In _scsih_sas_host_add, the number of HBA phys are determined and then
later used to allocate an array of struct _sas_phy's. If the routine
sets ioc->sas_hba.num_phys, but then fails to allocate the
ioc->sas_hba.phy array (by kcalloc error or other intermediate
error/exit path), ioc->sas_hba is left in a dangerous state: all readers
of ioc->sas_hba.phy[] do so by indexing it from 0..ioc->sas_hba.num_phys
without checking that the space was ever allocated.
Modify _scsih_sas_host_add to set ioc->sas_hba.num_phys only after
successfully allocating ioc->sas_hba.phy[].
Signed-off-by: Joe Lawrence <joe.lawre...@stratus.com>
---
drivers/scsi/mpt3sas/mpt3sas_scsih.c | 20 +++++++++++---------
1 file changed, 11 insertions(+), 9 deletions(-)
diff --git a/drivers/scsi/mpt3sas/mpt3sas_scsih.c
b/drivers/scsi/mpt3sas/mpt3sas_scsih.c
index f2139e5604a3..6e36d20c9e0b 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_scsih.c
+++ b/drivers/scsi/mpt3sas/mpt3sas_scsih.c
@@ -4893,13 +4893,22 @@ _scsih_sas_host_add(struct MPT3SAS_ADAPTER *ioc)
u16 ioc_status;
u16 sz;
u8 device_missing_delay;
+ u8 num_phys;
- mpt3sas_config_get_number_hba_phys(ioc, &ioc->sas_hba.num_phys);
- if (!ioc->sas_hba.num_phys) {
+ mpt3sas_config_get_number_hba_phys(ioc, &num_phys);
+ if (!num_phys) {
pr_err(MPT3SAS_FMT "failure at %s:%d/%s()!\n",
ioc->name, __FILE__, __LINE__, __func__);
return;
}
+ ioc->sas_hba.phy = kcalloc(num_phys,
+ sizeof(struct _sas_phy), GFP_KERNEL);
+ if (!ioc->sas_hba.phy) {
+ pr_err(MPT3SAS_FMT "failure at %s:%d/%s()!\n",
+ ioc->name, __FILE__, __LINE__, __func__);
+ goto out;
+ }
+ ioc->sas_hba.num_phys = num_phys;
/* sas_iounit page 0 */
sz = offsetof(Mpi2SasIOUnitPage0_t, PhyData) + (ioc->sas_hba.num_phys *
@@ -4959,13 +4968,6 @@ _scsih_sas_host_add(struct MPT3SAS_ADAPTER *ioc)
MPI2_SASIOUNIT1_REPORT_MISSING_TIMEOUT_MASK;
ioc->sas_hba.parent_dev = &ioc->shost->shost_gendev;
- ioc->sas_hba.phy = kcalloc(ioc->sas_hba.num_phys,
- sizeof(struct _sas_phy), GFP_KERNEL);
- if (!ioc->sas_hba.phy) {
- pr_err(MPT3SAS_FMT "failure at %s:%d/%s()!\n",
- ioc->name, __FILE__, __LINE__, __func__);
- goto out;
- }
for (i = 0; i < ioc->sas_hba.num_phys ; i++) {
if ((mpt3sas_config_get_phy_pg0(ioc, &mpi_reply, &phy_pg0,
i))) {
--
1.8.3.1
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
