Hi Beleswar & Mathieu,
Please find my comments below.
On 7/29/25 10:34 AM, Mathieu Poirier wrote:
Hi Beleswar,
On Thu, Jul 24, 2025 at 07:01:44PM +0530, Beleswar Padhi wrote:
When attaching to a remote processor, it is implied that the rproc was
booted by an external entity. Thus, it's carveout and devmem resources
would already have been processed by the external entity during boot.
Re-allocating the carveouts in Linux (without proper flags) would zero
out the memory regions used by the firmware and can lead to undefined
behaviour. And there is no need to re-map the memory regions for devmem
resources as well.
Therefore, do not process the carveout and devmem resources in attach
mode by not appending them to the rproc->carveouts and rproc->mappings
lists respectively.
I think what you are proposing is logical. Arnaud, Daniel, Iuliana and Tanmay -
please test this on your platforms. I will also need another TB from someone at
TI.
Regards,
Mathieu
Signed-off-by: Beleswar Padhi <b-pa...@ti.com>
---
Testing:
1. Tested IPC with remoteprocs in attach mode in TI platforms.
[However, TI K3 platforms do not use resource table for carveouts,
all the memory regions are reserved statically in Device Tree.]
drivers/remoteproc/remoteproc_core.c | 30 ++++++++++++++++++++++++++++
1 file changed, 30 insertions(+)
diff --git a/drivers/remoteproc/remoteproc_core.c
b/drivers/remoteproc/remoteproc_core.c
index 825672100528..ef709a5fa73c 100644
--- a/drivers/remoteproc/remoteproc_core.c
+++ b/drivers/remoteproc/remoteproc_core.c
@@ -640,6 +640,20 @@ static int rproc_handle_devmem(struct rproc *rproc, void
*ptr,
return -EINVAL;
}
+ /*
+ * When attaching to a remote processor, it is implied that the rproc
+ * was booted by an external entity. Thus, it's devmem resources would
+ * already have been mapped by the external entity during boot. There is
+ * no need to re-map the memory regions here.
+ *
+ * Skip adding the devmem rsc to the mapping list and return without
+ * complaining.
+ */
+ if (rproc->state == RPROC_DETACHED) {
+ dev_info(dev, "skipping devmem rsc in attach mode\n");
+ return 0;
+ }
+
On AMD-Xilinx platforms we don't use RSC_DEVMEM resources so this isn't
affected. And I haven't deep dived into how this works. I would let
Mathieu take decision here.
mapping = kzalloc(sizeof(*mapping), GFP_KERNEL);
if (!mapping)
return -ENOMEM;
@@ -839,6 +853,22 @@ static int rproc_handle_carveout(struct rproc *rproc,
return -EINVAL;
}
+ /*
+ * When attaching to a remote processor, it is implied that the rproc
+ * was booted by an external entity. Thus, it's carveout resources would
+ * already have been allocated by the external entity during boot.
+ * Re-allocating the carveouts here (without proper flags) would zero
+ * out the memory regions used by the firmware and can lead to undefined
+ * behaviour.
+ *
+ * Skip adding the carveouts to the alloc list and return without
+ * complaining.
+ */
+ if (rproc->state == RPROC_DETACHED) {
+ dev_info(dev, "skipping carveout allocation in attach mode\n");
+ return 0;
+ }
+
RSC_CARVEOUT type of resources are used on AMD-Xilinx platform firmwares
and this path I can test. I will let know results once I do that,
But before that I have few comments:
1) This check should be moved right before `rproc_mem_entry_init`. That
means if carveout is found then we should allow flags allocation from
firmware. This can happen if platform driver has already allocated the
carveout and during next attach, we are just updating flags and offset.
2) In this patch following assumption is made:
```
* When attaching to a remote processor, it is implied that the
rproc
* was booted by an external entity. Thus, it's carveout
resources would
* already have been allocated by the external entity during boot.
```
I think this is really platform/firmware dependent. This was not
complained by any other users yet. That could mean they are relying on
Linux to initialize these carveouts and remoteproc firmware may not
initialize it.
To avoid breaking any back compatibility or other's use case (if there
is one),
can we add new feature in rproc->features like:
RPROC_SKIP_ALLOC_CARVEOUT_ON_ATTACH and platform drivers can set that
feature in during probe.
Then we can check that feature here along with DETACHED state and make
decision based on it.
https://github.com/torvalds/linux/blob/89748acdf226fd1a8775ff6fa2703f8412b286c8/include/linux/remoteproc.h#L501
Thanks,
Tanmay
dev_dbg(dev, "carveout rsc: name: %s, da 0x%x, pa 0x%x, len 0x%x, flags
0x%x\n",
rsc->name, rsc->da, rsc->pa, rsc->len, rsc->flags);
--
2.34.1
