On Tuesday 16 October 2007, Kumar Gala wrote:
> >> I'm willing to look into doing the port over, but would need some
> >> help testing.
> >
> > Yes, it would be greatly appreciated if you could start this
> > TQM85xx port. I
> > will of course do the testing.
>
> Ok, for the TQM85xx code in arch/ppc can I get a few things from you:
>
> 1. what processors does this actually support/run on. I'm guessing
> MPC8541, MPC8555? But not really sure
IIRC there are 4 different versions of the board:
- 8540, 8541, 8555 & 8560
> 2. can you send the results of a bd_info from u-boot on the board
I have two version available right now
8540:
U-Boot 1.3.0-rc2-g527c80f0-dirty (Oct 5 2007 - 15:57:38)
CPU: 8540, Version: 2.0, (0x80300020)
Core: E500, Version: 2.0, (0x80200020)
Clock Configuration:
CPU: 833 MHz, CCB: 333 MHz,
DDR: 166 MHz, LBC: 41 MHz
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Board: TQM8540, serial# TQM8540DCBAD7-APFBC.0204 11341240 4
PCI1: 32 bit, 33 MHz (compiled)
I2C: ready
DTT: 1 is 31 C
DRAM: 256 MB (CL=2.5)
FLASH: 32 MB
L2 cache 256KB: enabled
In: serial
Out: serial
Err: serial
Net: TSEC0, TSEC1, FEC
PS/2: No device found
Kbd: reset failed, no ACK
Type run flash_nfs to mount root filesystem over NFS
=> bdinfo
memstart = 0x00000000
memsize = 0x10000000
flashstart = 0xFE000000
flashsize = 0x02000000
flashoffset = 0x00000000
sramstart = 0x00000000
sramsize = 0x00000000
immr_base = 0xE0000000
bootflags = 0xE4013F80
intfreq = 833.333 MHz
busfreq = 333.333 MHz
ethaddr = 00:D0:93:08:12:E2
eth1addr = 00:D0:93:08:12:E3
eth2addr = 00:D0:93:08:12:E4
IP addr = 192.168.210.1
baudrate = 115200 bps
8560:
U-Boot 1.2.0-ge9792fc6 (Aug 7 2007 - 08:43:55)
CPU: 8560, Version: 2.0, (0x80700020)
Core: E500, Version: 2.0, (0x80200020)
Clock Configuration:
CPU: 833 MHz, CCB: 333 MHz,
DDR: 166 MHz, LBC: 41 MHz
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Board: TQM8560, serial# TQM8560DCBAD7-APFBC.0204 11301266 4
PCI1: 32 bit, 33 MHz (compiled)
I2C: ready
DTT: 1 is 22 C
DRAM: 256 MB (CL=2.5)
FLASH: 32 MB
L2 cache 256KB: enabled
In: serial
Out: serial
Err: serial
Net: TSEC0, TSEC1, FCC3 ETHERNET
Type run flash_nfs to mount root filesystem over NFS
Hit any key to stop autoboot: 0
=> bdinfo
memstart = 0x00000000
memsize = 0x10000000
flashstart = 0xFE000000
flashsize = 0x02000000
flashoffset = 0x00000000
sramstart = 0x00000000
sramsize = 0x00000000
immr_base = 0xE0000000
bootflags = 0x00000036
vco = 666.666 MHz
sccfreq = 166.666 MHz
brgfreq = 166.666 MHz
intfreq = 833.333 MHz
cpmfreq = 333.333 MHz
busfreq = 333.333 MHz
ethaddr = 16:CC:31:E8:8C:12
eth1addr = 16:CC:31:E8:8C:13
eth2addr = 16:CC:31:E8:8C:14
IP addr = 192.168.210.2
baudrate = 115200 bps
> 3. can you send me the results of cat /proc/iomem & /proc/ioports
> from a linux boot.
8540:
bash-3.00# cat /proc/iomem
80000000-9fffffff : PCI1 host bridge
9fff8000-9fff9fff : 0000:00:1c.1
9fffbc00-9fffbfff : 0000:00:1c.1
9fffc000-9fffdfff : 0000:00:1c.0
9ffffc00-9fffffff : 0000:00:1c.0
e0003000-e00030ff : fsl-i2c.1
e0004500-e0004507 : serial
e0004600-e0004607 : serial
e0021100-e002117f : fsl-dma.0
e0021180-e00211ff : fsl-dma.1
e0021200-e002127f : fsl-dma.2
e0021280-e00212ff : fsl-dma.3
e0024000-e0024fff : fsl-gianfar.1
e0024520-e002453f : fsl-gianfar_mdio.0
e0025000-e0025fff : fsl-gianfar.2
e0026000-e0026fff : fsl-gianfar.3
e00e1000-e00e1fff : fsl-perfmon.1
bash-3.00# cat /proc/ioports
00000000-00ffffff : PCI1 host bridge
00fffe00-00fffeff : 0000:00:1c.1
00ffff00-00ffffff : 0000:00:1c.0
8560:
-bash-3.2# cat /proc/iomem
80000000-9fffffff : PCI1 host bridge
9f7fdf00-9f7fdfff : 0000:00:1c.0
9fbfe000-9fbfefff : 0000:00:0b.1
9ffff000-9fffffff : 0000:00:0b.0
e0003000-e00030ff : fsl-i2c.1
e0021100-e002117f : fsl-dma.0
e0021180-e00211ff : fsl-dma.1
e0021200-e002127f : fsl-dma.2
e0021280-e00212ff : fsl-dma.3
e0024000-e0024fff : fsl-gianfar.1
e0024520-e002453f : fsl-gianfar_mdio.0
e0025000-e0025fff : fsl-gianfar.2
e0088400-e00884ff : fcc_pram
e0088500-e00885ff : fcc_pram
e0088600-e00886ff : fcc_pram
e0091300-e009131f : fcc_regs
e0091320-e009133f : fcc_regs
e0091340-e009135f : fcc_regs
e0091380-e009139f : fcc_regs_c
e00913a0-e00913cf : fcc_regs_c
e00913d0-e00913ff : fcc_regs_c
e0091860-e00918bf : fsl-cpm-i2c.1
e0091a00-e0091a1f : fsl-cpm-scc.1
e0091a20-e0091a3f : fsl-cpm-scc.2
e0091a40-e0091a5f : fsl-cpm-scc.3
e0091a60-e0091a7f : fsl-cpm-scc.4
e0091aa0-e0091aff : fsl-cpm-spi.1
e0091b30-e0091b3f : fsl-cpm-mcc.1
e0091b50-e0091b5f : fsl-cpm-mcc.2
e00e1000-e00e1fff : fsl-perfmon.1
-bash-3.2# cat /proc/ioports
00000000-00ffffff : PCI1 host bridge
00ff7f00-00ff7fff : 0000:00:1c.0
Thanks.
Best regards,
Stefan
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-dev
