On Fri, Nov 16, 2018 at 10:09:08PM +0530, Jagan Teki wrote:
> Allwinner MIPI DSI DRQ set value can be varied with respective
> video modes.
> - burst mode the set value is always 0
> - video modes whose front porch greater than 20, the set value
> can be computed based front porch and bpp.
> - video modes whose front porch is not greater than 20, the set value
> is simply 0
>
> This patch simplifies existing drq set value code by grouping
> into sun6i_dsi_get_drq and support all video modes.
>
> Signed-off-by: Jagan Teki <ja...@amarulasolutions.com>
> ---
> drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c | 38 ++++++++++++++++----------
> 1 file changed, 23 insertions(+), 15 deletions(-)
>
> diff --git a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c
> b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c
> index efd08bfd0cb8..d60955880c43 100644
> --- a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c
> +++ b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c
> @@ -363,6 +363,26 @@ static void sun6i_dsi_inst_init(struct sun6i_dsi *dsi,
> SUN6I_DSI_INST_JUMP_CFG_NUM(1));
> };
>
> +static int sun6i_dsi_get_drq(struct sun6i_dsi *dsi,
> + struct drm_display_mode *mode)
> +{
> + struct mipi_dsi_device *device = dsi->device;
> + int drq = 0;
So, here, you declaring a variable called drq, set to 0.
> + if (device->mode_flags & MIPI_DSI_MODE_VIDEO_BURST)
> + return drq;
That you return here. You could just return 0, to be clearer.
> + if ((mode->hsync_start - mode->hdisplay) > 20) {
> + /* Maaaaaagic */
> + u16 drq = (mode->hsync_start - mode->hdisplay) - 20;
You re-declare a variable with the same name here, but a different
type....
> + drq *= mipi_dsi_pixel_format_to_bpp(device->format);
> + drq /= 32;
> + }
> +
> + return drq;
And then return the first one? How is that even working?
> +
> static u16 sun6i_dsi_get_timings_vblk(struct sun6i_dsi *dsi,
> struct drm_display_mode *mode, u16 hblk)
> {
> @@ -478,21 +498,9 @@ static u16 sun6i_dsi_get_video_start_delay(struct
> sun6i_dsi *dsi,
> static void sun6i_dsi_setup_burst(struct sun6i_dsi *dsi,
> struct drm_display_mode *mode)
> {
> - struct mipi_dsi_device *device = dsi->device;
> - u32 val = 0;
> -
> - if ((mode->hsync_start - mode->hdisplay) > 20) {
> - /* Maaaaaagic */
> - u16 drq = (mode->hsync_start - mode->hdisplay) - 20;
> -
> - drq *= mipi_dsi_pixel_format_to_bpp(device->format);
> - drq /= 32;
> -
> - val = (SUN6I_DSI_TCON_DRQ_ENABLE_MODE |
> - SUN6I_DSI_TCON_DRQ_SET(drq));
> - }
> -
> - regmap_write(dsi->regs, SUN6I_DSI_TCON_DRQ_REG, val);
> + regmap_write(dsi->regs, SUN6I_DSI_TCON_DRQ_REG,
> + SUN6I_DSI_TCON_DRQ_ENABLE_MODE |
> + SUN6I_DSI_TCON_DRQ_SET(sun6i_dsi_get_drq(dsi, mode)));
On top of that, you now enable the DRQ stuff all the time, while it
was conditional before.
--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
signature.asc
Description: PGP signature
