Stephen Rothwell wrote:
> On Wed, 09 Jan 2008 15:19:13 -0500 Sean MacLennan <[EMAIL PROTECTED]> wrote:
>
>> I have split up the patches slightly differently based on Josh's comments.
>>
>> The first patch is basically the platform/44x files.
>>
>> Signed-off-by: Sean MacLennan <[EMAIL PROTECTED]>
>>
>
>
>> No comments? I really thought I would get raked over the coals for this one.
>>
>
> Ah ha! A challenge! :-)
>
I hoped somebody would respond to that ;)
>
>> +static int pika_dtm_thread(void *fpga)
>> +{
>> + extern int ad7414_get_temp(int index);
>>
>
> no externs in C code - put it in a header file.
>
I didn't know where to put this extern. It is fairly specific to this
driver, although a generic function... if that makes sense. It returns
the exact contents of the register rather than doing any conversion.
Any recommendations for a location gladly accepted.
And if anybody is wondering, the NAND code *does* work. It is commented
out because it requires u-boot 1.3.0 and most of the tacos have an
earlier u-boot. This is just a short term hack while we switch everybody
over to the new kernel.
And below has all the above mentioned fixes, except the extern.
Cheers,
Sean
Signed-off-by: Sean MacLennan <[EMAIL PROTECTED]>
---
diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig
index 66a3d8c..b3e4c35 100644
--- a/arch/powerpc/Kconfig
+++ b/arch/powerpc/Kconfig
@@ -469,7 +469,7 @@ config MCA
config PCI
bool "PCI support" if 40x || CPM2 || PPC_83xx || PPC_85xx || PPC_86xx \
|| PPC_MPC52xx || (EMBEDDED && (PPC_PSERIES || PPC_ISERIES)) \
- || PPC_PS3
+ || PPC_PS3 || 44x
default y if !40x && !CPM2 && !8xx && !PPC_83xx \
&& !PPC_85xx && !PPC_86xx
default PCI_PERMEDIA if !4xx && !CPM2 && !8xx
diff --git a/arch/powerpc/platforms/44x/Kconfig
b/arch/powerpc/platforms/44x/Kconfig
index d248013..a95409e 100644
--- a/arch/powerpc/platforms/44x/Kconfig
+++ b/arch/powerpc/platforms/44x/Kconfig
@@ -53,6 +53,19 @@ config RAINIER
help
This option enables support for the AMCC PPC440GRX evaluation board.
+config WARP
+ bool "PIKA Warp"
+ depends on 44x
+ default n
+ select 440EP
+ help
+ This option enables support for the PIKA Warp(tm) Appliance. The Warp
+ is a small computer replacement with up to 9 ports of FXO/FXS plus
VOIP
+ stations and trunks.
+
+ See http://www.pikatechnologies.com/ and follow the "PIKA for Computer
+ Telephony Developers" link for more information.
+
#config LUAN
# bool "Luan"
# depends on 44x
@@ -75,6 +88,7 @@ config 440EP
select PPC_FPU
select IBM440EP_ERR42
select IBM_NEW_EMAC_ZMII
+ select USB_ARCH_HAS_OHCI
config 440EPX
bool
diff --git a/arch/powerpc/platforms/44x/Makefile
b/arch/powerpc/platforms/44x/Makefile
index a2a0dc1..c1733c0 100644
--- a/arch/powerpc/platforms/44x/Makefile
+++ b/arch/powerpc/platforms/44x/Makefile
@@ -5,3 +5,4 @@ obj-$(CONFIG_BAMBOO) += bamboo.o
obj-$(CONFIG_SEQUOIA) += sequoia.o
obj-$(CONFIG_KATMAI) += katmai.o
obj-$(CONFIG_RAINIER) += rainier.o
+obj-$(CONFIG_WARP) += warp.o
--- /dev/null 2005-11-20 22:22:37.000000000 -0500
+++ arch/powerpc/platforms/44x/warp.c 2008-01-11 02:08:20.000000000 -0500
@@ -0,0 +1,244 @@
+/*
+ * PIKA Warp(tm) board specific routines
+ *
+ * Copyright (c) 2008 PIKA Technologies
+ * Sean MacLennan <[EMAIL PROTECTED]>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+#include <linux/init.h>
+#include <linux/of_platform.h>
+#include <linux/kthread.h>
+
+#include <asm/machdep.h>
+#include <asm/prom.h>
+#include <asm/udbg.h>
+#include <asm/time.h>
+#include <asm/uic.h>
+
+#include "44x.h"
+
+#define WARP_GPIO_BASE 0xEF600B00ULL
+
+static __initdata struct of_device_id warp_of_bus[] = {
+ { .compatible = "ibm,plb4", },
+ { .compatible = "ibm,opb", },
+ { .compatible = "ibm,ebc", },
+ {},
+};
+
+static int __init warp_device_probe(void)
+{
+ of_platform_bus_probe(NULL, warp_of_bus, NULL);
+ return 0;
+}
+machine_device_initcall(warp, warp_device_probe);
+
+static int __init warp_probe(void)
+{
+ unsigned long root = of_get_flat_dt_root();
+
+ if (!of_flat_dt_is_compatible(root, "pika,warp"))
+ return 0;
+
+ return 1;
+}
+
+define_machine(warp) {
+ .name = "Warp",
+ .probe = warp_probe,
+ .progress = udbg_progress,
+ .init_IRQ = uic_init_tree,
+ .get_irq = uic_get_irq,
+ .restart = ppc44x_reset_system,
+ .calibrate_decr = generic_calibrate_decr,
+};
+
+/* This is for the power LEDs 1 = on, 0 = off, -1 = leave alone */
+void warp_set_power_leds(int green, int red)
+{
+ static void *gpio_base = NULL;
+ unsigned leds;
+
+ if (gpio_base == NULL) {
+ gpio_base = ioremap(WARP_GPIO_BASE, 0x148);
+ if (gpio_base == NULL) {
+ printk("ERROR: Unable to remap GPIO base.\n");
+ return;
+ }
+ }
+
+ leds = readl(gpio_base + 0x100);
+
+ switch(green) {
+ case 0: leds &= ~0x80; break;
+ case 1: leds |= 0x80; break;
+ }
+ switch(red) {
+ case 0: leds &= ~0x40; break;
+ case 1: leds |= 0x40; break;
+ }
+
+ writel(leds, gpio_base + 0x100);
+}
+EXPORT_SYMBOL(warp_set_power_leds);
+
+
+static int pika_dtm_thread(void *fpga)
+{
+ extern int ad7414_get_temp(int index);
+
+ while(!kthread_should_stop()) {
+ int temp = ad7414_get_temp(0);
+
+ out_be32(fpga, temp);
+
+ set_current_state(TASK_INTERRUPTIBLE);
+ schedule_timeout(HZ);
+ }
+
+ return 0;
+}
+
+
+static int __devinit warp_fpga_init(void)
+{
+ struct device_node *np;
+ void *fpga;
+ int irq;
+ struct resource res;
+ struct task_struct *dtm_thread;
+
+ np = of_find_compatible_node(NULL, NULL, "pika,fpga");
+ if (np == NULL) {
+ printk(KERN_ERR __FILE__ ": Unable to find fpga\n");
+ return -ENOENT;
+ }
+
+ irq = irq_of_parse_and_map(np, 0);
+ if (irq == NO_IRQ) {
+ printk(KERN_ERR __FILE__ ": irq_of_parse_and_map failed\n");
+ return -EBUSY;
+ }
+
+ /* We do not call of_iomap here since it would map in the entire
+ * fpga space, which is over 8k.
+ */
+ if (of_address_to_resource(np, 0, &res)) {
+ printk(KERN_ERR __FILE__ ": Unable to get FPGA address\n");
+ return -ENOENT;
+ }
+ fpga = ioremap(res.start, 0x24);
+ if(fpga == NULL) {
+ printk(KERN_ERR __FILE__ ": Unable to map FPGA\n");
+ return -ENOENT;
+ }
+
+ /* Turn off the line LEDs */
+ out_be32(fpga + 8, 0);
+
+ dtm_thread = kthread_run(pika_dtm_thread, fpga + 0x20, "pika-dtm");
+ if (IS_ERR(dtm_thread)) {
+ iounmap(fpga);
+ printk(KERN_ERR __FILE__ ": Unable to start PIKA DTM thread\n");
+ return PTR_ERR(dtm_thread);
+ }
+
+ return 0;
+}
+device_initcall(warp_fpga_init);
+
+// SAM not yet #define NAND_FLASH
+#ifdef NAND_FLASH
+/* --- All of this code is for the NAND flash */
+
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/ndfc.h>
+
+
+#define CS_NAND_0 1 /* use chip select 1 for NAND device 0 */
+
+#define WARP_NAND_FLASH_REG_ADDR 0xD0000000UL
+#define WARP_NAND_FLASH_REG_SIZE 0x2000
+
+static struct resource warp_ndfc = {
+ .start = WARP_NAND_FLASH_REG_ADDR,
+ .end = WARP_NAND_FLASH_REG_ADDR + WARP_NAND_FLASH_REG_SIZE,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct mtd_partition nand_parts[] = {
+ {
+ .name = "nand",
+ .offset = 0,
+ .size = MTDPART_SIZ_FULL,
+ }
+};
+
+struct ndfc_controller_settings warp_ndfc_settings = {
+ .ccr_settings = (NDFC_CCR_BS(CS_NAND_0) | NDFC_CCR_ARAC1),
+ .ndfc_erpn = 0,
+};
+
+static struct ndfc_chip_settings warp_chip0_settings = {
+ .bank_settings = 0x80002222,
+};
+
+struct platform_nand_ctrl warp_nand_ctrl = {
+ .priv = &warp_ndfc_settings,
+};
+
+static struct platform_device warp_ndfc_device = {
+ .name = "ndfc-nand",
+ .id = 0,
+ .dev = {
+ .platform_data = &warp_nand_ctrl,
+ },
+ .num_resources = 1,
+ .resource = &warp_ndfc,
+};
+
+static struct nand_ecclayout nand_oob_16 = {
+ .eccbytes = 3,
+ .eccpos = { 0, 1, 2, 3, 6, 7 },
+ .oobfree = { {.offset = 8, .length = 16} }
+};
+
+static struct platform_nand_chip warp_nand_chip0 = {
+ .nr_chips = 1,
+ .chip_offset = CS_NAND_0,
+ .nr_partitions = ARRAY_SIZE(nand_parts),
+ .partitions = nand_parts,
+ .chip_delay = 50,
+ .ecclayout = &nand_oob_16,
+ .priv = &warp_chip0_settings,
+};
+
+static struct platform_device warp_nand_device = {
+ .name = "ndfc-chip",
+ .id = 0,
+ .num_resources = 1,
+ .resource = &warp_ndfc,
+ .dev = {
+ .platform_data = &warp_nand_chip0,
+ .parent = &warp_ndfc_device.dev,
+ }
+};
+
+static int warp_setup_flash(void)
+{
+ platform_device_register(&warp_ndfc_device);
+ platform_device_register(&warp_nand_device);
+
+ return 0;
+}
+device_initcall(warp_setup_flash);
+
+#endif /* NAND_FLASH */
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-dev
