On Fri, Jan 22, 2010 at 09:17:55PM +0100, Albrecht Dreß wrote:
> Improve the recovery of the MPC5200B's I2C bus from errors like bus
> hangs.
>
> Signed-off-by: Albrecht Dreß <albrecht.dr...@arcor.de>
>
> ---
>
> This patch introduces several improvements to the MPC5200B's I2C driver
> as to improve the recovery from error conditions I encountered when
> testing a custom board with several I2C devices attached (eeprom, io
> expander, rtc, sensors). The error conditions included cases where the
> bus if logic of one slave apparently went south, blocking the bus
> completely.
>
> My fixes include:
> 1. make the bus timeout configurable in fsl_i2c_probe(); the default of
> one second is *way* too long for my use case;
> 2. if a timeout condition occurs in mpc_xfer(), mpc_i2c_fixup() the bus
> if *any* of the CF, BB and RXAK flags in the MSR is 1. I actually
> saw different combinations with hangs, not only all three set;
Hello Albrecht,
I see this exact hang on a MPC8349EA board. I poll my i2c sensors every
500ms, and it takes around 12 hours to produce a hang. The usual hang
has (CF | BB) set, however I have seen a hang with just BB (only once so
far in about 2 weeks).
I think the fixup should be run on 8349 as well, if not all processors.
I'm happy to test patches. I have a way to reliably trigger a lockup,
using another master on the i2c bus.
> 3. improve the fixup procedure by calculating the timing needed from the
> real (configured) bus clock, calculated in mpc_i2c_setclock_52xx().
> Furthermore, I issue 9 instead of one cycle, as I experienced cases
> where the single one is not enough (found this tip in a forum). As a
> side effect, the new scheme needs only 81us @375kHz bus clock instead
> of 150us. I recorded waveforms for 18.4kHz, 85.9kHz and 375kHz, all
> looking fine, which I can provide if anyone is interested.
>
> Open questions:
> - is the approach correct at all, in particular the interpretation of
> the flags (#2)?
> - could this code also be used on non-5200 processors?
>
> --- linux-2.6.32-orig/drivers/i2c/busses/i2c-mpc.c 2009-12-03
> 04:51:21.000000000 +0100
> +++ linux-2.6.32/drivers/i2c/busses/i2c-mpc.c 2010-01-22 16:05:13.000000000
> +0100
> @@ -59,6 +59,7 @@ struct mpc_i2c {
> wait_queue_head_t queue;
> struct i2c_adapter adap;
> int irq;
> + u32 real_clk;
> };
>
> struct mpc_i2c_divider {
> @@ -97,16 +98,32 @@ static irqreturn_t mpc_i2c_isr(int irq,
> */
> static void mpc_i2c_fixup(struct mpc_i2c *i2c)
> {
> - writeccr(i2c, 0);
> - udelay(30);
> - writeccr(i2c, CCR_MEN);
> - udelay(30);
> - writeccr(i2c, CCR_MSTA | CCR_MTX);
> - udelay(30);
> - writeccr(i2c, CCR_MSTA | CCR_MTX | CCR_MEN);
> - udelay(30);
> - writeccr(i2c, CCR_MEN);
> - udelay(30);
> + if (i2c->real_clk == 0) {
> + writeccr(i2c, 0);
> + udelay(30);
> + writeccr(i2c, CCR_MEN);
> + udelay(30);
> + writeccr(i2c, CCR_MSTA | CCR_MTX);
> + udelay(30);
> + writeccr(i2c, CCR_MSTA | CCR_MTX | CCR_MEN);
> + udelay(30);
> + writeccr(i2c, CCR_MEN);
> + udelay(30);
> + } else {
> + int k;
> + u32 delay_val = 1000000 / i2c->real_clk + 1;
> +
> + if (delay_val < 2)
> + delay_val = 2;
> +
> + for (k = 9; k; k--) {
> + writeccr(i2c, 0);
> + writeccr(i2c, CCR_MSTA | CCR_MTX | CCR_MEN);
> + udelay(delay_val);
> + writeccr(i2c, CCR_MEN);
> + udelay(delay_val << 1);
> + }
> + }
> }
>
The old sequence has always un-hung the bus for me. Yours might be
better. I'll try it next time the bus wedges up on me.
> static int i2c_wait(struct mpc_i2c *i2c, unsigned timeout, int writing)
> @@ -186,15 +203,18 @@ static const struct mpc_i2c_divider mpc_
> {10240, 0x9d}, {12288, 0x9e}, {15360, 0x9f}
> };
>
> -int mpc_i2c_get_fdr_52xx(struct device_node *node, u32 clock, int prescaler)
> +int mpc_i2c_get_fdr_52xx(struct device_node *node, u32 clock, int prescaler,
> + u32 *real_clk)
> {
> const struct mpc_i2c_divider *div = NULL;
> unsigned int pvr = mfspr(SPRN_PVR);
> u32 divider;
> int i;
>
> - if (!clock)
> + if (!clock) {
> + *real_clk = 0;
> return -EINVAL;
> + }
>
> /* Determine divider value */
> divider = mpc5xxx_get_bus_frequency(node) / clock;
> @@ -212,7 +232,8 @@ int mpc_i2c_get_fdr_52xx(struct device_n
> break;
> }
>
> - return div ? (int)div->fdr : -EINVAL;
> + *real_clk = mpc5xxx_get_bus_frequency(node) / div->divider;
> + return (int)div->fdr;
> }
>
> static void mpc_i2c_setclock_52xx(struct device_node *node,
> @@ -221,13 +242,14 @@ static void mpc_i2c_setclock_52xx(struct
> {
> int ret, fdr;
>
> - ret = mpc_i2c_get_fdr_52xx(node, clock, prescaler);
> + ret = mpc_i2c_get_fdr_52xx(node, clock, prescaler, &i2c->real_clk);
> fdr = (ret >= 0) ? ret : 0x3f; /* backward compatibility */
>
> writeb(fdr & 0xff, i2c->base + MPC_I2C_FDR);
>
> if (ret >= 0)
> - dev_info(i2c->dev, "clock %d Hz (fdr=%d)\n", clock, fdr);
> + dev_info(i2c->dev, "clock %u Hz (fdr=%d)\n", i2c->real_clk,
> + fdr);
> }
> #else /* !CONFIG_PPC_MPC52xx */
> static void mpc_i2c_setclock_52xx(struct device_node *node,
> @@ -446,10 +468,14 @@ static int mpc_xfer(struct i2c_adapter *
> return -EINTR;
> }
> if (time_after(jiffies, orig_jiffies + HZ)) {
> + u8 status = readb(i2c->base + MPC_I2C_SR);
> +
> dev_dbg(i2c->dev, "timeout\n");
> - if (readb(i2c->base + MPC_I2C_SR) ==
> - (CSR_MCF | CSR_MBB | CSR_RXAK))
> + if ((status & (CSR_MCF | CSR_MBB | CSR_RXAK)) != 0) {
> + writeb(status & ~CSR_MAL,
> + i2c->base + MPC_I2C_SR);
> mpc_i2c_fixup(i2c);
> + }
> return -EIO;
> }
> schedule();
This hunk looks good to me. It is basically what I did, except I didn't
clear the MAL bit. Judging by the manual, it should be cleared.
> @@ -540,6 +566,14 @@ static int __devinit fsl_i2c_probe(struc
> }
> }
>
> + prop = of_get_property(op->node, "timeout", &plen);
> + if (prop && plen == sizeof(u32)) {
> + mpc_ops.timeout = *prop * HZ / 1000000;
> + if (mpc_ops.timeout < 5)
> + mpc_ops.timeout = 5;
> + }
> + dev_info(i2c->dev, "timeout %u us\n", mpc_ops.timeout * 1000000 / HZ);
> +
> dev_set_drvdata(&op->dev, i2c);
>
> i2c->adap = mpc_ops;
>
Ira
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@lists.ozlabs.org
https://lists.ozlabs.org/listinfo/linuxppc-dev
