On 6/21/2016 7:26 PM, Bruno Herrera wrote:
> Signed-off-by: Bruno Herrera <bruherr...@gmail.com>
Please add a commit message describing the purpose of your changes,
some information about the platform you're adding, and the special
handling of the GGPIO.
> ---
> drivers/usb/dwc2/core.c | 18 ++++++++++++++++++
> drivers/usb/dwc2/core.h | 5 +++++
> drivers/usb/dwc2/hcd.c | 12 +++++++++++-
> drivers/usb/dwc2/hw.h | 2 ++
> drivers/usb/dwc2/platform.c | 37 +++++++++++++++++++++++++++++++++++++
> 5 files changed, 73 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/usb/dwc2/core.c b/drivers/usb/dwc2/core.c
> index 4135a5f..83fbed6 100644
> --- a/drivers/usb/dwc2/core.c
> +++ b/drivers/usb/dwc2/core.c
> @@ -1276,6 +1276,23 @@ static void dwc2_set_param_hibernation(struct
> dwc2_hsotg *hsotg,
> hsotg->core_params->hibernation = val;
> }
>
> +static void dwc2_set_param_stm32_powerdown(struct dwc2_hsotg *hsotg,
> + int val)
> +{
> + if (DWC2_OUT_OF_BOUNDS(val, 0, 1)) {
> + if (val >= 0) {
> + dev_err(hsotg->dev,
> + "'%d' invalid for parameter power down\n",
> + val);
> + dev_err(hsotg->dev, "power down must be 0 or 1\n");
> + }
> + val = 0;
> + dev_dbg(hsotg->dev, "Setting power down to %d\n", val);
> + }
> +
> + hsotg->core_params->stm32_powerdown = val;
> +}
> +
> /*
> * This function is called during module intialization to pass module
> parameters
> * for the DWC_otg core.
> @@ -1323,6 +1340,7 @@ void dwc2_set_parameters(struct dwc2_hsotg *hsotg,
> dwc2_set_param_uframe_sched(hsotg, params->uframe_sched);
> dwc2_set_param_external_id_pin_ctl(hsotg, params->external_id_pin_ctl);
> dwc2_set_param_hibernation(hsotg, params->hibernation);
> + dwc2_set_param_stm32_powerdown(hsotg, params->stm32_powerdown);
> }
>
> /*
> diff --git a/drivers/usb/dwc2/core.h b/drivers/usb/dwc2/core.h
> index 3c58d63..d3e4fcb 100644
> --- a/drivers/usb/dwc2/core.h
> +++ b/drivers/usb/dwc2/core.h
> @@ -386,6 +386,10 @@ enum dwc2_ep0_state {
> * needed.
> * 0 - No (default)
> * 1 - Yes
> + * @stm32_powerdown: Enable STM32 specific USB FS transceiver power down
> + * control.
> + * 0 = USB FS transceiver disabled (default)
> + * 1 = USB FS transceiver enabled
> *
> * The following parameters may be specified when starting the module. These
> * parameters define how the DWC_otg controller should be configured. A
> @@ -426,6 +430,7 @@ struct dwc2_core_params {
> int uframe_sched;
> int external_id_pin_ctl;
> int hibernation;
> + int stm32_powerdown;
> };
>
> /**
> diff --git a/drivers/usb/dwc2/hcd.c b/drivers/usb/dwc2/hcd.c
> index 2df3d04..4f9bb93 100644
> --- a/drivers/usb/dwc2/hcd.c
> +++ b/drivers/usb/dwc2/hcd.c
> @@ -118,7 +118,7 @@ static void dwc2_init_fs_ls_pclk_sel(struct dwc2_hsotg
> *hsotg)
>
> static int dwc2_fs_phy_init(struct dwc2_hsotg *hsotg, bool select_phy)
> {
> - u32 usbcfg, i2cctl;
> + u32 usbcfg, usbgpio, i2cctl;
The convention in this driver would be to just call 'usbgpio' -> 'ggpio'
> int retval = 0;
>
> /*
> @@ -142,6 +142,16 @@ static int dwc2_fs_phy_init(struct dwc2_hsotg *hsotg,
> bool select_phy)
> return retval;
> }
> }
> +
> + if (hsotg->core_params->stm32_powerdown > 0) {
> + dev_dbg(hsotg->dev, "STM32 FS PHY enabling
> transceiver\n");
> + /* STM32 uses the GGPIO register as general core
> + * configuration register.
> + */
> + usbgpio = dwc2_readl(hsotg->regs + GGPIO);
> + usbgpio |= STM32_OTG_GCCFG_PWRDWN;
> + dwc2_writel(usbgpio, hsotg->regs + GGPIO);
> + }
> }
>
> /*
> diff --git a/drivers/usb/dwc2/hw.h b/drivers/usb/dwc2/hw.h
> index 281b57b..d5f9294 100644
> --- a/drivers/usb/dwc2/hw.h
> +++ b/drivers/usb/dwc2/hw.h
> @@ -224,6 +224,8 @@
>
> #define GPVNDCTL HSOTG_REG(0x0034)
> #define GGPIO HSOTG_REG(0x0038)
> +#define STM32_OTG_GCCFG_PWRDWN (1 << 16)
> +
Also, bitfields for GGPIO should be named: GGPIO_xxx
> #define GUID HSOTG_REG(0x003c)
> #define GSNPSID HSOTG_REG(0x0040)
> #define GHWCFG1 HSOTG_REG(0x0044)
> diff --git a/drivers/usb/dwc2/platform.c b/drivers/usb/dwc2/platform.c
> index fc6f525..d806b94 100644
> --- a/drivers/usb/dwc2/platform.c
> +++ b/drivers/usb/dwc2/platform.c
> @@ -84,6 +84,7 @@ static const struct dwc2_core_params params_hi6220 = {
> .uframe_sched = 0,
> .external_id_pin_ctl = -1,
> .hibernation = -1,
> + .stm32_powerdown = 0,
You can probably just leave this out of unrelated configurations since
it will default to 0.
Regards,
John
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
