On Fri, Nov 04, 2016 at 07:48:13AM -0700, Tony Lindgren wrote:
> * Ladislav Michl <[email protected]> [161104 03:41]:
> > All your patches on top of current Linus' git and revert of:
> > commit 87326e858448c40e32f142c0b8dcc59d7b27c641
> > Author: Tony Lindgren <[email protected]>
> > Date: Tue May 31 10:05:20 2016 -0500
> >
> > usb: musb: Remove extra PM runtime calls from 2430 glue layer
> >
> > does the trick for me (reverted patch which applies bellow). I also
> > alternatively tried to increase pm_runtime_set_autosuspend_delay up
> > to 1000 without luck.
>
> OK thanks for narrowing it down. The patch does not seem to change
> anything for me with 2430 glue layer, things work for me with and
> without it. Care to check if all hunks of the patch are needed
> for you..
>
> > diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c
> > index 451b372..a623e45 100644
> > --- a/drivers/usb/musb/omap2430.c
> > +++ b/drivers/usb/musb/omap2430.c
> > @@ -218,8 +218,13 @@ static void omap_musb_mailbox_work(struct work_struct
> > *mailbox_work)
> > {
> > struct omap2430_glue *glue = container_of(mailbox_work,
> > struct omap2430_glue, omap_musb_mailbox_work);
> > + struct musb *musb = glue_to_musb(glue);
> > + struct device *dev = musb->controller;
> >
> > + pm_runtime_get_sync(dev);
> > omap_musb_set_mailbox(glue);
> > + pm_runtime_mark_last_busy(dev);
> > + pm_runtime_put_autosuspend(dev);
> > }
> >
> > static irqreturn_t omap2430_musb_interrupt(int irq, void *__hci)
>
> ..is just the above enough..
No, does not work with only this hunk:
[ 94.980102] udlfb: wait for urb interrupted: ffffffc2 available: 0
[ 124.642456] musb_ep_program 921: broken !rx_reinit, ep2 csr 0003
[ 124.648986] musb_host_rx 1912: RX2 dma busy, csr a203
[ 124.654754] musb_host_rx 1970: Rx interrupt with no errors or packet!
[ 124.661743] musb_host_rx 1970: Rx interrupt with no errors or packet!
[ 124.668762] musb_host_rx 1970: Rx interrupt with no errors or packet!
[ 124.675720] musb_host_rx 1970: Rx interrupt with no errors or packet!
[ 124.682830] musb_ep_program 921: broken !rx_reinit, ep2 csr 0003
[ 124.689178] musb_host_rx 1970: Rx interrupt with no errors or packet!
[ 124.696105] musb_host_rx 1970: Rx interrupt with no errors or packet!
[ 124.772552] udlfb: released /dev/fb0 user=1 count=0
> > @@ -289,6 +294,16 @@ static int omap2430_musb_init(struct musb *musb)
> > phy_init(musb->phy);
> > phy_power_on(musb->phy);
> >
> > + /*
> > + * Enable runtime PM for musb parent (this driver). We can't
> > + * do it earlier as struct musb is not yet allocated and we
> > + * need to touch the musb registers for runtime PM.
> > + */
> > + pm_runtime_enable(glue->dev);
> > + status = pm_runtime_get_sync(glue->dev);
> > + if (status < 0)
> > + goto err1;
> > +
> > l = musb_readl(musb->mregs, OTG_INTERFSEL);
> >
> > if (data->interface_type == MUSB_INTERFACE_UTMI) {
> > @@ -312,7 +327,11 @@ static int omap2430_musb_init(struct musb *musb)
> > if (glue->status != MUSB_UNKNOWN)
> > omap_musb_set_mailbox(glue);
> >
> > + pm_runtime_put(glue->dev);
> > return 0;
> > +
> > +err1:
> > + return status;
> > }
> >
> > static void omap2430_musb_enable(struct musb *musb)
> > @@ -512,10 +531,6 @@ static int omap2430_probe(struct platform_device *pdev)
> > goto err2;
> > }
> >
> > - pm_runtime_enable(glue->dev);
> > - pm_runtime_use_autosuspend(glue->dev);
> > - pm_runtime_set_autosuspend_delay(glue->dev, 100);
> > -
> > ret = platform_device_add(musb);
> > if (ret) {
> > dev_err(&pdev->dev, "failed to register musb device\n");
> > @@ -538,7 +553,6 @@ static int omap2430_remove(struct platform_device *pdev)
> > pm_runtime_get_sync(glue->dev);
> > platform_device_unregister(glue->musb);
> > pm_runtime_put_sync(glue->dev);
> > - pm_runtime_dont_use_autosuspend(glue->dev);
> > pm_runtime_disable(glue->dev);
> >
> > return 0;
>
> ..or are these init changes needed too?
Yes, also tried to move pm_runtime_use_autosuspend into omap2430_musb_init
and drop omap_musb_mailbox_work changes, but that does not work either.
ladis
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
