From: Arnd Bergmann <a...@arndb.de>
The ST-Ericsson U300 platform is getting removed, so this driver is no
longer needed.
Cc: Linus Walleij <linus.wall...@linaro.org>
Signed-off-by: Arnd Bergmann <a...@arndb.de>
---
drivers/mfd/Kconfig | 26 +-
drivers/mfd/Makefile | 2 -
drivers/mfd/ab3100-core.c | 929 -------------------------------------
drivers/mfd/ab3100-otp.c | 240 ----------
include/linux/mfd/ab3100.h | 128 -----
5 files changed, 1 insertion(+), 1324 deletions(-)
delete mode 100644 drivers/mfd/ab3100-core.c
delete mode 100644 drivers/mfd/ab3100-otp.c
delete mode 100644 include/linux/mfd/ab3100.h
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index bdfce7b15621..2a83b164182a 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -1233,7 +1233,7 @@ config MFD_SC27XX_PMIC
config ABX500_CORE
bool "ST-Ericsson ABX500 Mixed Signal Circuit register functions"
- default y if ARCH_U300 || ARCH_U8500 || COMPILE_TEST
+ default y if ARCH_U8500 || COMPILE_TEST
help
Say yes here if you have the ABX500 Mixed Signal IC family
chips. This core driver expose register access functions.
@@ -1241,30 +1241,6 @@ config ABX500_CORE
remain unchanged when IC changes. Binding of the functions to
actual register access is done by the IC core driver.
-config AB3100_CORE
- bool "ST-Ericsson AB3100 Mixed Signal Circuit core functions"
- depends on I2C=y && ABX500_CORE
- select MFD_CORE
- default y if ARCH_U300
- help
- Select this to enable the AB3100 Mixed Signal IC core
- functionality. This connects to a AB3100 on the I2C bus
- and expose a number of symbols needed for dependent devices
- to read and write registers and subscribe to events from
- this multi-functional IC. This is needed to use other features
- of the AB3100 such as battery-backed RTC, charging control,
- LEDs, vibrator, system power and temperature, power management
- and ALSA sound.
-
-config AB3100_OTP
- tristate "ST-Ericsson AB3100 OTP functions"
- depends on AB3100_CORE
- default y if AB3100_CORE
- help
- Select this to enable the AB3100 Mixed Signal IC OTP (one-time
- programmable memory) support. This exposes a sysfs file to read
- out OTP values.
-
config AB8500_CORE
bool "ST-Ericsson AB8500 Mixed Signal Power Management chip"
depends on ABX500_CORE && MFD_DB8500_PRCMU
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 14fdb188af02..b62a71851c06 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -178,8 +178,6 @@ obj-$(CONFIG_MFD_PCF50633) += pcf50633.o
obj-$(CONFIG_PCF50633_ADC) += pcf50633-adc.o
obj-$(CONFIG_PCF50633_GPIO) += pcf50633-gpio.o
obj-$(CONFIG_ABX500_CORE) += abx500-core.o
-obj-$(CONFIG_AB3100_CORE) += ab3100-core.o
-obj-$(CONFIG_AB3100_OTP) += ab3100-otp.o
obj-$(CONFIG_AB8500_DEBUG) += ab8500-debugfs.o
obj-$(CONFIG_MFD_DB8500_PRCMU) += db8500-prcmu.o
# ab8500-core need to come after db8500-prcmu (which provides the channel)
diff --git a/drivers/mfd/ab3100-core.c b/drivers/mfd/ab3100-core.c
deleted file mode 100644
index ee71ae04b5e6..000000000000
--- a/drivers/mfd/ab3100-core.c
+++ /dev/null
@@ -1,929 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2007-2010 ST-Ericsson
- * Low-level core for exclusive access to the AB3100 IC on the I2C bus
- * and some basic chip-configuration.
- * Author: Linus Walleij <linus.wall...@stericsson.com>
- */
-
-#include <linux/i2c.h>
-#include <linux/mutex.h>
-#include <linux/list.h>
-#include <linux/notifier.h>
-#include <linux/slab.h>
-#include <linux/err.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/device.h>
-#include <linux/interrupt.h>
-#include <linux/random.h>
-#include <linux/debugfs.h>
-#include <linux/seq_file.h>
-#include <linux/uaccess.h>
-#include <linux/mfd/core.h>
-#include <linux/mfd/ab3100.h>
-#include <linux/mfd/abx500.h>
-
-/* These are the only registers inside AB3100 used in this main file */
-
-/* Interrupt event registers */
-#define AB3100_EVENTA1 0x21
-#define AB3100_EVENTA2 0x22
-#define AB3100_EVENTA3 0x23
-
-/* AB3100 DAC converter registers */
-#define AB3100_DIS 0x00
-#define AB3100_D0C 0x01
-#define AB3100_D1C 0x02
-#define AB3100_D2C 0x03
-#define AB3100_D3C 0x04
-
-/* Chip ID register */
-#define AB3100_CID 0x20
-
-/* AB3100 interrupt registers */
-#define AB3100_IMRA1 0x24
-#define AB3100_IMRA2 0x25
-#define AB3100_IMRA3 0x26
-#define AB3100_IMRB1 0x2B
-#define AB3100_IMRB2 0x2C
-#define AB3100_IMRB3 0x2D
-
-/* System Power Monitoring and control registers */
-#define AB3100_MCA 0x2E
-#define AB3100_MCB 0x2F
-
-/* SIM power up */
-#define AB3100_SUP 0x50
-
-/*
- * I2C communication
- *
- * The AB3100 is usually assigned address 0x48 (7-bit)
- * The chip is defined in the platform i2c_board_data section.
- */
-static int ab3100_get_chip_id(struct device *dev)
-{
- struct ab3100 *ab3100 = dev_get_drvdata(dev->parent);
-
- return (int)ab3100->chip_id;
-}
-
-static int ab3100_set_register_interruptible(struct ab3100 *ab3100,
- u8 reg, u8 regval)
-{
- u8 regandval[2] = {reg, regval};
- int err;
-
- err = mutex_lock_interruptible(&ab3100->access_mutex);
- if (err)
- return err;
-
- /*
- * A two-byte write message with the first byte containing the register
- * number and the second byte containing the value to be written
- * effectively sets a register in the AB3100.
- */
- err = i2c_master_send(ab3100->i2c_client, regandval, 2);
- if (err < 0) {
- dev_err(ab3100->dev,
- "write error (write register): %d\n",
- err);
- } else if (err != 2) {
- dev_err(ab3100->dev,
- "write error (write register)\n"
- " %d bytes transferred (expected 2)\n",
- err);
- err = -EIO;
- } else {
- /* All is well */
- err = 0;
- }
- mutex_unlock(&ab3100->access_mutex);
- return err;
-}
-
-static int set_register_interruptible(struct device *dev,
- u8 bank, u8 reg, u8 value)
-{
- struct ab3100 *ab3100 = dev_get_drvdata(dev->parent);
-
- return ab3100_set_register_interruptible(ab3100, reg, value);
-}
-
-/*
- * The test registers exist at an I2C bus address up one
- * from the ordinary base. They are not supposed to be used
- * in production code, but sometimes you have to do that
- * anyway. It's currently only used from this file so declare
- * it static and do not export.
- */
-static int ab3100_set_test_register_interruptible(struct ab3100 *ab3100,
- u8 reg, u8 regval)
-{
- u8 regandval[2] = {reg, regval};
- int err;
-
- err = mutex_lock_interruptible(&ab3100->access_mutex);
- if (err)
- return err;
-
- err = i2c_master_send(ab3100->testreg_client, regandval, 2);
- if (err < 0) {
- dev_err(ab3100->dev,
- "write error (write test register): %d\n",
- err);
- } else if (err != 2) {
- dev_err(ab3100->dev,
- "write error (write test register)\n"
- " %d bytes transferred (expected 2)\n",
- err);
- err = -EIO;
- } else {
- /* All is well */
- err = 0;
- }
- mutex_unlock(&ab3100->access_mutex);
-
- return err;
-}
-
-static int ab3100_get_register_interruptible(struct ab3100 *ab3100,
- u8 reg, u8 *regval)
-{
- int err;
-
- err = mutex_lock_interruptible(&ab3100->access_mutex);
- if (err)
- return err;
-
- /*
- * AB3100 require an I2C "stop" command between each message, else
- * it will not work. The only way of achieveing this with the
- * message transport layer is to send the read and write messages
- * separately.
- */
- err = i2c_master_send(ab3100->i2c_client, ®, 1);
- if (err < 0) {
- dev_err(ab3100->dev,
- "write error (send register address): %d\n",
- err);
- goto get_reg_out_unlock;
- } else if (err != 1) {
- dev_err(ab3100->dev,
- "write error (send register address)\n"
- " %d bytes transferred (expected 1)\n",
- err);
- err = -EIO;
- goto get_reg_out_unlock;
- } else {
- /* All is well */
- err = 0;
- }
-
- err = i2c_master_recv(ab3100->i2c_client, regval, 1);
- if (err < 0) {
- dev_err(ab3100->dev,
- "write error (read register): %d\n",
- err);
- goto get_reg_out_unlock;
- } else if (err != 1) {
- dev_err(ab3100->dev,
- "write error (read register)\n"
- " %d bytes transferred (expected 1)\n",
- err);
- err = -EIO;
- goto get_reg_out_unlock;
- } else {
- /* All is well */
- err = 0;
- }
-
- get_reg_out_unlock:
- mutex_unlock(&ab3100->access_mutex);
- return err;
-}
-
-static int get_register_interruptible(struct device *dev, u8 bank, u8 reg,
- u8 *value)
-{
- struct ab3100 *ab3100 = dev_get_drvdata(dev->parent);
-
- return ab3100_get_register_interruptible(ab3100, reg, value);
-}
-
-static int ab3100_get_register_page_interruptible(struct ab3100 *ab3100,
- u8 first_reg, u8 *regvals, u8 numregs)
-{
- int err;
-
- if (ab3100->chip_id == 0xa0 ||
- ab3100->chip_id == 0xa1)
- /* These don't support paged reads */
- return -EIO;
-
- err = mutex_lock_interruptible(&ab3100->access_mutex);
- if (err)
- return err;
-
- /*
- * Paged read also require an I2C "stop" command.
- */
- err = i2c_master_send(ab3100->i2c_client, &first_reg, 1);
- if (err < 0) {
- dev_err(ab3100->dev,
- "write error (send first register address): %d\n",
- err);
- goto get_reg_page_out_unlock;
- } else if (err != 1) {
- dev_err(ab3100->dev,
- "write error (send first register address)\n"
- " %d bytes transferred (expected 1)\n",
- err);
- err = -EIO;
- goto get_reg_page_out_unlock;
- }
-
- err = i2c_master_recv(ab3100->i2c_client, regvals, numregs);
- if (err < 0) {
- dev_err(ab3100->dev,
- "write error (read register page): %d\n",
- err);
- goto get_reg_page_out_unlock;
- } else if (err != numregs) {
- dev_err(ab3100->dev,
- "write error (read register page)\n"
- " %d bytes transferred (expected %d)\n",
- err, numregs);
- err = -EIO;
- goto get_reg_page_out_unlock;
- }
-
- /* All is well */
- err = 0;
-
- get_reg_page_out_unlock:
- mutex_unlock(&ab3100->access_mutex);
- return err;
-}
-
-static int get_register_page_interruptible(struct device *dev, u8 bank,
- u8 first_reg, u8 *regvals, u8 numregs)
-{
- struct ab3100 *ab3100 = dev_get_drvdata(dev->parent);
-
- return ab3100_get_register_page_interruptible(ab3100,
- first_reg, regvals, numregs);
-}
-
-static int ab3100_mask_and_set_register_interruptible(struct ab3100 *ab3100,
- u8 reg, u8 andmask, u8 ormask)
-{
- u8 regandval[2] = {reg, 0};
- int err;
-
- err = mutex_lock_interruptible(&ab3100->access_mutex);
- if (err)
- return err;
-
- /* First read out the target register */
- err = i2c_master_send(ab3100->i2c_client, ®, 1);
- if (err < 0) {
- dev_err(ab3100->dev,
- "write error (maskset send address): %d\n",
- err);
- goto get_maskset_unlock;
- } else if (err != 1) {
- dev_err(ab3100->dev,
- "write error (maskset send address)\n"
- " %d bytes transferred (expected 1)\n",
- err);
- err = -EIO;
- goto get_maskset_unlock;
- }
-
- err = i2c_master_recv(ab3100->i2c_client, ®andval[1], 1);
- if (err < 0) {
- dev_err(ab3100->dev,
- "write error (maskset read register): %d\n",
- err);
- goto get_maskset_unlock;
- } else if (err != 1) {
- dev_err(ab3100->dev,
- "write error (maskset read register)\n"
- " %d bytes transferred (expected 1)\n",
- err);
- err = -EIO;
- goto get_maskset_unlock;
- }
-
- /* Modify the register */
- regandval[1] &= andmask;
- regandval[1] |= ormask;
-
- /* Write the register */
- err = i2c_master_send(ab3100->i2c_client, regandval, 2);
- if (err < 0) {
- dev_err(ab3100->dev,
- "write error (write register): %d\n",
- err);
- goto get_maskset_unlock;
- } else if (err != 2) {
- dev_err(ab3100->dev,
- "write error (write register)\n"
- " %d bytes transferred (expected 2)\n",
- err);
- err = -EIO;
- goto get_maskset_unlock;
- }
-
- /* All is well */
- err = 0;
-
- get_maskset_unlock:
- mutex_unlock(&ab3100->access_mutex);
- return err;
-}
-
-static int mask_and_set_register_interruptible(struct device *dev, u8 bank,
- u8 reg, u8 bitmask, u8 bitvalues)
-{
- struct ab3100 *ab3100 = dev_get_drvdata(dev->parent);
-
- return ab3100_mask_and_set_register_interruptible(ab3100,
- reg, bitmask, (bitmask & bitvalues));
-}
-
-/*
- * Register a simple callback for handling any AB3100 events.
- */
-int ab3100_event_register(struct ab3100 *ab3100,
- struct notifier_block *nb)
-{
- return blocking_notifier_chain_register(&ab3100->event_subscribers,
- nb);
-}
-EXPORT_SYMBOL(ab3100_event_register);
-
-/*
- * Remove a previously registered callback.
- */
-int ab3100_event_unregister(struct ab3100 *ab3100,
- struct notifier_block *nb)
-{
- return blocking_notifier_chain_unregister(&ab3100->event_subscribers,
- nb);
-}
-EXPORT_SYMBOL(ab3100_event_unregister);
-
-
-static int ab3100_event_registers_startup_state_get(struct device *dev,
- u8 *event)
-{
- struct ab3100 *ab3100 = dev_get_drvdata(dev->parent);
-
- if (!ab3100->startup_events_read)
- return -EAGAIN; /* Try again later */
- memcpy(event, ab3100->startup_events, 3);
-
- return 0;
-}
-
-static struct abx500_ops ab3100_ops = {
- .get_chip_id = ab3100_get_chip_id,
- .set_register = set_register_interruptible,
- .get_register = get_register_interruptible,
- .get_register_page = get_register_page_interruptible,
- .set_register_page = NULL,
- .mask_and_set_register = mask_and_set_register_interruptible,
- .event_registers_startup_state_get =
- ab3100_event_registers_startup_state_get,
- .startup_irq_enabled = NULL,
-};
-
-/*
- * This is a threaded interrupt handler so we can make some
- * I2C calls etc.
- */
-static irqreturn_t ab3100_irq_handler(int irq, void *data)
-{
- struct ab3100 *ab3100 = data;
- u8 event_regs[3];
- u32 fatevent;
- int err;
-
- err = ab3100_get_register_page_interruptible(ab3100, AB3100_EVENTA1,
- event_regs, 3);
- if (err)
- goto err_event;
-
- fatevent = (event_regs[0] << 16) |
- (event_regs[1] << 8) |
- event_regs[2];
-
- if (!ab3100->startup_events_read) {
- ab3100->startup_events[0] = event_regs[0];
- ab3100->startup_events[1] = event_regs[1];
- ab3100->startup_events[2] = event_regs[2];
- ab3100->startup_events_read = true;
- }
- /*
- * The notified parties will have to mask out the events
- * they're interested in and react to them. They will be
- * notified on all events, then they use the fatevent value
- * to determine if they're interested.
- */
- blocking_notifier_call_chain(&ab3100->event_subscribers,
- fatevent, NULL);
-
- dev_dbg(ab3100->dev,
- "IRQ Event: 0x%08x\n", fatevent);
-
- return IRQ_HANDLED;
-
- err_event:
- dev_dbg(ab3100->dev,
- "error reading event status\n");
- return IRQ_HANDLED;
-}
-
-#ifdef CONFIG_DEBUG_FS
-/*
- * Some debugfs entries only exposed if we're using debug
- */
-static int ab3100_registers_print(struct seq_file *s, void *p)
-{
- struct ab3100 *ab3100 = s->private;
- u8 value;
- u8 reg;
-
- seq_puts(s, "AB3100 registers:\n");
-
- for (reg = 0; reg < 0xff; reg++) {
- ab3100_get_register_interruptible(ab3100, reg, &value);
- seq_printf(s, "[0x%x]: 0x%x\n", reg, value);
- }
- return 0;
-}
-
-static int ab3100_registers_open(struct inode *inode, struct file *file)
-{
- return single_open(file, ab3100_registers_print, inode->i_private);
-}
-
-static const struct file_operations ab3100_registers_fops = {
- .open = ab3100_registers_open,
- .read = seq_read,
- .llseek = seq_lseek,
- .release = single_release,
- .owner = THIS_MODULE,
-};
-
-struct ab3100_get_set_reg_priv {
- struct ab3100 *ab3100;
- bool mode;
-};
-
-static ssize_t ab3100_get_set_reg(struct file *file,
- const char __user *user_buf,
- size_t count, loff_t *ppos)
-{
- struct ab3100_get_set_reg_priv *priv = file->private_data;
- struct ab3100 *ab3100 = priv->ab3100;
- char buf[32];
- ssize_t buf_size;
- int regp;
- u8 user_reg;
- int err;
- int i = 0;
-
- /* Get userspace string and assure termination */
- buf_size = min((ssize_t)count, (ssize_t)(sizeof(buf)-1));
- if (copy_from_user(buf, user_buf, buf_size))
- return -EFAULT;
- buf[buf_size] = 0;
-
- /*
- * The idea is here to parse a string which is either
- * "0xnn" for reading a register, or "0xaa 0xbb" for
- * writing 0xbb to the register 0xaa. First move past
- * whitespace and then begin to parse the register.
- */
- while ((i < buf_size) && (buf[i] == ' '))
- i++;
- regp = i;
-
- /*
- * Advance pointer to end of string then terminate
- * the register string. This is needed to satisfy
- * the kstrtou8() function.
- */
- while ((i < buf_size) && (buf[i] != ' '))
- i++;
- buf[i] = '\0';
-
- err = kstrtou8(&buf[regp], 16, &user_reg);
- if (err)
- return err;
-
- /* Either we read or we write a register here */
- if (!priv->mode) {
- /* Reading */
- u8 regvalue;
-
- ab3100_get_register_interruptible(ab3100, user_reg, ®value);
-
- dev_info(ab3100->dev,
- "debug read AB3100 reg[0x%02x]: 0x%02x\n",
- user_reg, regvalue);
- } else {
- int valp;
- u8 user_value;
- u8 regvalue;
-
- /*
- * Writing, we need some value to write to
- * the register so keep parsing the string
- * from userspace.
- */
- i++;
- while ((i < buf_size) && (buf[i] == ' '))
- i++;
- valp = i;
- while ((i < buf_size) && (buf[i] != ' '))
- i++;
- buf[i] = '\0';
-
- err = kstrtou8(&buf[valp], 16, &user_value);
- if (err)
- return err;
-
- ab3100_set_register_interruptible(ab3100, user_reg, user_value);
- ab3100_get_register_interruptible(ab3100, user_reg, ®value);
-
- dev_info(ab3100->dev,
- "debug write reg[0x%02x]\n"
- " with 0x%02x, after readback: 0x%02x\n",
- user_reg, user_value, regvalue);
- }
- return buf_size;
-}
-
-static const struct file_operations ab3100_get_set_reg_fops = {
- .open = simple_open,
- .write = ab3100_get_set_reg,
- .llseek = noop_llseek,
-};
-
-static struct ab3100_get_set_reg_priv ab3100_get_priv;
-static struct ab3100_get_set_reg_priv ab3100_set_priv;
-
-static void ab3100_setup_debugfs(struct ab3100 *ab3100)
-{
- struct dentry *ab3100_dir;
-
- ab3100_dir = debugfs_create_dir("ab3100", NULL);
-
- debugfs_create_file("registers", S_IRUGO, ab3100_dir, ab3100,
- &ab3100_registers_fops);
-
- ab3100_get_priv.ab3100 = ab3100;
- ab3100_get_priv.mode = false;
- debugfs_create_file("get_reg", S_IWUSR, ab3100_dir, &ab3100_get_priv,
- &ab3100_get_set_reg_fops);
-
- ab3100_set_priv.ab3100 = ab3100;
- ab3100_set_priv.mode = true;
- debugfs_create_file("set_reg", S_IWUSR, ab3100_dir, &ab3100_set_priv,
- &ab3100_get_set_reg_fops);
-}
-#else
-static inline void ab3100_setup_debugfs(struct ab3100 *ab3100)
-{
-}
-#endif
-
-/*
- * Basic set-up, datastructure creation/destruction and I2C interface.
- * This sets up a default config in the AB3100 chip so that it
- * will work as expected.
- */
-
-struct ab3100_init_setting {
- u8 abreg;
- u8 setting;
-};
-
-static const struct ab3100_init_setting ab3100_init_settings[] = {
- {
- .abreg = AB3100_MCA,
- .setting = 0x01
- }, {
- .abreg = AB3100_MCB,
- .setting = 0x30
- }, {
- .abreg = AB3100_IMRA1,
- .setting = 0x00
- }, {
- .abreg = AB3100_IMRA2,
- .setting = 0xFF
- }, {
- .abreg = AB3100_IMRA3,
- .setting = 0x01
- }, {
- .abreg = AB3100_IMRB1,
- .setting = 0xBF
- }, {
- .abreg = AB3100_IMRB2,
- .setting = 0xFF
- }, {
- .abreg = AB3100_IMRB3,
- .setting = 0xFF
- }, {
- .abreg = AB3100_SUP,
- .setting = 0x00
- }, {
- .abreg = AB3100_DIS,
- .setting = 0xF0
- }, {
- .abreg = AB3100_D0C,
- .setting = 0x00
- }, {
- .abreg = AB3100_D1C,
- .setting = 0x00
- }, {
- .abreg = AB3100_D2C,
- .setting = 0x00
- }, {
- .abreg = AB3100_D3C,
- .setting = 0x00
- },
-};
-
-static int ab3100_setup(struct ab3100 *ab3100)
-{
- int err = 0;
- int i;
-
- for (i = 0; i < ARRAY_SIZE(ab3100_init_settings); i++) {
- err = ab3100_set_register_interruptible(ab3100,
- ab3100_init_settings[i].abreg,
- ab3100_init_settings[i].setting);
- if (err)
- goto exit_no_setup;
- }
-
- /*
- * Special trick to make the AB3100 use the 32kHz clock (RTC)
- * bit 3 in test register 0x02 is a special, undocumented test
- * register bit that only exist in AB3100 P1E
- */
- if (ab3100->chip_id == 0xc4) {
- dev_warn(ab3100->dev,
- "AB3100 P1E variant detected forcing chip to 32KHz\n");
- err = ab3100_set_test_register_interruptible(ab3100,
- 0x02, 0x08);
- }
-
- exit_no_setup:
- return err;
-}
-
-/* The subdevices of the AB3100 */
-static struct mfd_cell ab3100_devs[] = {
- {
- .name = "ab3100-dac",
- .id = -1,
- },
- {
- .name = "ab3100-leds",
- .id = -1,
- },
- {
- .name = "ab3100-power",
- .id = -1,
- },
- {
- .name = "ab3100-regulators",
- .of_compatible = "stericsson,ab3100-regulators",
- .id = -1,
- },
- {
- .name = "ab3100-sim",
- .id = -1,
- },
- {
- .name = "ab3100-uart",
- .id = -1,
- },
- {
- .name = "ab3100-rtc",
- .id = -1,
- },
- {
- .name = "ab3100-charger",
- .id = -1,
- },
- {
- .name = "ab3100-boost",
- .id = -1,
- },
- {
- .name = "ab3100-adc",
- .id = -1,
- },
- {
- .name = "ab3100-fuelgauge",
- .id = -1,
- },
- {
- .name = "ab3100-vibrator",
- .id = -1,
- },
- {
- .name = "ab3100-otp",
- .id = -1,
- },
- {
- .name = "ab3100-codec",
- .id = -1,
- },
-};
-
-struct ab_family_id {
- u8 id;
- char *name;
-};
-
-static const struct ab_family_id ids[] = {
- /* AB3100 */
- {
- .id = 0xc0,
- .name = "P1A"
- }, {
- .id = 0xc1,
- .name = "P1B"
- }, {
- .id = 0xc2,
- .name = "P1C"
- }, {
- .id = 0xc3,
- .name = "P1D"
- }, {
- .id = 0xc4,
- .name = "P1E"
- }, {
- .id = 0xc5,
- .name = "P1F/R1A"
- }, {
- .id = 0xc6,
- .name = "P1G/R1A"
- }, {
- .id = 0xc7,
- .name = "P2A/R2A"
- }, {
- .id = 0xc8,
- .name = "P2B/R2B"
- },
- /* AB3000 variants, not supported */
- {
- .id = 0xa0
- }, {
- .id = 0xa1
- }, {
- .id = 0xa2
- }, {
- .id = 0xa3
- }, {
- .id = 0xa4
- }, {
- .id = 0xa5
- }, {
- .id = 0xa6
- }, {
- .id = 0xa7
- },
- /* Terminator */
- {
- .id = 0x00,
- },
-};
-
-static int ab3100_probe(struct i2c_client *client,
- const struct i2c_device_id *id)
-{
- struct ab3100 *ab3100;
- struct ab3100_platform_data *ab3100_plf_data =
- dev_get_platdata(&client->dev);
- int err;
- int i;
-
- ab3100 = devm_kzalloc(&client->dev, sizeof(struct ab3100), GFP_KERNEL);
- if (!ab3100)
- return -ENOMEM;
-
- /* Initialize data structure */
- mutex_init(&ab3100->access_mutex);
- BLOCKING_INIT_NOTIFIER_HEAD(&ab3100->event_subscribers);
-
- ab3100->i2c_client = client;
- ab3100->dev = &ab3100->i2c_client->dev;
-
- i2c_set_clientdata(client, ab3100);
-
- /* Read chip ID register */
- err = ab3100_get_register_interruptible(ab3100, AB3100_CID,
- &ab3100->chip_id);
- if (err) {
- dev_err(&client->dev,
- "failed to communicate with AB3100 chip\n");
- goto exit_no_detect;
- }
-
- for (i = 0; ids[i].id != 0x0; i++) {
- if (ids[i].id == ab3100->chip_id) {
- if (ids[i].name)
- break;
-
- dev_err(&client->dev, "AB3000 is not supported\n");
- goto exit_no_detect;
- }
- }
-
- snprintf(&ab3100->chip_name[0],
- sizeof(ab3100->chip_name) - 1, "AB3100 %s", ids[i].name);
-
- if (ids[i].id == 0x0) {
- dev_err(&client->dev, "unknown analog baseband chip id: 0x%x\n",
- ab3100->chip_id);
- dev_err(&client->dev,
- "accepting it anyway. Please update the driver.\n");
- goto exit_no_detect;
- }
-
- dev_info(&client->dev, "Detected chip: %s\n",
- &ab3100->chip_name[0]);
-
- /* Attach a second dummy i2c_client to the test register address */
- ab3100->testreg_client = i2c_new_dummy_device(client->adapter,
- client->addr + 1);
- if (IS_ERR(ab3100->testreg_client)) {
- err = PTR_ERR(ab3100->testreg_client);
- goto exit_no_testreg_client;
- }
-
- err = ab3100_setup(ab3100);
- if (err)
- goto exit_no_setup;
-
- err = devm_request_threaded_irq(&client->dev,
- client->irq, NULL, ab3100_irq_handler,
- IRQF_ONESHOT, "ab3100-core", ab3100);
- if (err)
- goto exit_no_irq;
-
- err = abx500_register_ops(&client->dev, &ab3100_ops);
- if (err)
- goto exit_no_ops;
-
- /* Set up and register the platform devices. */
- for (i = 0; i < ARRAY_SIZE(ab3100_devs); i++) {
- ab3100_devs[i].platform_data = ab3100_plf_data;
- ab3100_devs[i].pdata_size = sizeof(struct ab3100_platform_data);
- }
-
- err = mfd_add_devices(&client->dev, 0, ab3100_devs,
- ARRAY_SIZE(ab3100_devs), NULL, 0, NULL);
-
- ab3100_setup_debugfs(ab3100);
-
- return 0;
-
- exit_no_ops:
- exit_no_irq:
- exit_no_setup:
- i2c_unregister_device(ab3100->testreg_client);
- exit_no_testreg_client:
- exit_no_detect:
- return err;
-}
-
-static const struct i2c_device_id ab3100_id[] = {
- { "ab3100", 0 },
- { }
-};
-
-static struct i2c_driver ab3100_driver = {
- .driver = {
- .name = "ab3100",
- .suppress_bind_attrs = true,
- },
- .id_table = ab3100_id,
- .probe = ab3100_probe,
-};
-
-static int __init ab3100_i2c_init(void)
-{
- return i2c_add_driver(&ab3100_driver);
-}
-subsys_initcall(ab3100_i2c_init);
diff --git a/drivers/mfd/ab3100-otp.c b/drivers/mfd/ab3100-otp.c
deleted file mode 100644
index c393102e3a39..000000000000
--- a/drivers/mfd/ab3100-otp.c
+++ /dev/null
@@ -1,240 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * drivers/mfd/ab3100_otp.c
- *
- * Copyright (C) 2007-2009 ST-Ericsson AB
- * Driver to read out OTP from the AB3100 Mixed-signal circuit
- * Author: Linus Walleij <linus.wall...@stericsson.com>
- */
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/slab.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mfd/abx500.h>
-#include <linux/debugfs.h>
-#include <linux/seq_file.h>
-
-/* The OTP registers */
-#define AB3100_OTP0 0xb0
-#define AB3100_OTP1 0xb1
-#define AB3100_OTP2 0xb2
-#define AB3100_OTP3 0xb3
-#define AB3100_OTP4 0xb4
-#define AB3100_OTP5 0xb5
-#define AB3100_OTP6 0xb6
-#define AB3100_OTP7 0xb7
-#define AB3100_OTPP 0xbf
-
-/**
- * struct ab3100_otp
- * @dev: containing device
- * @locked: whether the OTP is locked, after locking, no more bits
- * can be changed but before locking it is still possible
- * to change bits from 1->0.
- * @freq: clocking frequency for the OTP, this frequency is either
- * 32768Hz or 1MHz/30
- * @paf: product activation flag, indicates whether this is a real
- * product (paf true) or a lab board etc (paf false)
- * @imeich: if this is set it is possible to override the
- * IMEI number found in the tac, fac and svn fields with
- * (secured) software
- * @cid: customer ID
- * @tac: type allocation code of the IMEI
- * @fac: final assembly code of the IMEI
- * @svn: software version number of the IMEI
- * @debugfs: a debugfs file used when dumping to file
- */
-struct ab3100_otp {
- struct device *dev;
- bool locked;
- u32 freq;
- bool paf;
- bool imeich;
- u16 cid:14;
- u32 tac:20;
- u8 fac;
- u32 svn:20;
- struct dentry *debugfs;
-};
-
-static int __init ab3100_otp_read(struct ab3100_otp *otp)
-{
- u8 otpval[8];
- u8 otpp;
- int err;
-
- err = abx500_get_register_interruptible(otp->dev, 0,
- AB3100_OTPP, &otpp);
- if (err) {
- dev_err(otp->dev, "unable to read OTPP register\n");
- return err;
- }
-
- err = abx500_get_register_page_interruptible(otp->dev, 0,
- AB3100_OTP0, otpval, 8);
- if (err) {
- dev_err(otp->dev, "unable to read OTP register page\n");
- return err;
- }
-
- /* Cache OTP properties, they never change by nature */
- otp->locked = (otpp & 0x80);
- otp->freq = (otpp & 0x40) ? 32768 : 34100;
- otp->paf = (otpval[1] & 0x80);
- otp->imeich = (otpval[1] & 0x40);
- otp->cid = ((otpval[1] << 8) | otpval[0]) & 0x3fff;
- otp->tac = ((otpval[4] & 0x0f) << 16) | (otpval[3] << 8) | otpval[2];
- otp->fac = ((otpval[5] & 0x0f) << 4) | (otpval[4] >> 4);
- otp->svn = (otpval[7] << 12) | (otpval[6] << 4) | (otpval[5] >> 4);
- return 0;
-}
-
-/*
- * This is a simple debugfs human-readable file that dumps out
- * the contents of the OTP.
- */
-#ifdef CONFIG_DEBUG_FS
-static int ab3100_show_otp(struct seq_file *s, void *v)
-{
- struct ab3100_otp *otp = s->private;
-
- seq_printf(s, "OTP is %s\n", otp->locked ? "LOCKED" : "UNLOCKED");
- seq_printf(s, "OTP clock switch startup is %uHz\n", otp->freq);
- seq_printf(s, "PAF is %s\n", otp->paf ? "SET" : "NOT SET");
- seq_printf(s, "IMEI is %s\n", otp->imeich ?
- "CHANGEABLE" : "NOT CHANGEABLE");
- seq_printf(s, "CID: 0x%04x (decimal: %d)\n", otp->cid, otp->cid);
- seq_printf(s, "IMEI: %u-%u-%u\n", otp->tac, otp->fac, otp->svn);
- return 0;
-}
-
-static int ab3100_otp_open(struct inode *inode, struct file *file)
-{
- return single_open(file, ab3100_show_otp, inode->i_private);
-}
-
-static const struct file_operations ab3100_otp_operations = {
- .open = ab3100_otp_open,
- .read = seq_read,
- .llseek = seq_lseek,
- .release = single_release,
-};
-
-static void __init ab3100_otp_init_debugfs(struct device *dev,
- struct ab3100_otp *otp)
-{
- otp->debugfs = debugfs_create_file("ab3100_otp", S_IFREG | S_IRUGO,
- NULL, otp, &ab3100_otp_operations);
-}
-
-static void __exit ab3100_otp_exit_debugfs(struct ab3100_otp *otp)
-{
- debugfs_remove(otp->debugfs);
-}
-#else
-/* Compile this out if debugfs not selected */
-static inline void __init ab3100_otp_init_debugfs(struct device *dev,
- struct ab3100_otp *otp)
-{
-}
-
-static inline void __exit ab3100_otp_exit_debugfs(struct ab3100_otp *otp)
-{
-}
-#endif
-
-#define SHOW_AB3100_ATTR(name) \
-static ssize_t ab3100_otp_##name##_show(struct device *dev, \
- struct device_attribute *attr, \
- char *buf) \
-{\
- struct ab3100_otp *otp = dev_get_drvdata(dev); \
- return sprintf(buf, "%u\n", otp->name); \
-}
-
-SHOW_AB3100_ATTR(locked)
-SHOW_AB3100_ATTR(freq)
-SHOW_AB3100_ATTR(paf)
-SHOW_AB3100_ATTR(imeich)
-SHOW_AB3100_ATTR(cid)
-SHOW_AB3100_ATTR(fac)
-SHOW_AB3100_ATTR(tac)
-SHOW_AB3100_ATTR(svn)
-
-static struct device_attribute ab3100_otp_attrs[] = {
- __ATTR(locked, S_IRUGO, ab3100_otp_locked_show, NULL),
- __ATTR(freq, S_IRUGO, ab3100_otp_freq_show, NULL),
- __ATTR(paf, S_IRUGO, ab3100_otp_paf_show, NULL),
- __ATTR(imeich, S_IRUGO, ab3100_otp_imeich_show, NULL),
- __ATTR(cid, S_IRUGO, ab3100_otp_cid_show, NULL),
- __ATTR(fac, S_IRUGO, ab3100_otp_fac_show, NULL),
- __ATTR(tac, S_IRUGO, ab3100_otp_tac_show, NULL),
- __ATTR(svn, S_IRUGO, ab3100_otp_svn_show, NULL),
-};
-
-static int __init ab3100_otp_probe(struct platform_device *pdev)
-{
- struct ab3100_otp *otp;
- int err = 0;
- int i;
-
- otp = devm_kzalloc(&pdev->dev, sizeof(struct ab3100_otp), GFP_KERNEL);
- if (!otp)
- return -ENOMEM;
-
- otp->dev = &pdev->dev;
-
- /* Replace platform data coming in with a local struct */
- platform_set_drvdata(pdev, otp);
-
- err = ab3100_otp_read(otp);
- if (err)
- return err;
-
- dev_info(&pdev->dev, "AB3100 OTP readout registered\n");
-
- /* sysfs entries */
- for (i = 0; i < ARRAY_SIZE(ab3100_otp_attrs); i++) {
- err = device_create_file(&pdev->dev,
- &ab3100_otp_attrs[i]);
- if (err)
- goto err;
- }
-
- /* debugfs entries */
- ab3100_otp_init_debugfs(&pdev->dev, otp);
-
- return 0;
-
-err:
- while (--i >= 0)
- device_remove_file(&pdev->dev, &ab3100_otp_attrs[i]);
- return err;
-}
-
-static int __exit ab3100_otp_remove(struct platform_device *pdev)
-{
- struct ab3100_otp *otp = platform_get_drvdata(pdev);
- int i;
-
- for (i = 0; i < ARRAY_SIZE(ab3100_otp_attrs); i++)
- device_remove_file(&pdev->dev,
- &ab3100_otp_attrs[i]);
- ab3100_otp_exit_debugfs(otp);
- return 0;
-}
-
-static struct platform_driver ab3100_otp_driver = {
- .driver = {
- .name = "ab3100-otp",
- },
- .remove = __exit_p(ab3100_otp_remove),
-};
-
-module_platform_driver_probe(ab3100_otp_driver, ab3100_otp_probe);
-
-MODULE_AUTHOR("Linus Walleij <linus.wall...@stericsson.com>");
-MODULE_DESCRIPTION("AB3100 OTP Readout Driver");
-MODULE_LICENSE("GPL");
diff --git a/include/linux/mfd/ab3100.h b/include/linux/mfd/ab3100.h
deleted file mode 100644
index a881d8495186..000000000000
--- a/include/linux/mfd/ab3100.h
+++ /dev/null
@@ -1,128 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (C) 2007-2009 ST-Ericsson AB
- * AB3100 core access functions
- * Author: Linus Walleij <linus.wall...@stericsson.com>
- */
-
-#include <linux/regulator/machine.h>
-
-struct device;
-
-#ifndef MFD_AB3100_H
-#define MFD_AB3100_H
-
-
-#define AB3100_P1A 0xc0
-#define AB3100_P1B 0xc1
-#define AB3100_P1C 0xc2
-#define AB3100_P1D 0xc3
-#define AB3100_P1E 0xc4
-#define AB3100_P1F 0xc5
-#define AB3100_P1G 0xc6
-#define AB3100_R2A 0xc7
-#define AB3100_R2B 0xc8
-
-/*
- * AB3100, EVENTA1, A2 and A3 event register flags
- * these are catenated into a single 32-bit flag in the code
- * for event notification broadcasts.
- */
-#define AB3100_EVENTA1_ONSWA (0x01<<16)
-#define AB3100_EVENTA1_ONSWB (0x02<<16)
-#define AB3100_EVENTA1_ONSWC (0x04<<16)
-#define AB3100_EVENTA1_DCIO (0x08<<16)
-#define AB3100_EVENTA1_OVER_TEMP (0x10<<16)
-#define AB3100_EVENTA1_SIM_OFF (0x20<<16)
-#define AB3100_EVENTA1_VBUS (0x40<<16)
-#define AB3100_EVENTA1_VSET_USB (0x80<<16)
-
-#define AB3100_EVENTA2_READY_TX (0x01<<8)
-#define AB3100_EVENTA2_READY_RX (0x02<<8)
-#define AB3100_EVENTA2_OVERRUN_ERROR (0x04<<8)
-#define AB3100_EVENTA2_FRAMING_ERROR (0x08<<8)
-#define AB3100_EVENTA2_CHARG_OVERCURRENT (0x10<<8)
-#define AB3100_EVENTA2_MIDR (0x20<<8)
-#define AB3100_EVENTA2_BATTERY_REM (0x40<<8)
-#define AB3100_EVENTA2_ALARM (0x80<<8)
-
-#define AB3100_EVENTA3_ADC_TRIG5 (0x01)
-#define AB3100_EVENTA3_ADC_TRIG4 (0x02)
-#define AB3100_EVENTA3_ADC_TRIG3 (0x04)
-#define AB3100_EVENTA3_ADC_TRIG2 (0x08)
-#define AB3100_EVENTA3_ADC_TRIGVBAT (0x10)
-#define AB3100_EVENTA3_ADC_TRIGVTX (0x20)
-#define AB3100_EVENTA3_ADC_TRIG1 (0x40)
-#define AB3100_EVENTA3_ADC_TRIG0 (0x80)
-
-/* AB3100, STR register flags */
-#define AB3100_STR_ONSWA (0x01)
-#define AB3100_STR_ONSWB (0x02)
-#define AB3100_STR_ONSWC (0x04)
-#define AB3100_STR_DCIO (0x08)
-#define AB3100_STR_BOOT_MODE (0x10)
-#define AB3100_STR_SIM_OFF (0x20)
-#define AB3100_STR_BATT_REMOVAL (0x40)
-#define AB3100_STR_VBUS (0x80)
-
-/*
- * AB3100 contains 8 regulators, one external regulator controller
- * and a buck converter, further the LDO E and buck converter can
- * have separate settings if they are in sleep mode, this is
- * modeled as a separate regulator.
- */
-#define AB3100_NUM_REGULATORS 10
-
-/**
- * struct ab3100
- * @access_mutex: lock out concurrent accesses to the AB3100 registers
- * @dev: pointer to the containing device
- * @i2c_client: I2C client for this chip
- * @testreg_client: secondary client for test registers
- * @chip_name: name of this chip variant
- * @chip_id: 8 bit chip ID for this chip variant
- * @event_subscribers: event subscribers are listed here
- * @startup_events: a copy of the first reading of the event registers
- * @startup_events_read: whether the first events have been read
- *
- * This struct is PRIVATE and devices using it should NOT
- * access ANY fields. It is used as a token for calling the
- * AB3100 functions.
- */
-struct ab3100 {
- struct mutex access_mutex;
- struct device *dev;
- struct i2c_client *i2c_client;
- struct i2c_client *testreg_client;
- char chip_name[32];
- u8 chip_id;
- struct blocking_notifier_head event_subscribers;
- u8 startup_events[3];
- bool startup_events_read;
-};
-
-/**
- * struct ab3100_platform_data
- * Data supplied to initialize board connections to the AB3100
- * @reg_constraints: regulator constraints for target board
- * the order of these constraints are: LDO A, C, D, E,
- * F, G, H, K, EXT and BUCK.
- * @reg_initvals: initial values for the regulator registers
- * plus two sleep settings for LDO E and the BUCK converter.
- * exactly AB3100_NUM_REGULATORS+2 values must be sent in.
- * Order: LDO A, C, E, E sleep, F, G, H, K, EXT, BUCK,
- * BUCK sleep, LDO D. (LDO D need to be initialized last.)
- * @external_voltage: voltage level of the external regulator.
- */
-struct ab3100_platform_data {
- struct regulator_init_data reg_constraints[AB3100_NUM_REGULATORS];
- u8 reg_initvals[AB3100_NUM_REGULATORS+2];
- int external_voltage;
-};
-
-int ab3100_event_register(struct ab3100 *ab3100,
- struct notifier_block *nb);
-int ab3100_event_unregister(struct ab3100 *ab3100,
- struct notifier_block *nb);
-
-#endif /* MFD_AB3100_H */
--
2.29.2
