BeagleBoard-X15 has capability for a fan and has an onboard TMP102
temperature sensor as well. This allows us to create a new thermal
zone (called, un-imaginatively "board"), and allows us to use some
active cooling as temperatures start edge upward in the system by
creating a new alert temperature (emperically 50C) for cpu.
NOTE: Fan is NOT mounted by default on the platform, in such a case,
all we end up doing is switch on a regulator and leak very minimal
current.
Signed-off-by: Nishanth Menon <n...@ti.com>
---
arch/arm/boot/dts/am57xx-beagle-x15.dts | 49 +++++++++++++++++++++++++++++++
1 file changed, 49 insertions(+)
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts
b/arch/arm/boot/dts/am57xx-beagle-x15.dts
index 41642fe770a1..6a3621c23017 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15.dts
+++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts
@@ -86,6 +86,7 @@
gpios = <&tps659038_gpio 1 GPIO_ACTIVE_HIGH>;
gpio-fan,speed-map = <0 0>,
<13000 1>;
+ #cooling-cells = <2>;
};
extcon_usb1: extcon_usb1 {
@@ -441,6 +442,7 @@
pinctrl-0 = <&tmp102_pins_default>;
interrupt-parent = <&gpio7>;
interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+ #thermal-sensor-cells = <1>;
};
};
@@ -559,3 +561,50 @@
&usb2 {
dr_mode = "peripheral";
};
+
+&cpu_trips {
+ cpu_alert1: cpu_alert1 {
+ temperature = <50000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "active";
+ };
+};
+
+&cpu_cooling_maps {
+ map1 {
+ trip = <&cpu_alert1>;
+ cooling-device = <&gpio_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+};
+
+&thermal_zones {
+ board_thermal: board_thermal {
+ polling-delay-passive = <1250>; /* milliseconds */
+ polling-delay = <1500>; /* milliseconds */
+
+ /* sensor ID */
+ thermal-sensors = <&tmp102 0>;
+
+ board_trips: trips {
+ board_alert0: board_alert {
+ temperature = <40000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "active";
+ };
+
+ board_crit: board_crit {
+ temperature = <105000>; /* millicelsius */
+ hysteresis = <0>; /* millicelsius */
+ type = "critical";
+ };
+ };
+
+ board_cooling_maps: cooling-maps {
+ map0 {
+ trip = <&board_alert0>;
+ cooling-device =
+ <&gpio_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+};
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
