This adds base support for the Katmai board, including PCI-X and
PCI-Express (but no RTC, nvram, etc... yet).
Signed-off-by: Benjamin Herrenschmidt <[EMAIL PROTECTED]>
---
As for Taishan, the bootwrapper code can be simplified. In fact,
we probably don't need to probe clocks & memsize off the chip and
just trust what uboot tells us.
arch/powerpc/boot/44x.h | 1
arch/powerpc/boot/Makefile | 7
arch/powerpc/boot/cuboot-katmai.c | 35 +++
arch/powerpc/boot/dts/katmai.dts | 392 ++++++++++++++++++++++++++++++++++++
arch/powerpc/boot/katmai.c | 64 +++++
arch/powerpc/platforms/44x/Kconfig | 12 +
arch/powerpc/platforms/44x/Makefile | 3
arch/powerpc/platforms/44x/katmai.c | 63 +++++
8 files changed, 574 insertions(+), 3 deletions(-)
Index: linux-work/arch/powerpc/platforms/44x/Kconfig
===================================================================
--- linux-work.orig/arch/powerpc/platforms/44x/Kconfig 2007-11-30
13:51:48.000000000 +1100
+++ linux-work/arch/powerpc/platforms/44x/Kconfig 2007-11-30
13:51:48.000000000 +1100
@@ -30,6 +30,14 @@ config TAISHAN
help
This option enables support for the IBM PPC440GX "Taishan" evaluation
board.
+config KATMAI
+ bool "Katmai"
+ depends on 44x
+ default n
+ select 440SPe
+ help
+ This option enables support for the AMCC PPC440SPe evaluation board.
+
#config LUAN
# bool "Luan"
# depends on 44x
@@ -74,6 +82,10 @@ config 440GX
config 440SP
bool
+config 440SPe
+ select IBM_NEW_EMAC_EMAC4
+ bool
+
# 44x errata/workaround config symbols, selected by the CPU models above
config IBM440EP_ERR42
bool
Index: linux-work/arch/powerpc/platforms/44x/Makefile
===================================================================
--- linux-work.orig/arch/powerpc/platforms/44x/Makefile 2007-11-30
13:51:48.000000000 +1100
+++ linux-work/arch/powerpc/platforms/44x/Makefile 2007-11-30
13:51:48.000000000 +1100
@@ -1,5 +1,6 @@
obj-$(CONFIG_44x) := misc_44x.o
obj-$(CONFIG_EBONY) += ebony.o
obj-$(CONFIG_TAISHAN) += taishan.o
-obj-$(CONFIG_BAMBOO) += bamboo.o
+obj-$(CONFIG_BAMBOO) += bamboo.o
obj-$(CONFIG_SEQUOIA) += sequoia.o
+obj-$(CONFIG_KATMAI) += katmai.o
Index: linux-work/arch/powerpc/boot/dts/katmai.dts
===================================================================
--- /dev/null 1970-01-01 00:00:00.000000000 +0000
+++ linux-work/arch/powerpc/boot/dts/katmai.dts 2007-11-30 14:46:02.000000000
+1100
@@ -0,0 +1,392 @@
+/*
+ * Device Tree Source for AMCC Bamboo
+ *
+ * Copyright (c) 2006, 2007 IBM Corp.
+ * Benjamin Herrenschmidt <[EMAIL PROTECTED]>
+ *
+ * Copyright (c) 2006, 2007 IBM Corp.
+ * Josh Boyer <[EMAIL PROTECTED]>
+ *
+ * FIXME: Draft only!
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ */
+
+/ {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ model = "amcc,katmai";
+ compatible = "amcc,katmai";
+ dcr-parent = <&/cpus/PowerPC,[EMAIL PROTECTED]>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,[EMAIL PROTECTED] {
+ device_type = "cpu";
+ reg = <0>;
+ clock-frequency = <0>; /* Filled in by zImage */
+ timebase-frequency = <0>; /* Filled in by zImage */
+ i-cache-line-size = <20>;
+ d-cache-line-size = <20>;
+ i-cache-size = <20000>;
+ d-cache-size = <20000>;
+ dcr-controller;
+ dcr-access-method = "native";
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0 0>; /* Filled in by zImage */
+ };
+
+ UIC0: interrupt-controller0 {
+ compatible = "ibm,uic-440spe","ibm,uic";
+ interrupt-controller;
+ cell-index = <0>;
+ dcr-reg = <0c0 009>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ };
+
+ UIC1: interrupt-controller1 {
+ compatible = "ibm,uic-440spe","ibm,uic";
+ interrupt-controller;
+ cell-index = <1>;
+ dcr-reg = <0d0 009>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ interrupts = <1e 4 1f 4>; /* cascade */
+ interrupt-parent = <&UIC0>;
+ };
+
+ UIC2: interrupt-controller2 {
+ compatible = "ibm,uic-440spe","ibm,uic";
+ interrupt-controller;
+ cell-index = <2>;
+ dcr-reg = <0e0 009>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ interrupts = <a 4 b 4>; /* cascade */
+ interrupt-parent = <&UIC0>;
+ };
+
+ UIC3: interrupt-controller3 {
+ compatible = "ibm,uic-440spe","ibm,uic";
+ interrupt-controller;
+ cell-index = <3>;
+ dcr-reg = <0f0 009>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ interrupts = <10 4 11 4>; /* cascade */
+ interrupt-parent = <&UIC0>;
+ };
+
+ SDR0: sdr {
+ compatible = "ibm,sdr-440spe";
+ dcr-reg = <00e 002>;
+ };
+
+ CPR0: cpr {
+ compatible = "ibm,cpr-440spe";
+ dcr-reg = <00c 002>;
+ };
+
+ plb {
+ compatible = "ibm,plb-440spe", "ibm,plb-440gp", "ibm,plb4";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges;
+ clock-frequency = <0>; /* Filled in by zImage */
+
+ SDRAM0: sdram {
+ compatible = "ibm,sdram-440spe", "ibm,sdram-405gp";
+ dcr-reg = <010 2>;
+ };
+
+ MAL0: mcmal {
+ compatible = "ibm,mcmal-440spe", "ibm,mcmal2";
+ dcr-reg = <180 62>;
+ num-tx-chans = <2>;
+ num-rx-chans = <1>;
+ interrupt-parent = <&MAL0>;
+ interrupts = <0 1 2 3 4>;
+ #interrupt-cells = <1>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ interrupt-map = </*TXEOB*/ 0 &UIC1 6 4
+ /*RXEOB*/ 1 &UIC1 7 4
+ /*SERR*/ 2 &UIC1 1 4
+ /*TXDE*/ 3 &UIC1 2 4
+ /*RXDE*/ 4 &UIC1 3 4>;
+ };
+
+ POB0: opb {
+ compatible = "ibm,opb-440spe", "ibm,opb-440gp",
"ibm,opb";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <00000000 4 e0000000 20000000>;
+ clock-frequency = <0>; /* Filled in by zImage */
+
+ EBC0: ebc {
+ compatible = "ibm,ebc-440spe", "ibm,ebc-440gp",
"ibm,ebc";
+ dcr-reg = <012 2>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ clock-frequency = <0>; /* Filled in by zImage */
+ ranges;
+ interrupts = <5 1>;
+ interrupt-parent = <&UIC1>;
+ };
+
+ UART0: [EMAIL PROTECTED] {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <10000200 8>;
+ virtual-reg = <a0000200>;
+ clock-frequency = <0>; /* Filled in by zImage */
+ current-speed = <1c200>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <0 4>;
+ };
+
+ UART1: [EMAIL PROTECTED] {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <10000300 8>;
+ virtual-reg = <a0000300>;
+ clock-frequency = <0>;
+ current-speed = <0>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <1 4>;
+ };
+
+
+ UART2: [EMAIL PROTECTED] {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <10000600 8>;
+ virtual-reg = <a0000600>;
+ clock-frequency = <0>;
+ current-speed = <0>;
+ interrupt-parent = <&UIC1>;
+ interrupts = <5 4>;
+ };
+
+ IIC0: [EMAIL PROTECTED] {
+ device_type = "i2c";
+ compatible = "ibm,iic-440spe", "ibm,iic-440gp",
"ibm,iic";
+ reg = <10000400 14>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <2 4>;
+ };
+
+ IIC1: [EMAIL PROTECTED] {
+ device_type = "i2c";
+ compatible = "ibm,iic-440spe", "ibm,iic-440gp",
"ibm,iic";
+ reg = <10000500 14>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <3 4>;
+ };
+
+ EMAC0: [EMAIL PROTECTED] {
+ linux,network-index = <0>;
+ device_type = "network";
+ compatible = "ibm,emac-440spe", "ibm,emac4";
+ interrupt-parent = <&UIC1>;
+ interrupts = <1c 4 1d 4>;
+ reg = <10000800 70>;
+ local-mac-address = [000000000000];
+ mal-device = <&MAL0>;
+ mal-tx-channel = <0>;
+ mal-rx-channel = <0>;
+ cell-index = <0>;
+ max-frame-size = <5dc>;
+ rx-fifo-size = <1000>;
+ tx-fifo-size = <800>;
+ phy-mode = "gmii";
+ phy-map = <00000000>;
+ has-inverted-stacr-oc;
+ has-new-stacr-staopc;
+ };
+ };
+
+ PCIX0: [EMAIL PROTECTED] {
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ compatible = "ibm,plb-pcix-440spe", "ibm,plb-pcix";
+ primary;
+ large-inbound-windows;
+ enable-msi-hole;
+ reg = <c 0ec00000 8 /* Config space access */
+ 0 0 0 /* no IACK cycles */
+ c 0ed00000 4 /* Special cycles */
+ c 0ec80000 100 /* Internal registers */
+ c 0ec80100 fc>; /* Internal messaging registers
*/
+
+ /* Outbound ranges, one memory and one IO,
+ * later cannot be changed
+ */
+ ranges = <02000000 0 80000000 0000000d 80000000 0
80000000
+ 01000000 0 00000000 0000000c 08000000 0
00010000>;
+
+ /* Inbound 2GB range starting at 0 */
+ dma-ranges = <42000000 0 0 0 0 0 80000000>;
+
+ /* This drives busses 0 to 0xf */
+ bus-range = <0 f>;
+
+ /*
+ * On Katmai, the following PCI-X interrupts signals
+ * have to be enabled via jumpers (only INTA is
+ * enabled per default):
+ *
+ * INTB: J3: 1-2
+ * INTC: J2: 1-2
+ * INTD: J1: 1-2
+ */
+ interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 1 */
+ 0800 0 0 1 &UIC1 14 8
+ 0800 0 0 2 &UIC1 13 8
+ 0800 0 0 3 &UIC1 12 8
+ 0800 0 0 4 &UIC1 11 8
+ >;
+ };
+
+ PCIE0: [EMAIL PROTECTED] {
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ compatible = "ibm,plb-pciex-440speB", "ibm,plb-pciex";
+ primary;
+ port = <0>; /* port number */
+ reg = <d 00000000 20000000 /* Config space access
*/
+ c 10000000 00001000>; /* Registers */
+ dcr-reg = <100 020>;
+ sdr-base = <300>;
+
+ /* Outbound ranges, one memory and one IO,
+ * later cannot be changed
+ */
+ ranges = <02000000 0 80000000 0000000e 00000000 0
80000000
+ 01000000 0 00000000 0000000f 80000000 0
00010000>;
+
+ /* Inbound 2GB range starting at 0 */
+ dma-ranges = <42000000 0 0 0 0 0 80000000>;
+
+ /* This drives busses 10 to 0x1f */
+ bus-range = <10 1f>;
+
+ /* Legacy interrupts (note the weird polarity). We are
+ * de-swizzling here because the numbers are actually
for
+ * port of the root complex virtual P2P bridge. But I
want
+ * to avoid putting a node for it in the tree, so the
numbers
+ * below are basically de-swizzled numbers. The real
slot is
+ * on idsel 1, so the swizzling is new_pin = (pin % 4)
+ 1
+ */
+ interrupt-map-mask = <0000 0 0 7>;
+ interrupt-map = <
+ 0000 0 0 2 &UIC3 0 4 /* swizzled int A */
+ 0000 0 0 3 &UIC3 1 4 /* swizzled int B */
+ 0000 0 0 4 &UIC3 2 4 /* swizzled int C */
+ 0000 0 0 1 &UIC3 3 4 /* swizzled int D */>;
+ };
+
+ PCIE1: [EMAIL PROTECTED] {
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ compatible = "ibm,plb-pciex-440speB", "ibm,plb-pciex";
+ primary;
+ port = <0>; /* port number */
+ reg = <d 20000000 20000000 /* Config space access
*/
+ c 10001000 00001000>; /* Registers */
+ dcr-reg = <120 020>;
+ sdr-base = <340>;
+
+ /* Outbound ranges, one memory and one IO,
+ * later cannot be changed
+ */
+ ranges = <02000000 0 80000000 0000000e 80000000 0
80000000
+ 01000000 0 00000000 0000000f 80010000 0
00010000>;
+
+ /* Inbound 2GB range starting at 0 */
+ dma-ranges = <42000000 0 0 0 0 0 80000000>;
+
+ /* This drives busses 10 to 0x1f */
+ bus-range = <20 2f>;
+
+ /* Legacy interrupts (note the weird polarity). We are
+ * de-swizzling here because the numbers are actually
for
+ * port of the root complex virtual P2P bridge. But I
want
+ * to avoid putting a node for it in the tree, so the
numbers
+ * below are basically de-swizzled numbers. The real
slot is
+ * on idsel 1, so the swizzling is new_pin = (pin % 4)
+ 1
+ */
+ interrupt-map-mask = <0000 0 0 7>;
+ interrupt-map = <
+ 0000 0 0 2 &UIC3 4 4 /* swizzled int A */
+ 0000 0 0 3 &UIC3 5 4 /* swizzled int B */
+ 0000 0 0 4 &UIC3 6 4 /* swizzled int C */
+ 0000 0 0 1 &UIC3 7 4 /* swizzled int D */>;
+ };
+
+ PCIE2: [EMAIL PROTECTED] {
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ compatible = "ibm,plb-pciex-440speB", "ibm,plb-pciex";
+ primary;
+ port = <0>; /* port number */
+ reg = <d 40000000 20000000 /* Config space access
*/
+ c 10002000 00001000>; /* Registers */
+ dcr-reg = <140 020>;
+ sdr-base = <370>;
+
+ /* Outbound ranges, one memory and one IO,
+ * later cannot be changed
+ */
+ ranges = <02000000 0 80000000 0000000f 00000000 0
80000000
+ 01000000 0 00000000 0000000f 80020000 0
00010000>;
+
+ /* Inbound 2GB range starting at 0 */
+ dma-ranges = <42000000 0 0 0 0 0 80000000>;
+
+ /* This drives busses 10 to 0x1f */
+ bus-range = <30 3f>;
+
+ /* Legacy interrupts (note the weird polarity). We are
+ * de-swizzling here because the numbers are actually
for
+ * port of the root complex virtual P2P bridge. But I
want
+ * to avoid putting a node for it in the tree, so the
numbers
+ * below are basically de-swizzled numbers. The real
slot is
+ * on idsel 1, so the swizzling is new_pin = (pin % 4)
+ 1
+ */
+ interrupt-map-mask = <0000 0 0 7>;
+ interrupt-map = <
+ 0000 0 0 2 &UIC3 8 4 /* swizzled int A */
+ 0000 0 0 3 &UIC3 9 4 /* swizzled int B */
+ 0000 0 0 4 &UIC3 a 4 /* swizzled int C */
+ 0000 0 0 1 &UIC3 b 4 /* swizzled int D */>;
+ };
+ };
+
+ chosen {
+ linux,stdout-path = "/plb/opb/[EMAIL PROTECTED]";
+ };
+};
Index: linux-work/arch/powerpc/platforms/44x/katmai.c
===================================================================
--- /dev/null 1970-01-01 00:00:00.000000000 +0000
+++ linux-work/arch/powerpc/platforms/44x/katmai.c 2007-11-30
13:51:48.000000000 +1100
@@ -0,0 +1,63 @@
+/*
+ * Katmai board specific routines
+ *
+ * Benjamin Herrenschmidt <[EMAIL PROTECTED]>
+ * Copyright 2007 IBM Corp.
+ *
+ * Based on the Bamboo code by
+ * Josh Boyer <[EMAIL PROTECTED]>
+ * Copyright 2007 IBM Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+#include <linux/init.h>
+#include <linux/of_platform.h>
+
+#include <asm/machdep.h>
+#include <asm/prom.h>
+#include <asm/udbg.h>
+#include <asm/time.h>
+#include <asm/uic.h>
+
+#include "44x.h"
+
+static struct of_device_id katmai_of_bus[] = {
+ { .compatible = "ibm,plb4", },
+ { .compatible = "ibm,opb", },
+ { .compatible = "ibm,ebc", },
+ {},
+};
+
+static int __init katmai_device_probe(void)
+{
+ if (!machine_is(katmai))
+ return 0;
+
+ of_platform_bus_probe(NULL, katmai_of_bus, NULL);
+
+ return 0;
+}
+device_initcall(katmai_device_probe);
+
+static int __init katmai_probe(void)
+{
+ unsigned long root = of_get_flat_dt_root();
+
+ if (!of_flat_dt_is_compatible(root, "amcc,katmai"))
+ return 0;
+
+ return 1;
+}
+
+define_machine(katmai) {
+ .name = "Katmai",
+ .probe = katmai_probe,
+ .progress = udbg_progress,
+ .init_IRQ = uic_init_tree,
+ .get_irq = uic_get_irq,
+ .restart = ppc44x_reset_system,
+ .calibrate_decr = generic_calibrate_decr,
+};
Index: linux-work/arch/powerpc/boot/44x.h
===================================================================
--- linux-work.orig/arch/powerpc/boot/44x.h 2007-11-30 13:51:48.000000000
+1100
+++ linux-work/arch/powerpc/boot/44x.h 2007-11-30 13:51:48.000000000 +1100
@@ -13,5 +13,6 @@
void ebony_init(void *mac0, void *mac1);
void bamboo_init(void *mac0, void *mac1);
void taishan_init(void *mac0, void *mac1);
+void katmai_init(void *mac);
#endif /* _PPC_BOOT_44X_H_ */
Index: linux-work/arch/powerpc/boot/cuboot-katmai.c
===================================================================
--- /dev/null 1970-01-01 00:00:00.000000000 +0000
+++ linux-work/arch/powerpc/boot/cuboot-katmai.c 2007-11-30
13:51:48.000000000 +1100
@@ -0,0 +1,35 @@
+/*
+ * Old U-boot compatibility for Katmai
+ *
+ * Author: Hugh Blemings <[EMAIL PROTECTED]>
+ *
+ * Copyright 2007 Hugh Blemings, IBM Corporation.
+ * Based on cuboot-ebony.c which is:
+ * Copyright 2007 David Gibson, IBM Corporation.
+ * Based on cuboot-83xx.c, which is:
+ * Copyright (c) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "stdio.h"
+#include "44x.h"
+#include "cuboot.h"
+
+#define TARGET_44x
+#include "ppcboot.h"
+
+static bd_t bd;
+
+BSS_STACK(4096);
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+ unsigned long r6, unsigned long r7)
+{
+ CUBOOT_INIT();
+
+ katmai_init(&bd.bi_enetaddr);
+}
Index: linux-work/arch/powerpc/boot/katmai.c
===================================================================
--- /dev/null 1970-01-01 00:00:00.000000000 +0000
+++ linux-work/arch/powerpc/boot/katmai.c 2007-11-30 13:51:48.000000000
+1100
@@ -0,0 +1,64 @@
+/*
+ * Copyright 2007 David Gibson, IBM Corporation.
+ *
+ * Based on earlier code:
+ * Copyright (C) Paul Mackerras 1997.
+ *
+ * Matt Porter <[EMAIL PROTECTED]>
+ * Copyright 2002-2005 MontaVista Software Inc.
+ *
+ * Eugene Surovegin <[EMAIL PROTECTED]> or <[EMAIL PROTECTED]>
+ * Copyright (c) 2003, 2004 Zultys Technologies
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+#include <stdarg.h>
+#include <stddef.h>
+#include "types.h"
+#include "elf.h"
+#include "string.h"
+#include "stdio.h"
+#include "page.h"
+#include "ops.h"
+#include "reg.h"
+#include "dcr.h"
+#include "4xx.h"
+#include "44x.h"
+
+
+extern char _dtb_start[];
+extern char _dtb_end[];
+
+static u8 *katmai_mac;
+
+
+
+static void katmai_fixups(void)
+{
+ unsigned long sysclk = 33333000;
+
+ printf("Boo !\n");
+
+ /* 440SP Clock logic is all but identical to 440GX
+ * so we just use that code for now at least
+ */
+ ibm440spe_fixup_clocks(sysclk, 6 * 1843200, 0);
+
+ ibm440spe_fixup_memsize();
+
+ dt_fixup_mac_address(0, katmai_mac);
+
+ ibm4xx_fixup_ebc_ranges("/plb/opb/ebc");
+}
+
+void katmai_init(void *mac)
+{
+ platform_ops.fixups = katmai_fixups;
+// platform_ops.exit = ibm44x_dbcr_reset; **FIXME**
+ katmai_mac = mac;
+ ft_init(_dtb_start, _dtb_end - _dtb_start, 32);
+ serial_console_init();
+}
Index: linux-work/arch/powerpc/boot/Makefile
===================================================================
--- linux-work.orig/arch/powerpc/boot/Makefile 2007-11-30 13:51:48.000000000
+1100
+++ linux-work/arch/powerpc/boot/Makefile 2007-11-30 13:51:48.000000000
+1100
@@ -38,6 +38,7 @@ BOOTCFLAGS += -I$(obj) -I$(srctree)/$(ob
$(obj)/4xx.o: BOOTCFLAGS += -mcpu=440
$(obj)/ebony.o: BOOTCFLAGS += -mcpu=440
$(obj)/taishan.o: BOOTCFLAGS += -mcpu=440
+$(obj)/katmai.o: BOOTCFLAGS += -mcpu=440
$(obj)/treeboot-walnut.o: BOOTCFLAGS += -mcpu=405
@@ -53,12 +54,13 @@ src-wlib := string.S crt0.S stdio.c main
gunzip_util.c elf_util.c $(zlib) devtree.c oflib.c ofconsole.c \
4xx.c ebony.c mv64x60.c mpsc.c mv64x60_i2c.c cuboot.c bamboo.c \
cpm-serial.c stdlib.c mpc52xx-psc.c planetcore.c uartlite.c \
- fsl-soc.c mpc8xx.c pq2.c taishan.c
+ fsl-soc.c mpc8xx.c pq2.c taishan.c katmai.c
src-plat := of.c cuboot-52xx.c cuboot-83xx.c cuboot-85xx.c holly.c \
cuboot-ebony.c treeboot-ebony.c prpmc2800.c \
ps3-head.S ps3-hvcall.S ps3.c treeboot-bamboo.c cuboot-8xx.c \
cuboot-pq2.c cuboot-sequoia.c treeboot-walnut.c cuboot-bamboo.c
\
- fixed-head.S ep88xc.c cuboot-hpc2.c ep405.c cuboot-taishan.c
+ fixed-head.S ep88xc.c cuboot-hpc2.c ep405.c cuboot-taishan.c \
+ cuboot-katmai.c
src-boot := $(src-wlib) $(src-plat) empty.c
src-boot := $(addprefix $(obj)/, $(src-boot))
@@ -163,6 +165,7 @@ image-$(CONFIG_BAMBOO) += treeImage.ba
#image-$(CONFIG_SEQUOIA) += cuImage.sequoia
image-$(CONFIG_WALNUT) += treeImage.walnut
image-$(CONFIG_TAISHAN) += cuImage.taishan
+image-$(CONFIG_KATMAI) += cuImage.katmai
endif
# For 32-bit powermacs, build the COFF and miboot images
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-dev
