> Here is a complete startup log, with debug turned on as you requested. > This is still against 2.6.27.9, as it will take me a little time to > build 2.6.28. Hopefully, this log will be useful in the meantime.
Can you add "debug" to your kernel command line option or send the output of the "dmesg" command please ? Cheers, Ben. > Steve > > > U-Boot 2008.10-00079-gebb3412 (Dec 9 2008 - 16:06:05) > > CPU: AMCC PowerPC 440EPx Rev. A at 666.666 MHz (PLB=166, OPB=83, EBC=55 MHz) > Security/Kasumi support > Bootstrap Option H - Boot ROM Location I2C (Addr 0x52) > Internal PCI arbiter enabled, PCI async ext clock used > 32 kB I-Cache 32 kB D-Cache > Board: Sequoia - AMCC PPC440EPx Evaluation Board, Rev. F, PCI=66 MHz, serial# > 7654 > I2C: ready > SPI: ready > DTT: 1 is 27 C > DRAM: 256 MB > FLASH: 64 MB > NAND: 32 MiB > PCI: Bus Dev VenId DevId Class Int > 01 00 1172 0004 ff00 43 > 00 0c 10b5 8112 0604 43 > In: serial > Out: serial > Err: serial > RTC: ready > USB: Host(int phy) Device(ext phy) > Net: ppc_4xx_eth0, ppc_4xx_eth1 > IDE: Bus 0: OK > Device 0: PIO mode 4 > Model: SMC01GBFK6E Firm: CF080204 Ser#: NU0B4000000000102893 > Type: Hard Disk > Capacity: 977.4 MB = 0.9 GB (2001888 x 512) > > > > ========================================================== > | | > | Welcome to Hydra | > | | > ========================================================== > > > > Please type "sm" to enter safe-mode. > > > Starting current kernel - please wait. > Starting previous kernel - please wait. > Starting safe-mode kernel - please wait. > ## Booting kernel from Legacy Image at fd400000 ... > Image Name: Linux-2.6.27.9-00045-gcccf182-di > Created: 2009-01-05 21:29:41 UTC > Image Type: PowerPC Linux Kernel Image (gzip compressed) > Data Size: 1684167 Bytes = 1.6 MB > Load Address: 00400000 > Entry Point: 00400454 > Verifying Checksum ... OK > ## Loading init Ramdisk from Legacy Image at fd900000 ... > Image Name: initramfs > Created: 2008-11-26 15:13:12 UTC > Image Type: PowerPC Linux RAMDisk Image (gzip compressed) > Data Size: 2443397 Bytes = 2.3 MB > Load Address: 00000000 > Entry Point: 00000000 > Verifying Checksum ... OK > Uncompressing Kernel Image ... OK > Loading Ramdisk to 0fcb7000, end 0ff0b885 ... OK > CPU clock-frequency <- 0x27bc86a4 (667MHz) > CPU timebase-frequency <- 0x27bc86a4 (667MHz) > /plb: clock-frequency <- 9ef21a9 (167MHz) > /plb/opb: clock-frequency <- 4f790d4 (83MHz) > /plb/opb/ebc: clock-frequency <- 34fb5e3 (56MHz) > /plb/opb/ser...@ef600300: clock-frequency <- a8c000 (11MHz) > /plb/opb/ser...@ef600400: clock-frequency <- a8c000 (11MHz) > /plb/opb/ser...@ef600500: clock-frequency <- a8c000 (11MHz) > /plb/opb/ser...@ef600600: clock-frequency <- a8c000 (11MHz) > Memory <- <0x0 0x0 0xffff000> (255MB) > ENET0: local-mac-address <- 00:10:ec:01:04:d0 > ENET1: local-mac-address <- 00:10:ec:01:04:d1 > > zImage starting: loaded at 0x00400000 (sp: 0x0ff0c300) > Allocating 0x371974 bytes for kernel ... > gunzipping (0x00000000 <- 0x0040f000:0x007ac72c)...done 0x35a1e4 bytes > Using loader supplied ramdisk at 0xfcb7000-0xff0b885 > initrd head: 0x1f8b0808 > > Linux/PowerPC load: root=/dev/sda3 rw > ip=137.237.178.105:137.237.179.31:137.237.178.1:255.255.255.0:hydra_temp:eth0:off > panic=1 console=ttyS0,115200 > Finalizing device tree... flat tree at 0x40bf08 > Using Hydra_temp machine description > Linux version 2.6.27.9-00045-gcccf182-dirty (sfa...@saf.cs.myharris.net) (gcc > version 4.2.2) #135 Mon Jan 5 16:29:11 EST 2009 > Found initrd at 0xcfcb7000:0xcff0b885 > console [udbg0] enabled > setup_arch: bootmem > arch: exit > Zone PFN ranges: > DMA 0x00000000 -> 0x0000ffff > Normal 0x0000ffff -> 0x0000ffff > Movable zone start PFN for each node > early_node_map[1] active PFN ranges > 0: 0x00000000 -> 0x0000ffff > Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65023 > Kernel command line: root=/dev/sda3 rw > ip=137.237.178.105:137.237.179.31:137.237.178.1:255.255.255.0:hydra_temp:eth0:off > panic=1 console=ttyS0,115200 > UIC0 (32 IRQ sources) at DCR 0xc0 > UIC1 (32 IRQ sources) at DCR 0xd0 > UIC2 (32 IRQ sources) at DCR 0xe0 > PID hash table entries: 1024 (order: 10, 4096 bytes) > clocksource: timebase mult[600000] shift[22] registered > Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) > Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) > Memory: 253620k/262140k available (3284k kernel code, 8220k reserved, 124k > data, 90k bss, 156k init) > SLUB: Genslabs=10, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 > Calibrating delay loop... 1331.20 BogoMIPS (lpj=2662400) > Mount-cache hash table entries: 512 > net_namespace: 288 bytes > NET: Registered protocol family 16 > > PCI host bridge /plb/p...@1ec000000 (primary) ranges: > MEM 0x0000000180000000..0x000000018fffffff -> 0x0000000080000000 > IO 0x00000001e8000000..0x00000001e80fffff -> 0x0000000000000000 > 4xx PCI DMA offset set to 0x00000000 > PCI: Probing PCI hardware > PCI: Hiding 4xx host bridge resources 0000:00:00.0 > pci 0000:00:0c.0: PME# supported from D0 D1 D3hot > pci 0000:00:0c.0: PME# disabled > Try to map irq for 0000:00:00.0... > pci_busdev_to_OF_node(0,0x0) > parent is /plb/p...@1ec000000 > result is <NULL> > -> got one, spec 2 cells (0x00000003 0x00000008...) on /interrupt-controller2 > -> mapped to linux irq 16 > Try to map irq for 0000:00:0c.0... > pci_busdev_to_OF_node(0,0x60) > parent is /plb/p...@1ec000000 > result is <NULL> > -> got one, spec 2 cells (0x00000003 0x00000008...) on /interrupt-controller2 > -> mapped to linux irq 16 > Try to map irq for 0000:01:00.0... > pci_busdev_to_OF_node(1,0x0) > pci_busdev_to_OF_node(0,0x60) > parent is /plb/p...@1ec000000 > result is <NULL> > -> got one, spec 2 cells (0x00000003 0x00000008...) on /interrupt-controller2 > -> mapped to linux irq 16 > PCI: PHB (bus 0) bridge rsrc 0: 0000000000000000-00000000000fffff [0x100], > parent c0339b40 (PCI IO) > PCI: PHB (bus 0) bridge rsrc 1: 0000000180000000-000000018fffffff [0x200], > parent c0339b18 (PCI mem) > PCI: Assigning unassigned resouces... > pci 0000:00:0c.0: BAR 8: can't allocate mem resource [0x180000000-0x18fffffff] > pci 0000:01:00.0: BAR 1: can't allocate mem resource [0x1f0000000-0x1ffffffff] > pci 0000:01:00.0: BAR 0: can't allocate mem resource [0x180000000-0x18007ffff] > pci 0000:00:0c.0: PCI bridge, secondary bus 0000:01 > pci 0000:00:0c.0: IO window: disabled > pci 0000:00:0c.0: MEM window: disabled > pci 0000:00:0c.0: PREFETCH window: disabled > bus: 00 index 0 io port: [0, fffff] > bus: 00 index 1 mmio: [180000000, 18fffffff] > bus: 01 index 0 mmio: [0, 0] > bus: 01 index 1 mmio: [0, 0] > bus: 01 index 2 mmio: [0, 0] > bus: 01 index 3 mmio: [0, 0] > SCSI subsystem initialized > usbcore: registered new interface driver usbfs > usbcore: registered new interface driver hub > usbcore: registered new device driver usb > NET: Registered protocol family 2 > IP route cache hash table entries: 2048 (order: 1, 8192 bytes) > TCP established hash table entries: 8192 (order: 4, 65536 bytes) > TCP bind hash table entries: 8192 (order: 3, 32768 bytes) > TCP: Hash tables configured (established 8192 bind 8192) > TCP reno registered > NET: Registered protocol family 1 > checking if image is initramfs... it is > Freeing initrd memory: 2386k freed > msgmni has been set to 500 > io scheduler noop registered > io scheduler anticipatory registered (default) > io scheduler deadline registered > io scheduler cfq registered > Serial: 8250/16550 driver4 ports, IRQ sharing enabled > serial8250.0: ttyS0 at MMIO 0x1ef600300 (irq = 17) is a 16550A > console > handover: boot [udbg0] -> real [ttyS0] > serial8250.0: ttyS1 at MMIO 0x1ef600400 (irq = 18) is a 16550A > serial8250.0: ttyS2 at MMIO 0x1ef600500 (irq = 19) is a 16550A > serial8250.0: ttyS3 at MMIO 0x1ef600600 (irq = 20) is a 16550A > 1ef600300.serial: ttyS0 at MMIO 0x1ef600300 (irq = 17) is a 16550A > 1ef600400.serial: ttyS1 at MMIO 0x1ef600400 (irq = 18) is a 16550A > 1ef600500.serial: ttyS2 at MMIO 0x1ef600500 (irq = 19) is a 16550A > 1ef600600.serial: ttyS3 at MMIO 0x1ef600600 (irq = 20) is a 16550A > brd: module loaded > PPC 4xx OCP EMAC driver, version 3.54 > MAL v2 /plb/mcmal, 2 TX channels, 2 RX channels > ZMII /plb/opb/emac-z...@ef600d00 initialized > RGMII /plb/opb/emac-rg...@ef601000 initialized with MDIO support > /plb/opb/emac-rg...@ef601000: input 0 in RGMII mode > eth0: EMAC-0 /plb/opb/ether...@ef600e00, MAC 00:10:ec:01:04:d0 > eth0: found Marvell 88E1111 Ethernet PHY (0x00) > /plb/opb/emac-rg...@ef601000: input 1 in RGMII mode > eth1: EMAC-1 /plb/opb/ether...@ef600f00, MAC 00:10:ec:01:04:d1 > eth1: found Marvell 88E1111 Ethernet PHY (0x01) > Uniform Multi-Platform E-IDE driver > Driver 'sd' needs updating - please use bus_type methods > scsi0 : pata_platform > ata1: PATA max PIO6 mmio cmd 0x1c1000000 ctl 0x1c1000098 irq 32 > ata1.00: ATA-0: SMC01GBFK6E, CF080204, max MWDMA2 > ata1.00: 2001888 sectors, multi 0: LBA > ata1.00: configured for PIO > ata1.00: configured for PIO > ata1: EH complete > scsi 0:0:0:0: Direct-Access ATA SMC01GBFK6E CF08 PQ: 0 ANSI: 5 > sd 0:0:0:0: [sda] 2001888 512-byte hardware sectors (1025 MB) > sd 0:0:0:0: [sda] Write Protect is off > sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support > DPO or FUA > sd 0:0:0:0: [sda] 2001888 512-byte hardware sectors (1025 MB) > sd 0:0:0:0: [sda] Write Protect is off > sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support > DPO or FUA > sda: sda1 sda2 sda3 sda4 > sd 0:0:0:0: [sda] Attached SCSI disk > sd 0:0:0:0: Attached scsi generic sg0 type 0 > 1fc000000.nor_flash: Found 1 x16 devices at 0x0 in 16-bit bank > Amd/Fujitsu Extended Query Table at 0x0040 > 1fc000000.nor_flash: CFI does not contain boot bank location. Assuming top. > number of CFI chips: 1 > cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. > RedBoot partition parsing not available > Creating 9 MTD partitions on "1fc000000.nor_flash": > 0x00000000-0x00500000 : "kernel0" > 0x00500000-0x00a00000 : "ramdisk0" > 0x00a00000-0x00f00000 : "kernel1" > 0x00f00000-0x01400000 : "ramdisk1" > 0x01400000-0x01900000 : "kernel2" > 0x01900000-0x01e00000 : "ramdisk2" > 0x03f60000-0x03f80000 : "env0" > 0x03f80000-0x03fa0000 : "env1" > 0x03fa0000-0x04000000 : "u-boot" > spi_ppc4xx_of 1ef600900.spi: driver initialized > ppc-of-ehci e0000300.ehci: OF EHCI > ppc-of-ehci e0000300.ehci: new USB bus registered, assigned bus number 1 > ppc-of-ehci e0000300.ehci: irq 34, io mem 0xe0000300 > ppc-of-ehci e0000300.ehci: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 > usb usb1: configuration #1 chosen from 1 choice > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 1 port detected > usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 > usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb1: Product: OF EHCI > usb usb1: Manufacturer: Linux 2.6.27.9-00045-gcccf182-dirty ehci_hcd > usb usb1: SerialNumber: PPC-OF USB > ppc-of-ohci e0000400.usb: OF OHCI > ppc-of-ohci e0000400.usb: new USB bus registered, assigned bus number 2 > ppc-of-ohci e0000400.usb: irq 35, io mem 0xe0000400 > usb usb2: configuration #1 chosen from 1 choice > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 1 port detected > usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 > usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb2: Product: OF OHCI > usb usb2: Manufacturer: Linux 2.6.27.9-00045-gcccf182-dirty ohci_hcd > usb usb2: SerialNumber: PPC-OF USB > Initializing USB Mass Storage driver... > usbcore: registered new interface driver usb-storage > USB Mass Storage support registered. > i2c /dev entries driver > rtc-m41t80 0-0068: chip found, driver version 0.05 > rtc-m41t80 0-0068: rtc core: registered m41t65 as rtc0 > ibm-iic 1ef600700.i2c: using standard (100 kHz) mode > ibm-iic 1ef600800.i2c: using standard (100 kHz) mode > at24 0-0052: 512 byte 24c04 EEPROM (writable) > ad7414 0-0048: chip found > TCP cubic registered > NET: Registered protocol family 17 > RPC: Registered udp transport module. > RPC: Registered tcp transport module. > rtc-m41t80 0-0068: setting system clock to 2009-01-05 11:33:38 UTC > (1231155218) > eth0: link is down > eth0: link is up, 100 FDX, pause enabled > IP-Config: Complete: > device=eth0, addr=137.237.178.105, mask=255.255.255.0, gw=137.237.178.1, > host=hydra_temp, domain=, nis-domain=(none), > bootserver=137.237.179.31, rootserver=137.237.179.31, rootpath= > Freeing unused kernel memory: 156k init > Checking /dev/sda1 > Checking /dev/sda2 > Checking /dev/sda3 > Checking /dev/sda4 > kjournald starting. Commit interval 5 seconds > EXT3 FS on sda3, internal journal > EXT3-fs: mounted filesystem with ordered data mode. > kjournald starting. Commit interval 5 seconds > EXT3 FS on sda1, internal journal > EXT3-fs: mounted filesystem with ordered data mode. > kjournald starting. Commit interval 5 seconds > EXT3 FS on sda2, internal journal > EXT3-fs: mounted filesystem with ordered data mode. > kjournald starting. Commit interval 5 seconds > EXT3 FS on sda4, internal journal > EXT3-fs: mounted filesystem with ordered data mode. > init started: BusyBox v1.10.4 (2008-10-27 12:52:02 EDT) > starting pid 889, tty '/dev/ttyS0': '/etc/init.d/rcS' > launcher[944]: launching /bin/craft on /dev/ttyS0 > Hydra> _______________________________________________ Linuxppc-dev mailing list Linuxppc-dev@ozlabs.org https://ozlabs.org/mailman/listinfo/linuxppc-dev
