Have you tried it to get it to work without ACPI in the kernel at all, and start from there?
Best regards, Norbert On Saturday 19 February 2005 22:54, you wrote: > Hi everyone, > > I've been banging my head on this one a couple of days with no luck. > > I have a IBM Thinkpad G41 with a pentium4M with Hyperthreading. I can't > get the PCMCIA working at all. I've tried turning off hyperthreading, > I've tried with and without preempt, I've even added pci=noacpi. I've > added Len's ACPI patches, but nothing works. > > Here's lspci -vvv: > > 0000:00:00.0 Host bridge: Intel Corp. 82852/855GM Host Bridge (rev 02) > Subsystem: IBM: Unknown device 0579 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- > DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- > Latency: 0 > Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M] > Capabilities: <available only to root> > > 0000:00:00.1 System peripheral: Intel Corp. 855GM/GME GMCH Memory I/O > Control Registers (rev 02) Subsystem: IBM: Unknown device 057a > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- > DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > > 0000:00:00.3 System peripheral: Intel Corp. 855GM/GME GMCH Configuration > Process Registers (rev 02) Subsystem: IBM: Unknown device 057b > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- > DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > > 0000:00:01.0 PCI bridge: Intel Corp. 855GME GMCH Host-to-AGP Bridge > (Virtual PCI-to-PCI) (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ > Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ > FastB2B- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 96 > Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 > I/O behind bridge: 0000f000-00000fff > Memory behind bridge: c1000000-c1ffffff > Prefetchable memory behind bridge: e0000000-efffffff > BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- > > > [ ... USB controllers snipped out ... ] > > 0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev 81) (prog-if 00 > [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- > VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66MHz- UDF- > FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+ > Latency: 0 > Bus: primary=00, secondary=02, subordinate=08, sec-latency=168 > I/O behind bridge: 00003000-00006fff > Memory behind bridge: c2000000-cfffffff > Prefetchable memory behind bridge: f0000000-f7ffffff > BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- > > 0000:00:1f.0 ISA bridge: Intel Corp. 82801DBM LPC Interface Controller (rev > 01) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- > DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 > > [ ... snipped out IDE Bridge controllers too ... ] > > 0000:00:1f.3 SMBus: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus > Controller (rev 01) Subsystem: IBM: Unknown device 0547 > Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- > DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin B > routed to IRQ 11 > Region 4: I/O ports at 1880 [size=32] > > [ ... snipped audio VGA NVidia and Ethernet controllers ... ] > > 0000:02:01.0 CardBus bridge: Texas Instruments PCI1520 PC card Cardbus > Controller (rev 01) Subsystem: IBM ThinkPad T30/T40 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- > DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168, Cache > Line Size: 0x20 (128 bytes) > Interrupt: pin A routed to IRQ 177 > Region 0: Memory at 3fefb000 (32-bit, non-prefetchable) [size=4K] > Bus: primary=02, secondary=03, subordinate=06, sec-latency=176 > Memory window 0: 40000000-403ff000 (prefetchable) > Memory window 1: 40400000-407ff000 > I/O window 0: 00004000-000040ff > I/O window 1: 00004400-000044ff > BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ > PostWrite+ 16-bit legacy interface ports at 0001 > > 0000:02:01.1 CardBus bridge: Texas Instruments PCI1520 PC card Cardbus > Controller (rev 01) Subsystem: IBM ThinkPad T30/T40 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- > DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168, Cache > Line Size: 0x20 (128 bytes) > Interrupt: pin B routed to IRQ 185 > Region 0: Memory at 3fefc000 (32-bit, non-prefetchable) [size=4K] > Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176 > Memory window 0: 40800000-40bff000 (prefetchable) > Memory window 1: 40c00000-40fff000 > I/O window 0: 00004800-000048ff > I/O window 1: 00004c00-00004cff > BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- > PostWrite+ 16-bit legacy interface ports at 0001 > > > > The above is probably more than anyone needs, but if I should show the > whole listing (USB, Audio and all), just let me know and I can post all > of it too. > > > And here's the dmesg: > > Linux Kernel Card Services > options: [pci] [cardbus] [pm] > ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 20 (level, low) -> IRQ 177 > Yenta: CardBus bridge found at 0000:02:01.0 [1014:0512] > Yenta: Using INTVAL to route CSC interrupts to PCI > Yenta: Routing CardBus interrupts to PCI > Yenta TI: socket 0000:02:01.0, mfunc 0x01001c22, devctl 0x64 > Yenta TI: socket 0000:02:01.0 probing PCI interrupt failed, trying to fix > Yenta TI: socket 0000:02:01.0 no PCI interrupts. Fish. Please report. > Yenta: ISA IRQ mask 0x0000, PCI irq 0 > Socket status: ffffffff > ACPI: PCI interrupt 0000:02:01.1[B] -> GSI 21 (level, low) -> IRQ 185 > Yenta: CardBus bridge found at 0000:02:01.1 [1014:0512] > Yenta: Using CSCINT to route CSC interrupts to PCI > Yenta: Routing CardBus interrupts to PCI > Yenta TI: socket 0000:02:01.1, mfunc 0x01001c22, devctl 0x64 > Yenta TI: socket 0000:02:01.1 probing PCI interrupt failed, trying to fix > Yenta TI: socket 0000:02:01.1 no PCI interrupts. Fish. Please report. > Yenta: ISA IRQ mask 0x0000, PCI irq 0 > Socket status: 4410080c > > (the above is from kernel.org 2.6.10 with Len's ACPI patches). > > I've tried this with Debian stock kernels: 2.4.27-1-386, 2.6.8-2-686, > 2.6.9-1-686, 2.6.10-1-686-smp > > I've also tried kernel.org kernels with 2.6.9, 2.6.10 and > 2.6.11-rc3-mm2. As I've mentioned, I've added Len's ACPI patches to > 2.6.10 and still nothing works. I've tried disable_clkrun but still > nothing. I've found a couple of other patches on the net and nothing > works. > > I've tried debugging this but PCMCIA is not my strong spot, so all I can > tell you is that the interrupt never comes in when Yenta probes it. > > Does anyone else out there have a IBM Thinkpad G41 and have this > working? Or, do you have it and it is not working. I get no power to > the PCMCIA card slots, so they are basically useless now. > > Any ideas would be appreciated. > > Thanks, > > -- Steve > > > - > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in > the body of a message to [EMAIL PROTECTED] > More majordomo info at http://vger.kernel.org/majordomo-info.html > Please read the FAQ at http://www.tux.org/lkml/ -- <a href="http://www.edusupport.nl";>EduSupport: Linux Desktop for schools and small to medium business in The Netherlands and Belgium</a> - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
