Hi,

I try to run ath9k on a P1020RDB Freescale board.
I run into the problem similar to the Bug/Patch here:
http://patchwork.ozlabs.org/patch/52137/

I get irq 16: nobody cared....

I tried to fix the dts file in the same manner but this does not help.
Currently I am using 2.6.33.7

Any hints? Anybody?

The modified pci section from my dts:

        pci0: p...@ffe09000 {
                cell-index = <1>;
                compatible = "fsl,mpc8548-pcie";
                device_type = "pci";
                #interrupt-cells = <1>;
                #size-cells = <2>;
                #address-cells = <3>;
                reg = <0 0xffe09000 0 0x1000>;
                bus-range = <0 255>;
                ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
                          0x1000000 0x0 0x00000000 0 0xffc30000 0x0 0x10000>;
                clock-frequency = <33333333>;
                interrupt-parent = <&mpic>;
                interrupts = <16 2>;
                interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
                interrupt-map = <
                        /* IDSEL 0x0 */
                        0000 0x0 0x0 0x1 &mpic 0x4 0x2
                        0000 0x0 0x0 0x2 &mpic 0x5 0x2
                        0000 0x0 0x0 0x3 &mpic 0x6 0x2
                        0000 0x0 0x0 0x4 &mpic 0x7 0x2
                        >;
                p...@0 {
                        reg = <0x0 0x0 0x0 0x0 0x0>;
                        #size-cells = <2>;
                        #address-cells = <3>;
                        device_type = "pci";
                        ranges = <0x2000000 0x0 0xa0000000
                                  0x2000000 0x0 0xa0000000
                                  0x0 0x20000000

                                  0x1000000 0x0 0x0
                                  0x1000000 0x0 0x0
                                  0x0 0x100000>;
                };
        };

        pci1: p...@ffe0a000 {
                cell-index = <2>;
                compatible = "fsl,mpc8548-pcie";
                device_type = "pci";
                #interrupt-cells = <1>;
                #size-cells = <2>;
                #address-cells = <3>;
                reg = <0 0xffe0a000 0 0x1000>;
                bus-range = <0 255>;
                ranges = <0x2000000 0x0 0xc0000000 0 0xc0000000 0x0 0x20000000
                          0x1000000 0x0 0x00000000 0 0xffc20000 0x0 0x10000>;
                clock-frequency = <33333333>;
                interrupt-parent = <&mpic>;
                interrupts = <16 2>;
                interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
                interrupt-map = <
                        /* IDSEL 0x0 */
                        0000 0x0 0x0 0x1 &mpic 0x0 0x1
                        0000 0x0 0x0 0x2 &mpic 0x1 0x1
                        0000 0x0 0x0 0x3 &mpic 0x2 0x1
                        0000 0x0 0x0 0x4 &mpic 0x3 0x1
                        >;

                p...@0 {
                        reg = <0x0 0x0 0x0 0x0 0x0>;
                        #size-cells = <2>;
                        #address-cells = <3>;
                        device_type = "pci";
                        ranges = <0x2000000 0x0 0xc0000000
                                  0x2000000 0x0 0xc0000000
                                  0x0 0x20000000

                                  0x1000000 0x0 0x0
                                  0x1000000 0x0 0x0
                                  0x0 0x100000>;
                };
        };


Best Regards,
Fabian
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@lists.ozlabs.org
https://lists.ozlabs.org/listinfo/linuxppc-dev

Reply via email to