
5) Enter Command Monitor
Option? 5
Command Monitor. Type "exit" to return to the menu.
printenv
diskless=0
dbaud=9600
volume=80
sgilogo=y
monitor=h
TimeZone=PST8PDT
netaddr=192.0.2.1
AutoLoad=No
console=d
SystemPartition=pci(0)scsi(0)disk(1)rdisk(0)partition(8)
ConsoleOut=serial(0)
ConsoleIn=serial(0)
cpufreq=180
eaddr=08:00:69:02:df:19
OSLoadPartition=pci(0)scsi(0)disk(1)rdisk(0)partition(0)
OSLoadFilename=/bsd
OSLoader=sash
hinv
System: IP32
Processor: 180 Mhz R5000, with FPU
Primary I-cache size: 32 Kbytes
Primary D-cache size: 32 Kbytes
Secondary cache size: 512 Kbytes
Memory size: 128 Mbytes
Graphics: CRM, Rev C
Audio: A3 version 1
SCSI Disk: scsi(0)disk(1)
SCSI CDROM: scsi(0)cdrom(4)
boot -f dksc(0,4,8)boot
34192+1264 entry: 0x80010120
SystemPartition pci(0)scsi(0)disk(1)rdisk(0)partition(8)
arg 0: dksc(0,4,8)boot
arg 1: ConsoleIn=serial(0)
arg 2: ConsoleOut=serial(0)
arg 3: SystemPartition=pci(0)scsi(0)disk(1)rdisk(0)partition(8)
arg 4: OSLoader=sash
arg 5: OSLoadPartition=pci(0)scsi(0)disk(1)rdisk(0)partition(0)
arg 6: OSLoadFilename=/bsd
OpenBSD/sgi Arcbios boot
Boot: pci(0)scsi(0)disk(1)rdisk(0)partition(0)/bsd
|/-\|Loading ELF64 file
0xffffffff80100000:0x30e0a0, Zero 0xffffffff8040e0a0:0x5d2a0, Loading symbol
table
Start at 0xffffffff80100000
ARCS32 Firmware Version 1.10
SR=34010080
Found SGI-IP32, setting up.
Initial setup done, switching console.
NOTE: TLB code too large, using trampolines
[ using 263136 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2005 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 3.7 (GENERIC) #89: Sun Mar 20 18:32:30 MST 2005
[EMAIL PROTECTED]:/usr/src/sys/arch/sgi/compile/GENERIC
real mem = 134217728
rsvd mem = 7020544
avail mem = 108883968
using 1638 buffers containing 6709248 bytes of memory
mainbus0 (root)
cpu0 at mainbus0: MIPS R5000 CPU rev 2.1 180 MHz with R5000 based FPC rev
1.0
cpu0: cache L1-I 32KB D 32KB 2 way, L2 512KB direct
macebus0 at mainbus0: crime rev 10.1
clock0 at macebus0: TOD with DS1687, ticker on int5 using count register.
macepcibr0 at macebus0: mace rev 1, host system O2
pci0 at macepcibr0 bus 0
ahc0 at pci0 dev 1 function 0 "Adaptec AIC-7880" rev 0x00: irq 9
ahc0: Host Adapter Bios disabled. Using default SCSI device parameters
scsibus0 at ahc0: 16 targets
ahc0: target 1 using 8bit transfers
ahc0: target 1 using asynchronous transfers
sd0 at scsibus0 targ 1 lun 0: <IBM, DNES-309170Y, SA30> SCSI3 0/direct fixed
sd0: 8748MB, 11474 cyl, 5 head, 312 sec, 512 bytes/sec, 17916240 sec total
cd0 at scsibus0 targ 4 lun 0: <TOSHIBA, CD-ROM XM-5701TA, 0167> SCSI2
5/cdrom removable
ahc1 at pci0 dev 2 function 0 "Adaptec AIC-7880" rev 0x00: irq 10
ahc1: Host Adapter Bios disabled. Using default SCSI device parameters
scsibus1 at ahc1: 16 targets
com0 at macebus0: ns16550a, 16 byte fifo
com0: console
com1 at macebus0: ns16550a, 16 byte fifo
mec0 at macebus0: MAC-110 rev 1, address 08:00:69:02:df:19
nsphy0 at mec0 phy 8: DP83840 10/100 PHY, rev. 1
mavb0 at macebus0: AD1843 rev 1
audio0 at mavb0
boot device: sd0.
root device (default sd0a):
swap device (default sd0b):
root on sd0a
ahc0: target 1 using 16bit transfers
ahc0: target 1 synchronous at 10.0MHz, offset = 0x8
rootdev=0x0 rrootdev=0x900 rawdev=0x902
warning: /dev/console does not exist
init: not found
panic: no init
Stopped at Debugger+0x4: jr ra
nop
RUN AT LEAST 'trace' AND 'ps' AND INCLUDE OUTPUT WHEN REPORTING THIS PANIC!
DO NOT EVEN BOTHER REPORTING THIS WITHOUT INCLUDING THAT INFORMATION!
ddb> trace
Debugger+0x4 (ffffffffffffffff,ffffffffffffffff,500,d) sp ffffffffc6a93eb0
ra f
fffffff801b7d58, sz 0
panic+0xe0 (ffffffffffffffff,ffffffffffffffff,500,d) sp ffffffffc6a93eb0 ra
fff
fffff801927dc, sz 96
start_init+0x23c (ffffffffffffffff,ffffffffffffffff,500,d) sp
ffffffffc6a93f10 r
a ffffffff803601a8, sz 176
proc_trampoline+0x48 (ffffffffffffffff,ffffffffffffffff,500,d) sp
ffffffffc6a93
fc0 ra 0, sz 0
User-level: pid 1
ddb> ps
PID PPID PGRP UID S FLAGS WAIT COMMAND
8 0 0 0 3 0x100204 crypto_wa crypto
7 0 0 0 3 0x100204 aiodoned aiodoned
6 0 0 0 3 0x100204 syncer update
5 0 0 0 3 0x100204 cleaner cleaner
4 0 0 0 3 0x100204 reaper reaper
3 0 0 0 3 0x100204 pgdaemon pagedaemon
2 0 0 0 3 0x100204 kmalloc kmthread
* 1 0 0 0 7 0x4 swapper
0 -1 0 0 3 0x80204 scheduler swapper
ddb> dmesg
NOTE: TLB code too large, using trampolines
[ using 263136 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2005 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 3.7 (GENERIC) #89: Sun Mar 20 18:32:30 MST 2005
[EMAIL PROTECTED]:/usr/src/sys/arch/sgi/compile/GENERIC
real mem = 134217728
rsvd mem = 7020544
avail mem = 108883968
using 1638 buffers containing 6709248 bytes of memory
mainbus0 (root)
cpu0 at mainbus0: MIPS R5000 CPU rev 2.1 180 MHz with R5000 based FPC rev
1.0
cpu0: cache L1-I 32KB D 32KB 2 way, L2 512KB direct
macebus0 at mainbus0: crime rev 10.1
clock0 at macebus0: TOD with DS1687, ticker on int5 using count register.
macepcibr0 at macebus0: mace rev 1, host system O2
pci0 at macepcibr0 bus 0
ahc0 at pci0 dev 1 function 0 "Adaptec AIC-7880" rev 0x00: irq 9
ahc0: Host Adapter Bios disabled. Using default SCSI device parameters
scsibus0 at ahc0: 16 targets
--db_more--ahc0: target 1 using 8bit transfers
--db_more--ahc0: target 1 using asynchronous transfers
--db_more--sd0 at scsibus0 targ 1 lun 0: <IBM, DNES-309170Y, SA30> SCSI3
0/direct fixed
--db_more--sd0: 8748MB, 11474 cyl, 5 head, 312 sec, 512 bytes/sec, 17916240
sec total
--db_more--cd0 at scsibus0 targ 4 lun 0: <TOSHIBA, CD-ROM XM-5701TA, 0167>
SCSI2 5/cdrom r
--db_more--removable
--db_more--ahc1 at pci0 dev 2 function 0 "Adaptec AIC-7880" rev 0x00: irq 10
--db_more--ahc1: Host Adapter Bios disabled. Using default SCSI device
parameters
--db_more--scsibus1 at ahc1: 16 targets
--db_more--com0 at macebus0: ns16550a, 16 byte fifo
--db_more--com0: console
--db_more--com1 at macebus0: ns16550a, 16 byte fifo
--db_more--mec0 at macebus0: MAC-110 rev 1, address 08:00:69:02:df:19
--db_more--nsphy0 at mec0 phy 8: DP83840 10/100 PHY, rev. 1
--db_more--mavb0 at macebus0: AD1843 rev 1
--db_more--audio0 at mavb0
--db_more--boot device: sd0.
--db_more--root device (default sd0a):
--db_more--swap device (default sd0b):
--db_more--root on sd0a
--db_more--ahc0: target 1 using 16bit transfers
--db_more--ahc0: target 1 synchronous at 10.0MHz, offset = 0x8
--db_more--rootdev=0x0 rrootdev=0x900 rawdev=0x902
--db_more--warning: /dev/console does not exist
--db_more--init: not found
--db_more--panic: no init
--db_more--Stopped at Debugger+0x4: jr ra
--db_more-- nop
--db_more--R
From: Mark Kettenis <[EMAIL PROTECTED]>
To: misc@openbsd.org
CC: [EMAIL PROTECTED]
Subject: Re: sgi 02 latest snapshot CD37.iso boot problems
Date: Fri, 12 Aug 2005 09:53:49 +0200 (CEST)
Please reread the current INSTALL.sgi again, in particular the section
on "Booting from CD-ROM installation media".
It should no longer be necessary to enter the Command Monitor to boot
from CD-ROM; just choose "Install System Software" from the System
Maintenance Menu.
Mark
_________________________________________________________________
Is your PC infected? Get a FREE online computer virus scan from McAfee.
Security. http://clinic.mcafee.com/clinic/ibuy/campaign.asp?cid=3963
