On Mon, Mar 9, 2015 at 12:08 PM, Sebastian Andrzej Siewior <bige...@linutronix.de> wrote: > * Brian Silverman | 2015-03-05 00:16:20 [-0500]: > >>Beforehand, 000 is spending most of its time in interrupts, but bash >>is doing something related to memory management on it in between. >> bash-14721 [000] ......1 6854.629126: rt_spin_lock >> <-free_pcppages_bulk >> bash-14721 [000] ....1.1 6854.629126: mm_page_pcpu_drain: >> page=ffffea000fa1aa40 pfn=4097705 order=0 migratetype=1 >> bash-14721 [000] ......1 6854.629127: get_pfnblock_flags_mask >> <-free_pcppages_bulk >> bash-14721 [000] ......1 6854.629127: __mod_zone_page_state >> <-free_pcppages_bulk >> bash-14721 [000] ....1.1 6854.629127: mm_page_pcpu_drain: >> page=ffffea000f572ac0 pfn=4021419 order=0 migratetype=0 >> bash-14721 [000] ......1 6854.629128: get_pfnblock_flags_mask >> <-free_pcppages_bulk >> bash-14721 [000] ......1 6854.629128: __mod_zone_page_state >> <-free_pcppages_bulk >>... # lots more virtually identical repetitions of those last 3 lines >> bash-14721 [000] ....1.1 6854.629139: mm_page_pcpu_drain: >> page=ffffea000f481a80 pfn=4005994 order=0 migratetype=1 >> bash-14721 [000] ......1 6854.629139: get_pfnblock_flags_mask >> <-free_pcppages_bulk > You free memory and hold the zone->lock > >> bash-14721 [000] d.....1 6854.629139: do_IRQ <-ret_from_intr >> bash-14721 [000] d.....1 6854.629139: irq_enter <-do_IRQ >>... # wakes up the can1 ISR thread on 001 and the can0 one on 000 >>(same physical IRQ line) >> bash-14721 [000] d...3.1 6854.629261: sched_switch: >> prev_comm=bash prev_pid=14721 prev_prio=120 prev_state=R+ ==> >> next_comm=irq/18-can0 next_pid=2015 next_prio=28 > > I would assume that this one raises NET_RX softirq. But at the bottom > you have the irq handler on the other CPU which confuses me…
There wasn't actually any traffic on can0 for this test, so it didn't. The can0 ISR only makes a few reads/writes to the device, never calling netif_rx. The can1 handler (which actually raises a NET_RX softirq) runs on 001 because it's pinned there. > >>... # runs the can0 ISR >> irq/18-can0-2015 [000] d...3.. 6854.629283: sched_switch: >> prev_comm=irq/18-can0 prev_pid=2015 prev_prio=28 prev_state=S ==> >> next_comm=ksoftirqd/0 next_pid=3 next_prio=98 >>... >> ksoftirqd/0-3 [000] ....1.1 6854.629291: softirq_entry: vec=1 >> [action=TIMER] >>... >> ksoftirqd/0-3 [000] ....1.1 6854.629293: softirq_exit: vec=1 >> [action=TIMER] > only the timer since nobody raised NET_RX Correct. I included that as context for what 000 spent its time doing with the lock held, not implying that it's incorrect. > >>... >> ksoftirqd/0-3 [000] ....... 6854.629298: schedule >> <-smpboot_thread_fn ... >> ksoftirqd/0-3 [000] d...3.. 6854.629304: sched_switch: >> prev_comm=ksoftirqd/0 prev_pid=3 prev_prio=98 prev_state=S ==> >> next_comm=bash next_pid=14721 next_prio=28 >>... >> bash-14721 [000] d...1.1 6854.629308: >> smp_trace_reschedule_interrupt <-trace_reschedule_interrupt >># Actually unnecessary schedule IPI from 001? >> bash-14721 [000] d...1.1 6854.629309: irq_enter >> <-smp_trace_reschedule_interrupt >>... >> bash-14721 [000] ....1.1 6854.629316: __tick_nohz_task_switch >> <-__schedule >> bash-14721 [000] ......1 6854.629316: __mod_zone_page_state >> <-free_pcppages_bulk >> bash-14721 [000] ....1.1 6854.629317: mm_page_pcpu_drain: >> page=ffffea000f57a900 pfn=4021924 order=0 migratetype=0 >> bash-14721 [000] ......1 6854.629317: get_pfnblock_flags_mask >> <-free_pcppages_bulk >> bash-14721 [000] ......1 6854.629317: __mod_zone_page_state >> <-free_pcppages_bulk > and it continues cleaning up memory. > >>... # more of this like it was doing before >>I don't see it unlocking the problematic mutex before the trace ends. >> >>The relevant part for 001 starts while it's running the can1 ISR. >> irq/18-can1-7228 [001] ....1.1 6854.629275: netif_rx: dev=can1 >> skbaddr=ffff880412d8fc00 len=16 >> irq/18-can1-7228 [001] ......1 6854.629275: migrate_disable >> <-netif_rx_internal >> irq/18-can1-7228 [001] ......2 6854.629275: enqueue_to_backlog >> <-netif_rx_internal > > enqueue_to_backlog() looks like packet reception so this should be > handled in napi so I assume we run in NET_RX softirq enqueue_to_backlog is the napi function that actually raises the NET_RX softirq. >> irq/18-can1-7228 [001] d.....2 6854.629276: _raw_spin_lock >> <-enqueue_to_backlog >> irq/18-can1-7228 [001] d...1.2 6854.629276: __raise_softirq_irqoff >> <-enqueue_to_backlog >> irq/18-can1-7228 [001] d...1.2 6854.629276: do_raise_softirq_irqoff >> <-__raise_softirq_irqoff >> irq/18-can1-7228 [001] d...2.2 6854.629276: softirq_raise: vec=3 >> [action=NET_RX] This is where the softirq gets raised. >>... # continues handling the can1 interrupt >> irq/18-can1-7228 [001] ......6 6854.629286: rt_spin_lock >> <-get_page_from_freelist >> irq/18-can1-7228 [001] ......6 6854.629287: rt_spin_lock_slowlock >> <-get_page_from_freelist >> irq/18-can1-7228 [001] ......6 6854.629287: _raw_spin_lock >> <-rt_spin_lock_slowlock >> irq/18-can1-7228 [001] ....1.6 6854.629287: __try_to_take_rt_mutex >> <-rt_spin_lock_slowlock >> irq/18-can1-7228 [001] ....1.6 6854.629287: _raw_spin_lock_irq >> <-rt_spin_lock_slowlock >> irq/18-can1-7228 [001] d...2.6 6854.629288: _raw_spin_unlock_irq >> <-rt_spin_lock_slowlock >> irq/18-can1-7228 [001] ....1.6 6854.629288: task_blocks_on_rt_mutex >> <-rt_spin_lock_slowlock > > it might be zone->lock it goes after. It boosts the bash process which > seems to free memory so it would make sense. > >>... # rt_mutex/scheduling stuff >> irq/18-can1-7228 [001] d...4.6 6854.629291: sched_pi_setprio: >> comm=bash pid=14721 oldprio=120 newprio=28 >>... # more scheduler stuff >> irq/18-can1-7228 [001] d...3.6 6854.629299: native_smp_send_reschedule >> <-rt_mutex_setprio >>... # more scheduler stuff >> irq/18-can1-7228 [001] d...2.6 6854.629307: pick_next_task_fair >> <-__schedule >> irq/18-can1-7228 [001] d...2.6 6854.629307: pick_next_task_stop >> <-__schedule >> irq/18-can1-7228 [001] d...2.6 6854.629307: pick_next_task_dl >> <-__schedule >> irq/18-can1-7228 [001] d...2.6 6854.629307: pick_next_task_rt >> <-__schedule >> irq/18-can1-7228 [001] d...2.6 6854.629307: pick_next_task_fair >> <-__schedule >> irq/18-can1-7228 [001] d...2.6 6854.629308: pick_next_task_idle >> <-__schedule >> irq/18-can1-7228 [001] d...3.6 6854.629308: sched_switch: >> prev_comm=irq/18-can1 prev_pid=7228 prev_prio=28 prev_state=D ==> >>next_comm=swapper/1 next_pid=0 next_prio=120 >>... >> <idle>-0 [001] d...1.. 6854.629319: softirq_check_pending_idle >> <-tick_nohz_idle_enter >>My tracing_off() call is in softirq_check_pending_idle, so that's it. > > It looks like your softirq for net_rx is getting a packet and then after > raising NET_RX (again?) it blocks on a lock. In order to get this lock > it boosts and schedules bash. It gets runable but on the other CPU. On > CPU1 there is nothig going is nothing going and the only runable task is > the idle thread. And this is probably where the warning is written > because we go to idle while we should process a softirq instead. That sounds like the issue. Doing the softirq instead of going idle in this situation seems like it means calling thread_do_softirq() from __schedule, but I don't know where the right place is. Can anybody give me some help on where exactly to check for softirqs from? Thanks, Brian -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
