Hi, On Fri, Aug 23, 2019 at 11:42:28AM +0200, meg...@megous.com wrote: > From: Ondrej Jirman <meg...@megous.com> > > Orange Pi 3 has AP6256 WiFi/BT module. WiFi part of the module is called > bcm43356 and can be used with the brcmfmac driver. The module is powered by > the two always on regulators (not AXP805). > > WiFi uses a PG port with 1.8V voltage level signals. SoC needs to be > configured so that it sets up an 1.8V input bias on this port. This is done > by the pio driver by reading the vcc-pg-supply voltage. > > You'll need a fw_bcm43456c5_ag.bin firmware file and nvram.txt > configuration that can be found in the Xulongs's repository for H6: > > https://github.com/orangepi-xunlong/OrangePiH6_external/tree/master/ap6256 > > Mainline brcmfmac driver expects the firmware and nvram at the following > paths relative to the firmware directory: > > brcm/brcmfmac43456-sdio.bin > brcm/brcmfmac43456-sdio.txt > > Signed-off-by: Ondrej Jirman <meg...@megous.com> > --- > > Since RTC patches for H6 were merged, this can now go in too, if it looks ok. > > Other patches for this WiFi chip support were merged in previous cycles, > so this just needs enabling in DTS now. > > Sorry for the links in the commit log, but this information is useful, > even if the link itself goes bad. Any pointer what to google for > (file names, tree name) is great for anyone searching in the future.
I understand, but this should (also?) be in the wiki. Please add it
there too.
> Please take a look.
>
> Thank you,
> Ondrej
>
> .../dts/allwinner/sun50i-h6-orangepi-3.dts | 48 +++++++++++++++++++
> 1 file changed, 48 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
> b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
> index eda9d5f640b9..49d954369087 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
> @@ -56,6 +56,34 @@
> regulator-max-microvolt = <5000000>;
> regulator-always-on;
> };
> +
> + reg_vcc33_wifi: vcc33-wifi {
> + /* Always on 3.3V regulator for WiFi and BT */
> + compatible = "regulator-fixed";
> + regulator-name = "vcc33-wifi";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + vin-supply = <®_vcc5v>;
> + };
> +
> + reg_vcc_wifi_io: vcc-wifi-io {
> + /* Always on 1.8V/300mA regulator for WiFi and BT IO */
> + compatible = "regulator-fixed";
> + regulator-name = "vcc-wifi-io";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + vin-supply = <®_vcc33_wifi>;
> + };
> +
> + wifi_pwrseq: wifi_pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + clocks = <&rtc 1>;
> + clock-names = "ext_clock";
> + reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
> + post-power-on-delay-ms = <200>;
> + };
> };
>
> &cpu0 {
> @@ -91,6 +119,25 @@
> status = "okay";
> };
>
> +&mmc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc1_pins>;
This is the default already. I've removed it and applied.
Maxime
--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
signature.asc
Description: PGP signature
