Hi Krzysztof,
On 2018-09-05 19:40, Krzysztof Kozlowski wrote:
> The SDHCI standard, MMC host controller bindings and MMC core defines
> card detect pin as active low. Therefore there is no point to invert it
> twice.
>
> Signed-off-by: Krzysztof Kozlowski <k...@kernel.org>
>
> ---
>
> Tested only on Odroid U3. Tests on other platforms would be appreciated.
SD card detection still works fine on UniversalC210, Trats2 and OdroidU3
with this patch.
Tested-by: Marek Szyprowski <m.szyprow...@samsung.com>
> ---
> arch/arm/boot/dts/exynos4210-universal_c210.dts | 3 +--
> arch/arm/boot/dts/exynos4412-midas.dtsi | 3 +--
> arch/arm/boot/dts/exynos4412-odroid-common.dtsi | 3 +--
> 3 files changed, 3 insertions(+), 6 deletions(-)
>
> diff --git a/arch/arm/boot/dts/exynos4210-universal_c210.dts
> b/arch/arm/boot/dts/exynos4210-universal_c210.dts
> index 4e6ff97e1ec4..249bfbff1e20 100644
> --- a/arch/arm/boot/dts/exynos4210-universal_c210.dts
> +++ b/arch/arm/boot/dts/exynos4210-universal_c210.dts
> @@ -537,8 +537,7 @@
> pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4>;
> pinctrl-names = "default";
> vmmc-supply = <&ldo5_reg>;
> - cd-gpios = <&gpx3 4 GPIO_ACTIVE_HIGH>;
> - cd-inverted;
> + cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>;
> status = "okay";
> };
>
> diff --git a/arch/arm/boot/dts/exynos4412-midas.dtsi
> b/arch/arm/boot/dts/exynos4412-midas.dtsi
> index c0476c290977..aed2f2e2b0d1 100644
> --- a/arch/arm/boot/dts/exynos4412-midas.dtsi
> +++ b/arch/arm/boot/dts/exynos4412-midas.dtsi
> @@ -1269,8 +1269,7 @@
>
> &sdhci_2 {
> bus-width = <4>;
> - cd-gpios = <&gpx3 4 GPIO_ACTIVE_HIGH>;
> - cd-inverted;
> + cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>;
> pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sdhci2_cd>;
> pinctrl-names = "default";
> vmmc-supply = <&ldo21_reg>;
> diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
> b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
> index a09e46c9dbc0..2caa3132f34e 100644
> --- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
> +++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
> @@ -539,8 +539,7 @@
> pinctrl-names = "default";
> vmmc-supply = <&ldo21_reg>;
> vqmmc-supply = <&ldo4_reg>;
> - cd-gpios = <&gpk2 2 GPIO_ACTIVE_HIGH>;
> - cd-inverted;
> + cd-gpios = <&gpk2 2 GPIO_ACTIVE_LOW>;
> status = "okay";
> };
>
Best regards
--
Marek Szyprowski, PhD
Samsung R&D Institute Poland
