From: JackyChou <jackyc...@asix.com.tw>
Add a new PID 0x7843 to the driver.
Let the new products be able to set up 3 serial ports with the driver.
Signed-off-by: JackyChou <jackyc...@asix.com.tw>
---
drivers/usb/serial/mos7840.c | 26 ++++++++++++++++++--------
1 file changed, 18 insertions(+), 8 deletions(-)
diff --git a/drivers/usb/serial/mos7840.c b/drivers/usb/serial/mos7840.c
index b42bad85097a..7667b22fa2f7 100644
--- a/drivers/usb/serial/mos7840.c
+++ b/drivers/usb/serial/mos7840.c
@@ -94,6 +94,7 @@
/* The native mos7840/7820 component */
#define USB_VENDOR_ID_MOSCHIP 0x9710
#define MOSCHIP_DEVICE_ID_7840 0x7840
+#define MOSCHIP_DEVICE_ID_7843 0x7843
#define MOSCHIP_DEVICE_ID_7820 0x7820
#define MOSCHIP_DEVICE_ID_7810 0x7810
/* The native component can have its vendor/device id's overridden
@@ -176,6 +177,7 @@ enum mos7840_flag {
static const struct usb_device_id id_table[] = {
{USB_DEVICE(USB_VENDOR_ID_MOSCHIP, MOSCHIP_DEVICE_ID_7840)},
+ {USB_DEVICE(USB_VENDOR_ID_MOSCHIP, MOSCHIP_DEVICE_ID_7843)},
{USB_DEVICE(USB_VENDOR_ID_MOSCHIP, MOSCHIP_DEVICE_ID_7820)},
{USB_DEVICE(USB_VENDOR_ID_MOSCHIP, MOSCHIP_DEVICE_ID_7810)},
{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USO9ML2_2)},
@@ -298,7 +300,7 @@ static int mos7840_set_uart_reg(struct usb_serial_port
*port, __u16 reg,
val = val & 0x00ff;
/* For the UART control registers, the application number need
to be Or'ed */
- if (port->serial->num_ports == 4) {
+ if (port->serial->num_ports == 4 || port->serial->num_ports == 3) {
val |= ((__u16)port->port_number + 1) << 8;
} else {
if (port->port_number == 0) {
@@ -332,7 +334,7 @@ static int mos7840_get_uart_reg(struct usb_serial_port
*port, __u16 reg,
return -ENOMEM;
/* Wval is same as application number */
- if (port->serial->num_ports == 4) {
+ if (port->serial->num_ports == 4 || port->serial->num_ports == 3) {
Wval = ((__u16)port->port_number + 1) << 8;
} else {
if (port->port_number == 0) {
@@ -2071,9 +2073,12 @@ static int mos7840_probe(struct usb_serial *serial,
VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT);
/* For a MCS7840 device GPIO0 must be set to 1 */
- if (buf[0] & 0x01)
- device_type = MOSCHIP_DEVICE_ID_7840;
- else if (mos7810_check(serial))
+ if (buf[0] & 0x01) {
+ if (product == MOSCHIP_DEVICE_ID_7843)
+ device_type = MOSCHIP_DEVICE_ID_7843;
+ else
+ device_type = MOSCHIP_DEVICE_ID_7840;
+ } else if (mos7810_check(serial))
device_type = MOSCHIP_DEVICE_ID_7810;
else
device_type = MOSCHIP_DEVICE_ID_7820;
@@ -2091,7 +2096,10 @@ static int mos7840_calc_num_ports(struct usb_serial
*serial,
int device_type = (unsigned long)usb_get_serial_data(serial);
int num_ports;
- num_ports = (device_type >> 4) & 0x000F;
+ if (device_type == MOSCHIP_DEVICE_ID_7843)
+ num_ports = 3;
+ else
+ num_ports = (device_type >> 4) & 0x000F;
/*
* num_ports is currently never zero as device_type is one of
@@ -2146,7 +2154,8 @@ static int mos7840_port_probe(struct usb_serial_port
*port)
mos7840_port->SpRegOffset = 0x0;
mos7840_port->ControlRegOffset = 0x1;
mos7840_port->DcrRegOffset = 0x4;
- } else if ((mos7840_port->port_num == 2) && (serial->num_ports == 4)) {
+ } else if ((mos7840_port->port_num == 2) &&
+ ((serial->num_ports == 4) || (serial->num_ports == 3))) {
mos7840_port->SpRegOffset = 0x8;
mos7840_port->ControlRegOffset = 0x9;
mos7840_port->DcrRegOffset = 0x16;
@@ -2154,7 +2163,8 @@ static int mos7840_port_probe(struct usb_serial_port
*port)
mos7840_port->SpRegOffset = 0xa;
mos7840_port->ControlRegOffset = 0xb;
mos7840_port->DcrRegOffset = 0x19;
- } else if ((mos7840_port->port_num == 3) && (serial->num_ports == 4)) {
+ } else if ((mos7840_port->port_num == 3) &&
+ ((serial->num_ports == 4) || (serial->num_ports == 3))) {
mos7840_port->SpRegOffset = 0xa;
mos7840_port->ControlRegOffset = 0xb;
mos7840_port->DcrRegOffset = 0x19;
--
2.17.1
