Fabian Bertholm wrote:
> Hi,
>
> I try to run ath9k on a P1020RDB Freescale board.
> I run into the problem similar to the Bug/Patch here:
> http://patchwork.ozlabs.org/patch/52137/
>
> I get irq 16: nobody cared....
Firstly you should check if 'irq 16' is issue from your PCIe device.
>
> I tried to fix the dts file in the same manner but this does not help.
> Currently I am using 2.6.33.7
>
> Any hints? Anybody?
>
Then if so I think it's unnecessary to add any #interrupt-map on dts since MSI
is used as interrupt mode on P1020RDB, not legacy interrupt. So please remove
all #interrupt-map on both pci nodes, then enable CONFIG_PCI_MSI to build/boot
again.
> The modified pci section from my dts:
>
> pci0: p...@ffe09000 {
> cell-index = <1>;
> compatible = "fsl,mpc8548-pcie";
> device_type = "pci";
> #interrupt-cells = <1>;
> #size-cells = <2>;
> #address-cells = <3>;
> reg = <0 0xffe09000 0 0x1000>;
> bus-range = <0 255>;
> ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
> 0x1000000 0x0 0x00000000 0 0xffc30000 0x0 0x10000>;
> clock-frequency = <33333333>;
> interrupt-parent = <&mpic>;
> interrupts = <16 2>;
> interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
> interrupt-map = <
> /* IDSEL 0x0 */
> 0000 0x0 0x0 0x1 &mpic 0x4 0x2
> 0000 0x0 0x0 0x2 &mpic 0x5 0x2
> 0000 0x0 0x0 0x3 &mpic 0x6 0x2
> 0000 0x0 0x0 0x4 &mpic 0x7 0x2
I don't know how you generate these interrupt-map. So even you really want to
use legacy interrupt you should make sure your PCIe bus number/device
number/function number, and actual interrupt number. Especially please check
interrupt trigger sense. Sometimes incorrect sense will issue your PCIe to
receive interrupt storm. As a result no interrupt handler deal with this
spurious interrupt like you saw 'irq 16: nobody cared'.
> >;
> p...@0 {
> reg = <0x0 0x0 0x0 0x0 0x0>;
> #size-cells = <2>;
> #address-cells = <3>;
> device_type = "pci";
> ranges = <0x2000000 0x0 0xa0000000
> 0x2000000 0x0 0xa0000000
> 0x0 0x20000000
>
> 0x1000000 0x0 0x0
> 0x1000000 0x0 0x0
> 0x0 0x100000>;
> };
> };
>
> pci1: p...@ffe0a000 {
> cell-index = <2>;
> compatible = "fsl,mpc8548-pcie";
> device_type = "pci";
> #interrupt-cells = <1>;
> #size-cells = <2>;
> #address-cells = <3>;
> reg = <0 0xffe0a000 0 0x1000>;
> bus-range = <0 255>;
> ranges = <0x2000000 0x0 0xc0000000 0 0xc0000000 0x0 0x20000000
> 0x1000000 0x0 0x00000000 0 0xffc20000 0x0 0x10000>;
> clock-frequency = <33333333>;
> interrupt-parent = <&mpic>;
> interrupts = <16 2>;
> interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
> interrupt-map = <
> /* IDSEL 0x0 */
> 0000 0x0 0x0 0x1 &mpic 0x0 0x1
> 0000 0x0 0x0 0x2 &mpic 0x1 0x1
> 0000 0x0 0x0 0x3 &mpic 0x2 0x1
> 0000 0x0 0x0 0x4 &mpic 0x3 0x1
> >;
>
There are two PCIe controller so you also have to make sure which controller
your device exist.
-Tiejun
> p...@0 {
> reg = <0x0 0x0 0x0 0x0 0x0>;
> #size-cells = <2>;
> #address-cells = <3>;
> device_type = "pci";
> ranges = <0x2000000 0x0 0xc0000000
> 0x2000000 0x0 0xc0000000
> 0x0 0x20000000
>
> 0x1000000 0x0 0x0
> 0x1000000 0x0 0x0
> 0x0 0x100000>;
> };
> };
>
>
> Best Regards,
> Fabian
> _______________________________________________
> Linuxppc-dev mailing list
> Linuxppc-dev@lists.ozlabs.org
> https://lists.ozlabs.org/listinfo/linuxppc-dev
>
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@lists.ozlabs.org
https://lists.ozlabs.org/listinfo/linuxppc-dev
