On Thu, 2010-12-30 at 20:38 +0100, Guennadi Liakhovetski wrote:
> On Sat, 18 Dec 2010, Guennadi Liakhovetski wrote:
>
> > Alberto
> >
> > it would be slowly on the time to address my comments and submit updates.
> > While at it, also, please update the subject - you probably meant "YUV422"
> > or "YUV444" there, also below:
>
> Ok, I'm dropping this patch
>
> Alberto, I've applied and pushed your other 2 patches from this series,
> but I've dropped this one. The reason is not (only), that you didn't reply
> to my two last mails with update-requests. But because of that I took the
> time today to look deeper into detail at this patch. And as a result, I
> don't think it is correct.
>
> Currently the mx3_camera driver transfers data from video clients (camera
> sensors) only in one mode - as raw data, 1-to-1. This is extablished in
> the way, how it creates format translation tables during the initial
> negotiation with client drivers in mx3_camera_get_formats().
>
> Your patch is trying to add support for specific modes on CSI, but is only
> doing this in the transfer part of the driver, and not in the negotiation
> part. So, if you really need native support for various pixel formats,
> this is a wrong way to do this. If you only want to transfer data from
> your sensor into RAM and the current driver is failing for you, then this
> is a wrong way to do this, and the bug has to be found and fixed, while
> maintaining the present pass-through only model.
>
> Thanks
> Guennadi
Really sorry Guennadi!
My mailer didn't filtered this thread successfully and so I missed your
comments! Damn!
I'll go deeper on your suggestions in these days and hope to find a good
solution.
Thank you,
Alberto!
>
> > On Wed, 1 Dec 2010, Guennadi Liakhovetski wrote:
> >
> > > On Sun, 28 Nov 2010, Alberto Panizzo wrote:
> > >
> > > > This patch is tested and works with the OV2640 camera that output
> > > > YUV422 (UYVY) and RGB565 data.
> > > >
> > > > The YUV422 format is managed to be converted in IPU internal YUV444
> > > > format
> > > > so this stream could be used in the future to feed directly other IPU
> > > > blocks.
> > > > The RGB565 format is managed as GENERIC and can be moved only from CSI
> > > > to memory.
> > > >
> > > > Signed-off-by: Alberto Panizzo <maramaopercheseimo...@gmail.com>
> > > > ---
> > > >
> > > > Before applying, please give me feedback if this break in some way other
> > > > pixel formats!
> > > >
> > > >
> > > > drivers/media/video/mx3_camera.c | 126
> > > > +++++++++++++++++++++++++++++++++-----
> > > > 1 files changed, 110 insertions(+), 16 deletions(-)
> > > >
> > > > diff --git a/drivers/media/video/mx3_camera.c
> > > > b/drivers/media/video/mx3_camera.c
> > > > index 29c5fc3..6811d6f 100644
> > > > --- a/drivers/media/video/mx3_camera.c
> > > > +++ b/drivers/media/video/mx3_camera.c
> > > > @@ -55,6 +55,31 @@
> > > > #define CSI_SENS_CONF_EXT_VSYNC_SHIFT 15
> > > > #define CSI_SENS_CONF_DIVRATIO_SHIFT 16
> > > >
> > > > +/*
> > > > + * IPU support the following data formatting (44.1.1.3 Data Flows and
> > > > Formats):
> > > > + * 1 YUV 4:4:4 or RGBâ8 bits per color component
> > > > + * 2 YUV 4:4:4 or RGBâ10 bits per color component
> >
> > don't know what characters are those. Please, replace with ASCII.
> >
> > Thanks
> > Guennadi
> >
> > > > + * 3 Generic data (from sensor to the system memory only)
> > > > + * The formats 1 and 2 are aligned in words of 32 bits, 3 is free and
> > > > not
> > > > + * recognized by IPU blocks.
> > > > + *
> > > > + * Taking the value of SENS_DATA_FORMAT and DATA_WIDTH, the CSI tries
> > > > to
> > > > + * align (or rearrange) the sampled data to fit the IPU supported
> > > > formats
> > > > + * as follows:
> > > > + * - CSI_SENS_CONF_DATA_FMT_RGB_YUV444: It consider the pixel as a
> > > > sequence of
> > > > + * 3 components of width DATA_WIDTH aligning these to a 32 bit
> > > > word.
> > > > + * The CSI output in this case can feed other IPU blocks.
> > > > + * - CSI_SENS_CONF_DATA_FMT_YUV422: It consider the pixel as a
> > > > sequence of
> > > > + * 2 components of width DATA_WIDTH were the first is the
> > > > alternating U V
> > >
> > > s/were/where/
> > >
> > > > + * components and the second is Y. It construct the YUV444 word
> > > > repeating
> > > > + * the previous U, V samples aligning the results to a 32 bit word.
> > > > + * The CSI output in this case can feed other IPU blocks.
> > > > + * - CSI_SENS_CONF_DATA_FMT_BAYER: No rework is performed in this case.
> > > > + * The sensor data is given as is, considering _every sample_ as a
> > > > pixel
> > > > + * data. This format (combined with the GENERIC IPU pixel formats)
> > > > can
> > > > + * carry all the other sensor pixel formats to the system memory.
> > > > + * The CSI output in this case _can not_ feed other IPU blocks.
> > > > + */
> > > > #define CSI_SENS_CONF_DATA_FMT_RGB_YUV444 (0UL <<
> > > > CSI_SENS_CONF_DATA_FMT_SHIFT)
> > > > #define CSI_SENS_CONF_DATA_FMT_YUV422 (2UL <<
> > > > CSI_SENS_CONF_DATA_FMT_SHIFT)
> > > > #define CSI_SENS_CONF_DATA_FMT_BAYER (3UL <<
> > > > CSI_SENS_CONF_DATA_FMT_SHIFT)
> > > > @@ -323,14 +348,12 @@ static enum pixel_fmt fourcc_to_ipu_pix(__u32
> > > > fourcc)
> > > > {
> > > > /* Add more formats as need arises and test possibilities
> > > > appear... */
> > > > switch (fourcc) {
> > > > - case V4L2_PIX_FMT_RGB565:
> > > > - return IPU_PIX_FMT_RGB565;
> > > > case V4L2_PIX_FMT_RGB24:
> > > > return IPU_PIX_FMT_RGB24;
> > > > + case V4L2_PIX_FMT_UYVY:
> > > > + return IPU_PIX_FMT_UYVY;
> > > > + case V4L2_PIX_FMT_RGB565:
> > > > case V4L2_PIX_FMT_RGB332:
> > > > - return IPU_PIX_FMT_RGB332;
> > > > - case V4L2_PIX_FMT_YUV422P:
> > > > - return IPU_PIX_FMT_YVU422P;
> > > > default:
> > > > return IPU_PIX_FMT_GENERIC;
> > > > }
> > >
> > > Ok, so far mx3_camera has only been used with mt9m022 and mt9t031 sensors
> > > (from what I can see in the mainline), both are bayer. It can also work
> > > with monochrome cameras, and that would be the IPU_PIX_FMT_GENERIC case
> > > too. So, I wouldn't mind removing the rest, and only adding / fixing what
> > > you've now tested / implemented with your omnivision sensor. If anyone is
> > > using mx3_camera with any other formats and thinks, that they work -
> > > please, shout now. I'll probably also post a separate mail with this
> > > warning.
> > >
> > > > @@ -358,9 +381,25 @@ static void mx3_videobuf_queue(struct
> > > > videobuf_queue *vq,
> > > >
> > > > /* This is the configuration of one sg-element */
> > > > video->out_pixel_fmt = fourcc_to_ipu_pix(fourcc);
> > > > - video->out_width = icd->user_width;
> > > > - video->out_height = icd->user_height;
> > > > - video->out_stride = icd->user_width;
> > > > +
> > > > + if (video->out_pixel_fmt == IPU_PIX_FMT_GENERIC) {
> > > > + /*
> > > > + * IPU_PIX_FMT_GENERIC transport bytes, not pixels. So
> > > > convert
> > > > + * video->out_width and stride to the correct unit.
> > > > + */
> > > > + int bytes_per_line =
> > > > soc_mbus_bytes_per_line(icd->user_width,
> > > > +
> > > > icd->current_fmt->host_fmt);
> > > > + BUG_ON(bytes_per_line <= 0);
> > > > +
> > > > + video->out_width = bytes_per_line;
> > > > + video->out_height = icd->user_height;
> > > > + video->out_stride = bytes_per_line;
> > > > + } else {
> > > > + /* For IPU known formats the pixel unit is OK */
> > > > + video->out_width = icd->user_width;
> > > > + video->out_height = icd->user_height;
> > > > + video->out_stride = icd->user_width;
> > > > + }
> > > >
> > > > #ifdef DEBUG
> > > > /* helps to see what DMA actually has written */
> > > > @@ -730,18 +769,68 @@ static int mx3_camera_get_formats(struct
> > > > soc_camera_device *icd, unsigned int id
> > > > if (xlate) {
> > > > xlate->host_fmt = fmt;
> > > > xlate->code = code;
> > > > + dev_dbg(dev, "Providing format %c%c%c%c in pass-through
> > > > mode\n",
> > > > + (xlate->host_fmt->fourcc >> (0*8)) & 0xFF,
> > > > + (xlate->host_fmt->fourcc >> (1*8)) & 0xFF,
> > > > + (xlate->host_fmt->fourcc >> (2*8)) & 0xFF,
> > > > + (xlate->host_fmt->fourcc >> (3*8)) & 0xFF);
> > > > xlate++;
> > > > - dev_dbg(dev, "Providing format %x in pass-through
> > > > mode\n",
> > > > - xlate->host_fmt->fourcc);
> > >
> > > make it even simpler: s/xlate->host_fmt/fmt/g
> > >
> > > > }
> > > >
> > > > return formats;
> > > > }
> > > >
> > > > +static int samples_per_pixel(enum v4l2_mbus_pixelcode mcode)
> > > > +{
> > > > + switch (mcode) {
> > > > + case V4L2_MBUS_FMT_YUYV8_2X8:
> > > > + case V4L2_MBUS_FMT_YVYU8_2X8:
> > > > + case V4L2_MBUS_FMT_VYUY8_2X8:
> > > > + case V4L2_MBUS_FMT_YVYU10_2X10:
> > > > + case V4L2_MBUS_FMT_YUYV10_2X10:
> > > > + case V4L2_MBUS_FMT_RGB444_2X8_PADHI_LE:
> > > > + case V4L2_MBUS_FMT_RGB444_2X8_PADHI_BE:
> > > > + case V4L2_MBUS_FMT_RGB555_2X8_PADHI_LE:
> > > > + case V4L2_MBUS_FMT_RGB555_2X8_PADHI_BE:
> > > > + case V4L2_MBUS_FMT_RGB565_2X8_LE:
> > > > + case V4L2_MBUS_FMT_RGB565_2X8_BE:
> > > > + case V4L2_MBUS_FMT_BGR565_2X8_LE:
> > > > + case V4L2_MBUS_FMT_BGR565_2X8_BE:
> > > > + return 2;
> > > > + case V4L2_MBUS_FMT_SBGGR8_1X8:
> > > > + case V4L2_MBUS_FMT_SBGGR10_1X10:
> > > > + case V4L2_MBUS_FMT_GREY8_1X8:
> > > > + case V4L2_MBUS_FMT_Y10_1X10:
> > > > + case V4L2_MBUS_FMT_SBGGR10_2X8_PADHI_LE:
> > > > + case V4L2_MBUS_FMT_SBGGR10_2X8_PADHI_BE:
> > >
> > > Are these two really 1 sample per pixel?
> > >
> > > > + case V4L2_MBUS_FMT_SGRBG8_1X8:
> > > > + return 1;
> > > > + default:
> > > > + /* Add other pixel codes as needed */
> > > > + return 0;
> > > > + }
> > > > +}
> > >
> > > Let's just do the following:
> > >
> > > s32 soc_mbus_samples_per_pixel(const struct soc_mbus_pixelfmt *mf)
> > > {
> > > switch (mf->packing) {
> > > case SOC_MBUS_PACKING_NONE:
> > > case SOC_MBUS_PACKING_EXTEND16:
> > > return 1;
> > > case SOC_MBUS_PACKING_2X8_PADHI:
> > > case SOC_MBUS_PACKING_2X8_PADLO:
> > > return 2;
> > > }
> > > return -EINVAL;
> > > }
> > > EXPORT_SYMBOL(soc_mbus_samples_per_pixel);
> > >
> > > in drivers/media/video/soc_mediabus.c, agree?
> > >
> > > > +
> > > > static void configure_geometry(struct mx3_camera_dev *mx3_cam,
> > > > - unsigned int width, unsigned int height)
> > > > + unsigned int width, unsigned int height,
> > > > + enum v4l2_mbus_pixelcode code)
> > > > {
> > > > u32 ctrl, width_field, height_field;
> > > > + const struct soc_mbus_pixelfmt *fmt;
> > > > +
> > > > + fmt = soc_mbus_get_fmtdesc(code);
> > > > + BUG_ON(!fmt);
> > > > +
> > > > + if (fourcc_to_ipu_pix(fmt->fourcc) == IPU_PIX_FMT_GENERIC) {
> > > > + /*
> > > > + * As we don't have an IPU native format, the CSI will
> > > > be
> > > > + * configured to output BAYER and here we need to
> > > > convert
> > > > + * geometry unit from pixels to samples.
> > > > + * TODO: Support vertical down sampling (YUV420)
> > > > + */
> > > > + width = width * samples_per_pixel(code);
> > > > + BUG_ON(!width);
> > > > + }
> > >
> > > width *= soc_mbus_samples_per_pixel(fmt);
> > > BUG_ON((int)width < 0);
> > >
> > > >
> > > > /* Setup frame size - this cannot be changed on-the-fly... */
> > > > width_field = width - 1;
> > > > @@ -850,7 +939,7 @@ static int mx3_camera_set_crop(struct
> > > > soc_camera_device *icd,
> > > > return ret;
> > > > }
> > > >
> > > > - configure_geometry(mx3_cam, mf.width, mf.height);
> > > > + configure_geometry(mx3_cam, mf.width, mf.height,
> > > > mf.code);
> > > > }
> > > >
> > > > dev_dbg(icd->dev.parent, "Sensor cropped %dx%d\n",
> > > > @@ -893,7 +982,7 @@ static int mx3_camera_set_fmt(struct
> > > > soc_camera_device *icd,
> > > > * mxc_v4l2_s_fmt()
> > > > */
> > > >
> > > > - configure_geometry(mx3_cam, pix->width, pix->height);
> > > > + configure_geometry(mx3_cam, pix->width, pix->height,
> > > > xlate->code);
> > > >
> > > > mf.width = pix->width;
> > > > mf.height = pix->height;
> > > > @@ -1112,10 +1201,15 @@ static int mx3_camera_set_bus_param(struct
> > > > soc_camera_device *icd, __u32 pixfmt)
> > > > (3 << CSI_SENS_CONF_DATA_FMT_SHIFT) |
> > > > (3 << CSI_SENS_CONF_DATA_WIDTH_SHIFT));
> > > >
> > > > - /* TODO: Support RGB and YUV formats */
> > > > + /* TODO: Support RGB_YUV444 formats */
> > > >
> > > > - /* This has been set in mx3_camera_activate(), but we clear it
> > > > above */
> > > > - sens_conf |= CSI_SENS_CONF_DATA_FMT_BAYER;
> > > > + switch (xlate->code) {
> > > > + case V4L2_MBUS_FMT_UYVY8_2X8:
> > > > + sens_conf |= CSI_SENS_CONF_DATA_FMT_YUV422;
> > > > + break;
> > > > + default:
> > > > + sens_conf |= CSI_SENS_CONF_DATA_FMT_BAYER;
> > > > + }
> > > >
> > > > if (common_flags & SOCAM_PCLK_SAMPLE_FALLING)
> > > > sens_conf |= 1 << CSI_SENS_CONF_PIX_CLK_POL_SHIFT;
> > > > --
> > > > 1.6.3.3
> > >
> > > If after all the above changed your set up still works, we're cool!;)
> > >
> > > Thanks
> > > Guennadi
> > > ---
> > > Guennadi Liakhovetski, Ph.D.
> > > Freelance Open-Source Software Developer
> > > http://www.open-technology.de/
> > >
> >
> > ---
> > Guennadi Liakhovetski, Ph.D.
> > Freelance Open-Source Software Developer
> > http://www.open-technology.de/
> >
>
> ---
> Guennadi Liakhovetski, Ph.D.
> Freelance Open-Source Software Developer
> http://www.open-technology.de/
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majord...@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
