Hi Peter If you test with load, do you get a steady stream? Did you test in both directions: to and from your box?
I see the same symptoms, but I can provoke them to happen under load. Bizarre is, that sending data from the pfsense box works fine, I see a steady stream of 55-57MB/s. In the opposite direction sending from my host to the pfsense box peaks in 10-25MB/s and drops to zero for some seconds repeatedly. No matter if I use a direct cable or different switches. This happens with two both of my gateways, which are the same ibase fw7404 boxes (embedded systems, not possible to change nics). CPU load is at around 25% only. A different box with the same pfsense version and the same ethernet chip (RTL-8111e Chip rev. 0x2c800000) doesn't show this behavior. I played around with the system tuneables too (switch on and off tso, ...), but with no success. The only suspicious thing I see on the failing box are some of such messages: kernel: pid 37699 (php), uid 0: exited on signal 11 (core dumped) They are not in an obvious relation to an ethernet event. Indeed help would be very much appreciated. Regards, Adrian. Am 07.12.13 19:50 schrieb Peter Merritt: > Randomly, sometimes hours or days apart one of the realtek nics on my > system will stop responding, dropping connection. The error message is > > > > re1: watchdog timeout > > re1: Stopping TXQ timed out. > > > > This has happened on 3 different mother boards now all with realtek > nics. ( hard to find an itx board with another kind of nic) > > > > I does not see to be a load based problem, as I did some testing of the > connection with nc to see if I could make it fail. re0 is not connected > right now. Any help would be greatly appreciated. > > Peter > > > > > > Dmesg follows > > > > Copyright (c) 1992-2012 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD is a registered trademark of The FreeBSD Foundation. > FreeBSD 8.3-RELEASE-p11 #0: Wed Sep 11 18:51:23 EDT 2013 > > root@snapshots-8_3-amd64.builders.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_SMP.8 > amd64 > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: Intel(R) Celeron(R) CPU 1007U @ 1.50GHz (1496.61-MHz K8-class CPU) > Origin = "GenuineIntel" Id = 0x306a9 Family = 6 Model = 3a > Stepping = 9 > > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > > Features2=0x5bae3bf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,TSCDLT,XSAVE> > AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM> > AMD Features2=0x1<LAHF> > TSC: P-state invariant > real memory = 2147483648 (2048 MB) > avail memory = 1904844800 (1816 MB) > ACPI APIC Table: <ALASKA A M I> > FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs > FreeBSD/SMP: 1 package(s) x 2 core(s) > cpu0 (BSP): APIC ID: 0 > cpu1 (AP): APIC ID: 2 > ioapic0 <Version 2.0> irqs 0-23 on motherboard > wlan: mac acl policy registered > ipw_bss: You need to read the LICENSE file in > /usr/share/doc/legal/intel_ipw/. > ipw_bss: If you agree with the license, set > legal.intel_ipw.license_ack=1 in /boot/loader.conf. > module_register_init: MOD_LOAD (ipw_bss_fw, 0xffffffff804a5da0, 0) error 1 > ipw_ibss: You need to read the LICENSE file in > /usr/share/doc/legal/intel_ipw/. > ipw_ibss: If you agree with the license, set > legal.intel_ipw.license_ack=1 in /boot/loader.conf. > module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffffffff804a5e40, 0) error 1 > ipw_monitor: You need to read the LICENSE file in > /usr/share/doc/legal/intel_ipw/. > ipw_monitor: If you agree with the license, set > legal.intel_ipw.license_ack=1 in /boot/loader.conf. > module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffffffff804a5ee0, 0) > error 1 > kbd1 at kbdmux0Copyright (c) 1992-2012 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD is a registered trademark of The FreeBSD Foundation. > FreeBSD 8.3-RELEASE-p11 #0: Wed Sep 11 18:51:23 EDT 2013 > > root@snapshots-8_3-amd64.builders.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_SMP.8 > amd64 > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: Intel(R) Celeron(R) CPU 1007U @ 1.50GHz (1496.61-MHz K8-class CPU) > Origin = "GenuineIntel" Id = 0x306a9 Family = 6 Model = 3a > Stepping = 9 > > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > > Features2=0x5bae3bf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,TSCDLT,XSAVE> > AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM> > AMD Features2=0x1<LAHF> > TSC: P-state invariant > real memory = 2147483648 (2048 MB) > avail memory = 1904844800 (1816 MB) > ACPI APIC Table: <ALASKA A M I> > FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs > FreeBSD/SMP: 1 package(s) x 2 core(s) > cpu0 (BSP): APIC ID: 0 > cpu1 (AP): APIC ID: 2 > ioapic0 <Version 2.0> irqs 0-23 on motherboard > wlan: mac acl policy registered > ipw_bss: You need to read the LICENSE file in > /usr/share/doc/legal/intel_ipw/. > ipw_bss: If you agree with the license, set > legal.intel_ipw.license_ack=1 in /boot/loader.conf. > module_register_init: MOD_LOAD (ipw_bss_fw, 0xffffffff804a5da0, 0) error 1 > ipw_ibss: You need to read the LICENSE file in > /usr/share/doc/legal/intel_ipw/. > ipw_ibss: If you agree with the license, set > legal.intel_ipw.license_ack=1 in /boot/loader.conf. > module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffffffff804a5e40, 0) error 1 > ipw_monitor: You need to read the LICENSE file in > /usr/share/doc/legal/intel_ipw/. > ipw_monitor: If you agree with the license, set > legal.intel_ipw.license_ack=1 in /boot/loader.conf. > module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffffffff804a5ee0, 0) > error 1 > kbd1 at kbdmux0 > cryptosoft0: <software crypto> on motherboard > padlock0: No ACE support. > acpi0: <ALASKA A M I> on motherboard > acpi0: [ITHREAD] > acpi0: Power Button (fixed) > acpi0: reservation of 67, 1 (4) failed > Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 > acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 > cpu0: <ACPI CPU> on acpi0 > cpu1: <ACPI CPU> on acpi0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > vgapci0: <VGA-compatible display> port 0xf000-0xf03f mem > 0xf7800000-0xf7bfffff,0xe0000000-0xefffffff irq 16 at device 2.0 on pci0 > pci0: <simple comms> at device 22.0 (no driver attached) > ehci0: <EHCI (generic) USB 2.0 controller> mem 0xf7d08000-0xf7d083ff irq > 16 at device 26.0 on pci0 > ehci0: [ITHREAD] > usbus0: EHCI version 1.0 > usbus0: <EHCI (generic) USB 2.0 controller> on ehci0 > pci0: <multimedia, HDA> at device 27.0 (no driver attached) > pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0 > pci1: <ACPI PCI bus> on pcib1 > re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F PCIe Gigabit Ethernet> port > 0xe000-0xe0ff mem 0xf7c00000-0xf7c00fff,0xf0100000-0xf0103fff irq 16 at > device 0.0 on pci1 > re0: Using 1 MSI-X message > re0: Chip rev. 0x2c800000 > re0: MAC rev. 0x00000000 > ZFS storage pool version 28 > re0: link state changed to DOWN > re1: link state changed to DOWN > pflog0: promiscuous mode enabled > re1: link state changed to UP > > > > > > > > > [email protected] <- Do not Use > > > miibus0: <MII bus> on re0 > rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus0 > rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, > 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, > 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, > 1000baseT-FDX-flow-master, auto, auto-flow > re0: [ITHREAD] > pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.1 on pci0 > pci2: <ACPI PCI bus> on pcib2 > re1: <RealTek 8168/8111 B/C/CP/D/DP/E/F PCIe Gigabit Ethernet> port > 0xd000-0xd0ff mem 0xf0004000-0xf0004fff,0xf0000000-0xf0003fff irq 17 at > device 0.0 on pci2 > re1: Using 1 MSI-X message > re1: Chip rev. 0x2c800000 > re1: MAC rev. 0x00000000 > miibus1: <MII bus> on re1 > rgephy1: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus1 > rgephy1: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, > 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, > 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, > 1000baseT-FDX-flow-master, auto, auto-flow > re1: [ITHREAD] > pcib3: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0 > pci3: <ACPI PCI bus> on pcib3 > pcib4: <ACPI PCI-PCI bridge> irq 18 at device 0.0 on pci3 > pci4: <ACPI PCI bus> on pcib4 > ehci1: <EHCI (generic) USB 2.0 controller> mem 0xf7d07000-0xf7d073ff irq > 23 at device 29.0 on pci0 > ehci1: [ITHREAD] > usbus1: EHCI version 1.0 > usbus1: <EHCI (generic) USB 2.0 controller> on ehci1 > isab0: <PCI-ISA bridge> at device 31.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <Intel Panther Point SATA300 controller> port > 0xf0b0-0xf0b7,0xf0a0-0xf0a3,0xf090-0xf097,0xf080-0xf083,0xf060-0xf07f > mem 0xf7d06000-0xf7d067ff irq 19 at device 31.2 on pci0 > atapci0: [ITHREAD] > atapci0: AHCI called from vendor specific driver > atapci0: AHCI v1.30 controller with 4 6Gbps ports, PM not supported > ata2: <ATA channel> at channel 0 on atapci0 > ata2: [ITHREAD] > pci0: <serial bus, SMBus> at device 31.3 (no driver attached) > acpi_button0: <Power Button> on acpi0 > acpi_tz0: <Thermal Zone> on acpi0 > acpi_tz1: <Thermal Zone> on acpi0 > acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on > acpi0 > Timecounter "HPET" frequency 14318180 Hz quality 900 > atrtc0: <AT realtime clock> port 0x70-0x77 irq 8 on acpi0 > atrtc0: Warning: Couldn't map I/O. > uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 > uart0: [FILTER] > uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0 > uart1: [FILTER] > ppc1: <Parallel port> port 0x378-0x37f,0x778-0x77f irq 5 drq 3 on acpi0 > ppc1: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode > ppc1: FIFO with 16/16/16 bytes threshold > ppc1: [ITHREAD] > ppbus0: <Parallel port bus> on ppc1 > plip0: <PLIP network interface> on ppbus0 > plip0: [ITHREAD] > lpt0: <Printer> on ppbus0 > lpt0: [ITHREAD] > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > kbd0 at atkbd0 > atkbd0: [GIANT-LOCKED] > atkbd0: [ITHREAD] > ppc0: cannot reserve I/O port range > est0: <Enhanced SpeedStep Frequency Control> on cpu0 > p4tcc0: <CPU Frequency Thermal Control> on cpu0 > est1: <Enhanced SpeedStep Frequency Control> on cpu1 > p4tcc1: <CPU Frequency Thermal Control> on cpu1 > Timecounters tick every 1.000 msec > IPsec: Initialized Security Association Processing. > usbus0: 480Mbps High Speed USB v2.0 > usbus1: 480Mbps High Speed USB v2.0 > ad4: 476940MB <Seagate ST95005620AS SD28> at ata2-master UDMA100 SATA 3Gb/s > ugen0.1: <Intel> at usbus0 > uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0 > ugen1.1: <Intel> at usbus1 > uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 > uhub0: 2 ports with 2 removable, self powered > uhub1: 2 ports with 2 removable, self powered > ugen0.2: <vendor 0x8087> at usbus0 > uhub2: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> > on usbus0 > ugen1.2: <vendor 0x8087> at usbus1 > uhub3: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> > on usbus1 > uhub2: 4 ports with 4 removable, self powered > uhub3: 4 ports with 4 removable, self powered > SMP: AP CPU #1 Launched! > Trying to mount root from ufs:/dev/ad4s1a > ZFS NOTICE: Prefetch is disabled by default if less than 4GB of RAM is > present; > to enable, add "vfs.zfs.prefetch_disable=0" to > /boot/loader.conf. > ZFS WARNING: Recommended minimum kmem_size is 512MB; expect unstable > behavior. > Consider tuning vm.kmem_size and vm.kmem_size_max > in /boot/loader.conf. > ZFS filesystem version 5 > ZFS storage pool version 28 > re0: link state changed to DOWN > re1: link state changed to DOWN > pflog0: promiscuous mode enabled > re1: link state changed to UP > > cryptosoft0: <software crypto> on motherboard > padlock0: No ACE support. > acpi0: <ALASKA A M I> on motherboard > acpi0: [ITHREAD] > acpi0: Power Button (fixed) > acpi0: reservation of 67, 1 (4) failed > Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 > acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 > cpu0: <ACPI CPU> on acpi0 > cpu1: <ACPI CPU> on acpi0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > vgapci0: <VGA-compatible display> port 0xf000-0xf03f mem > 0xf7800000-0xf7bfffff,0xe0000000-0xefffffff irq 16 at device 2.0 on pci0 > pci0: <simple comms> at device 22.0 (no driver attached) > ehci0: <EHCI (generic) USB 2.0 controller> mem 0xf7d08000-0xf7d083ff irq > 16 at device 26.0 on pci0 > ehci0: [ITHREAD] > usbus0: EHCI version 1.0 > usbus0: <EHCI (generic) USB 2.0 controller> on ehci0 > pci0: <multimedia, HDA> at device 27.0 (no driver attached) > pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0 > pci1: <ACPI PCI bus> on pcib1 > re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F PCIe Gigabit Ethernet> port > 0xe000-0xe0ff mem 0xf7c00000-0xf7c00fff,0xf0100000-0xf0103fff irq 16 at > device 0.0 on pci1 > re0: Using 1 MSI-X message > re0: Chip rev. 0x2c800000 > re0: MAC rev. 0x00000000 > miibus0: <MII bus> on re0 > rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus0 > rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, > 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, > 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, > 1000baseT-FDX-flow-master, auto, auto-flow > re0: [ITHREAD] > pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.1 on pci0 > pci2: <ACPI PCI bus> on pcib2 > re1: <RealTek 8168/8111 B/C/CP/D/DP/E/F PCIe Gigabit Ethernet> port > 0xd000-0xd0ff mem 0xf0004000-0xf0004fff,0xf0000000-0xf0003fff irq 17 at > device 0.0 on pci2 > re1: Using 1 MSI-X message > re1: Chip rev. 0x2c800000 > re1: MAC rev. 0x00000000 > miibus1: <MII bus> on re1 > rgephy1: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus1 > rgephy1: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, > 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, > 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, > 1000baseT-FDX-flow-master, auto, auto-flow > re1: [ITHREAD] > pcib3: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0 > pci3: <ACPI PCI bus> on pcib3 > pcib4: <ACPI PCI-PCI bridge> irq 18 at device 0.0 on pci3 > pci4: <ACPI PCI bus> on pcib4 > ehci1: <EHCI (generic) USB 2.0 controller> mem 0xf7d07000-0xf7d073ff irq > 23 at device 29.0 on pci0 > ehci1: [ITHREAD] > usbus1: EHCI version 1.0 > usbus1: <EHCI (generic) USB 2.0 controller> on ehci1 > isab0: <PCI-ISA bridge> at device 31.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <Intel Panther Point SATA300 controller> port > 0xf0b0-0xf0b7,0xf0a0-0xf0a3,0xf090-0xf097,0xf080-0xf083,0xf060-0xf07f > mem 0xf7d06000-0xf7d067ff irq 19 at device 31.2 on pci0 > atapci0: [ITHREAD] > atapci0: AHCI called from vendor specific driver > atapci0: AHCI v1.30 controller with 4 6Gbps ports, PM not supported > ata2: <ATA channel> at channel 0 on atapci0 > ata2: [ITHREAD] > pci0: <serial bus, SMBus> at device 31.3 (no driver attached) > acpi_button0: <Power Button> on acpi0 > acpi_tz0: <Thermal Zone> on acpi0 > acpi_tz1: <Thermal Zone> on acpi0 > acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on > acpi0 > Timecounter "HPET" frequency 14318180 Hz quality 900 > atrtc0: <AT realtime clock> port 0x70-0x77 irq 8 on acpi0 > atrtc0: Warning: Couldn't map I/O. > uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 > uart0: [FILTER] > uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0 > uart1: [FILTER] > ppc1: <Parallel port> port 0x378-0x37f,0x778-0x77f irq 5 drq 3 on acpi0 > ppc1: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode > ppc1: FIFO with 16/16/16 bytes threshold > ppc1: [ITHREAD] > ppbus0: <Parallel port bus> on ppc1 > plip0: <PLIP network interface> on ppbus0 > plip0: [ITHREAD] > lpt0: <Printer> on ppbus0 > lpt0: [ITHREAD] > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > kbd0 at atkbd0 > atkbd0: [GIANT-LOCKED] > atkbd0: [ITHREAD] > ppc0: cannot reserve I/O port range > est0: <Enhanced SpeedStep Frequency Control> on cpu0 > p4tcc0: <CPU Frequency Thermal Control> on cpu0 > est1: <Enhanced SpeedStep Frequency Control> on cpu1 > p4tcc1: <CPU Frequency Thermal Control> on cpu1 > Timecounters tick every 1.000 msec > IPsec: Initialized Security Association Processing. > usbus0: 480Mbps High Speed USB v2.0 > usbus1: 480Mbps High Speed USB v2.0 > ad4: 476940MB <Seagate ST95005620AS SD28> at ata2-master UDMA100 SATA 3Gb/s > ugen0.1: <Intel> at usbus0 > uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0 > ugen1.1: <Intel> at usbus1 > uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 > uhub0: 2 ports with 2 removable, self powered > uhub1: 2 ports with 2 removable, self powered > ugen0.2: <vendor 0x8087> at usbus0 > uhub2: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> > on usbus0 > ugen1.2: <vendor 0x8087> at usbus1 > uhub3: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> > on usbus1 > uhub2: 4 ports with 4 removable, self powered > uhub3: 4 ports with 4 removable, self powered > SMP: AP CPU #1 Launched! > Trying to mount root from ufs:/dev/ad4s1a > ZFS NOTICE: Prefetch is disabled by default if less than 4GB of RAM is > present; > to enable, add "vfs.zfs.prefetch_disable=0" to > /boot/loader.conf. > ZFS WARNING: Recommended minimum kmem_size is 512MB; expect unstable > behavior. > Consider tuning vm.kmem_size and vm.kmem_size_max > in /boot/loader.conf. > ZFS filesystem version 5 > ZFS storage pool version 28 > re0: link state changed to DOWN > re1: link state changed to DOWN > pflog0: promiscuous mode enabled > re1: link state changed to UP > > [email protected] <- Do not Use > > > > > > _______________________________________________ > List mailing list > [email protected] > http://lists.pfsense.org/mailman/listinfo/list > _______________________________________________ List mailing list [email protected] http://lists.pfsense.org/mailman/listinfo/list
