Hi Tony,
I have a few points regarding the various Rockchip PMIC variants and
it's handling in this driver.
Am 24.08.18 um 05:30 schrieb Tony Xie:
> Add support for the rk809 and rk817 regulator driver.
> Their specifications are as follows：
> 1、The RK809 and RK809 consist of 5 DCDCs, 9 LDOs
> and have the same registers for these components except dcdc5.
> 2、The dcdc5 is a boost dcdc for RK817 and is a buck for RK809.
> 3、The RK817 has one switch but The Rk809 has two.
>
> The output voltages are configurable and are meant to supply power
> to the main processor and other components.
>
> Signed-off-by: Tony Xie <tony....@rock-chips.com>
> ---
> drivers/regulator/Kconfig | 4 +-
> drivers/regulator/rk808-regulator.c | 639
> +++++++++++++++++++++++++++++++++++-
> include/linux/mfd/rk808.h | 3 +
> 3 files changed, 641 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
> index 5dbccf5..27ff89f 100644
> --- a/drivers/regulator/Kconfig
> +++ b/drivers/regulator/Kconfig
> @@ -716,11 +716,11 @@ config REGULATOR_RC5T583
> outputs which can be controlled by i2c communication.
>
> config REGULATOR_RK808
> - tristate "Rockchip RK805/RK808/RK818 Power regulators"
> + tristate "Rockchip RK805/RK808/RK809/RK817/RK818 Power regulators"
> depends on MFD_RK808
> help
> Select this option to enable the power regulator of ROCKCHIP
> - PMIC RK805,RK808 and RK818.
> + PMIC RK805,RK809&RK817,RK808 and RK818.
> This driver supports the control of different power rails of device
> through regulator interface. The device supports multiple DCDC/LDO
> outputs which can be controlled by i2c communication.
> diff --git a/drivers/regulator/rk808-regulator.c
> b/drivers/regulator/rk808-regulator.c
> index 213b687..4aa2df6 100644
> --- a/drivers/regulator/rk808-regulator.c
> +++ b/drivers/regulator/rk808-regulator.c
> @@ -36,6 +36,12 @@
> #define RK808_BUCK4_VSEL_MASK 0xf
> #define RK808_LDO_VSEL_MASK 0x1f
>
> +#define RK809_BUCK5_VSEL_MASK 0x7
> +
> +#define RK817_LDO_VSEL_MASK 0x7f
> +#define RK817_BOOST_VSEL_MASK 0x7
> +#define RK817_BUCK_VSEL_MASK 0x7f
> +
> #define RK818_BUCK_VSEL_MASK 0x3f
> #define RK818_BUCK4_VSEL_MASK 0x1f
> #define RK818_LDO_VSEL_MASK 0x1f
> @@ -65,6 +71,9 @@
> /* max steps for increase voltage of Buck1/2, equal 100mv*/
> #define MAX_STEPS_ONE_TIME 8
>
> +#define ENABLE_MASK(id) (BIT(id) | BIT(4 + (id)))
> +#define DISABLE_VAL(id) (BIT(4 + (id)))
> +
> #define RK805_DESC(_id, _match, _supply, _min, _max, _step, _vreg, \
> _vmask, _ereg, _emask, _etime) \
> [_id] = { \
> @@ -86,6 +95,70 @@
> .ops = &rk805_reg_ops, \
> }
>
> +#define RK817_DESC(_id, _match, _supply, _min, _max, _step, _vreg, \
> + _vmask, _ereg, _emask, _enval, _disval, _etime) \
> + { \
> + .name = (_match), \
> + .supply_name = (_supply), \
> + .of_match = of_match_ptr(_match), \
> + .regulators_node = of_match_ptr("regulators"), \
> + .type = REGULATOR_VOLTAGE, \
> + .id = (_id), \
> + .n_voltages = (((_max) - (_min)) / (_step) + 1), \
> + .owner = THIS_MODULE, \
> + .min_uV = (_min) * 1000, \
> + .uV_step = (_step) * 1000, \
> + .vsel_reg = (_vreg), \
> + .vsel_mask = (_vmask), \
> + .enable_reg = (_ereg), \
> + .enable_mask = (_emask), \
> + .enable_val = (_enval), \
> + .disable_val = (_disval), \
> + .enable_time = (_etime), \
> + .ops = &rk817_reg_ops, \
> + }
There is already a RK805_DESC and RK8XX_DESC which looking very similar.
So instead of creating a new RK817_DESC, you can also reuse the
RK8XX_DESC by extending it with a an ops parameter. I think you can
refactor the RK8XX_DESC in a way it will be usable for most of your PMICs.
It also looks like you can remove the _enval and _disval parameters
since _enval and _emask is always the same.
> +
> +#define RK817_BOOST_DESC(_id, _match, _supply, _min, _max, _step, _vreg,\
> + _vmask, _ereg, _emask, _enval, _disval, _etime, m_drop) \
> + { \
> + .name = (_match), \
> + .supply_name = (_supply), \
> + .of_match = of_match_ptr(_match), \
> + .regulators_node = of_match_ptr("regulators"), \
> + .type = REGULATOR_VOLTAGE, \
> + .id = (_id), \
> + .n_voltages = (((_max) - (_min)) / (_step) + 1), \
> + .owner = THIS_MODULE, \
> + .min_uV = (_min) * 1000, \
> + .uV_step = (_step) * 1000, \
> + .vsel_reg = (_vreg), \
> + .vsel_mask = (_vmask), \
> + .enable_reg = (_ereg), \
> + .enable_mask = (_emask), \
> + .enable_val = (_enval), \
> + .disable_val = (_disval), \
> + .enable_time = (_etime), \
> + .min_dropout_uV = (m_drop) * 1000, \
> + .ops = &rk817_boost_ops, \
> + }
> +
> +#define RK817_DESC_SWITCH(_id, _match, _supply, _ereg, _emask,\
> + _enval, _disval) \
> + { \
> + .name = (_match), \
> + .supply_name = (_supply), \
> + .of_match = of_match_ptr(_match), \
> + .regulators_node = of_match_ptr("regulators"), \
> + .type = REGULATOR_VOLTAGE, \
> + .id = (_id), \
> + .enable_reg = (_ereg), \
> + .enable_mask = (_emask), \
> + .enable_val = (_enval), \
> + .disable_val = (_disval), \
> + .owner = THIS_MODULE, \
> + .ops = &rk817_switch_ops \
> + }
Same thing applies to the RK817_DESC_SWITCH.
Regards,
Wadim
> +
> #define RK8XX_DESC(_id, _match, _supply, _min, _max, _step, _vreg, \
> _vmask, _ereg, _emask, _etime) \
> [_id] = { \
> @@ -121,7 +194,6 @@
> .ops = &rk808_switch_ops \
> }
>
> -
> struct rk808_regulator_data {
> struct gpio_desc *dvs_gpio[2];
> };
> @@ -138,6 +210,51 @@ struct rk808_regulator_data {
> REGULATOR_LINEAR_RANGE(2500000, 15, 15, 0),
> };
>
> +#define RK809_BUCK5_SEL_CNT (8)
> +
> +static const struct regulator_linear_range rk809_buck5_voltage_ranges[] = {
> + REGULATOR_LINEAR_RANGE(1500000, 0, 0, 0),
> + REGULATOR_LINEAR_RANGE(1800000, 1, 3, 200000),
> + REGULATOR_LINEAR_RANGE(2800000, 4, 5, 200000),
> + REGULATOR_LINEAR_RANGE(3300000, 6, 7, 300000),
> +};
> +
> +#define RK817_BUCK1_MIN0 500000
> +#define RK817_BUCK1_MAX0 1500000
> +
> +#define RK817_BUCK1_MIN1 1600000
> +#define RK817_BUCK1_MAX1 2400000
> +
> +#define RK817_BUCK3_MAX1 3400000
> +
> +#define RK817_BUCK1_STP0 12500
> +#define RK817_BUCK1_STP1 100000
> +
> +#define RK817_BUCK1_SEL0 ((RK817_BUCK1_MAX0 - RK817_BUCK1_MIN0) /\
> + RK817_BUCK1_STP0)
> +#define RK817_BUCK1_SEL1 ((RK817_BUCK1_MAX1 - RK817_BUCK1_MIN1) /\
> + RK817_BUCK1_STP1)
> +
> +#define RK817_BUCK3_SEL1 ((RK817_BUCK3_MAX1 - RK817_BUCK1_MIN1) /\
> + RK817_BUCK1_STP1)
> +
> +#define RK817_BUCK1_SEL_CNT (RK817_BUCK1_SEL0 + RK817_BUCK1_SEL1 + 1)
> +#define RK817_BUCK3_SEL_CNT (RK817_BUCK1_SEL0 + RK817_BUCK3_SEL1 + 1)
> +
> +static const struct regulator_linear_range rk817_buck1_voltage_ranges[] = {
> + REGULATOR_LINEAR_RANGE(RK817_BUCK1_MIN0, 0,
> + RK817_BUCK1_SEL0, RK817_BUCK1_STP0),
> + REGULATOR_LINEAR_RANGE(RK817_BUCK1_MIN1, RK817_BUCK1_SEL0 + 1,
> + RK817_BUCK1_SEL_CNT, RK817_BUCK1_STP1),
> +};
> +
> +static const struct regulator_linear_range rk817_buck3_voltage_ranges[] = {
> + REGULATOR_LINEAR_RANGE(RK817_BUCK1_MIN0, 0,
> + RK817_BUCK1_SEL0, RK817_BUCK1_STP0),
> + REGULATOR_LINEAR_RANGE(RK817_BUCK1_MIN1, RK817_BUCK1_SEL0 + 1,
> + RK817_BUCK3_SEL_CNT, RK817_BUCK1_STP1),
> +};
> +
> static int rk808_buck1_2_get_voltage_sel_regmap(struct regulator_dev *rdev)
> {
> struct rk808_regulator_data *pdata = rdev_get_drvdata(rdev);
> @@ -281,14 +398,45 @@ static int rk808_set_ramp_delay(struct regulator_dev
> *rdev, int ramp_delay)
> case 6001 ... 10000:
> break;
> default:
> - pr_warn("%s ramp_delay: %d not supported, setting 10000\n",
> - rdev->desc->name, ramp_delay);
> + dev_warn(&rdev->dev,
> + "%s ramp_delay: %d not supported, setting 10000\n",
> + rdev->desc->name, ramp_delay);
> }
>
> return regmap_update_bits(rdev->regmap, reg,
> RK808_RAMP_RATE_MASK, ramp_value);
> }
>
> +/*
> + * RK817 RK809
> + */
> +static int rk817_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay)
> +{
> + unsigned int ramp_value = RK817_RAMP_RATE_25MV_PER_US;
> + unsigned int reg = RK817_BUCK_CONFIG_REG(rdev_get_id(rdev));
> +
> + switch (ramp_delay) {
> + case 0 ... 3000:
> + ramp_value = RK817_RAMP_RATE_3MV_PER_US;
> + break;
> + case 3001 ... 6300:
> + ramp_value = RK817_RAMP_RATE_6_3MV_PER_US;
> + break;
> + case 6301 ... 12500:
> + ramp_value = RK817_RAMP_RATE_12_5MV_PER_US;
> + break;
> + case 12501 ... 25000:
> + break;
> + default:
> + dev_warn(&rdev->dev,
> + "%s ramp_delay: %d not supported, setting 10000\n",
> + rdev->desc->name, ramp_delay);
> + }
> +
> + return regmap_update_bits(rdev->regmap, reg,
> + RK817_RAMP_RATE_MASK, ramp_value);
> +}
> +
> static int rk808_set_suspend_voltage(struct regulator_dev *rdev, int uv)
> {
> unsigned int reg;
> @@ -304,6 +452,29 @@ static int rk808_set_suspend_voltage(struct
> regulator_dev *rdev, int uv)
> sel);
> }
>
> +static int rk817_check_suspend_voltage(int id)
> +{
> + if (id >= RK817_ID_DCDC1 && id <= RK817_ID_LDO9)
> + return 0;
> + return -1;
> +}
> +
> +static int rk817_set_suspend_voltage(struct regulator_dev *rdev, int uv)
> +{
> + unsigned int reg;
> + int id = rdev_get_id(rdev);
> + int sel = regulator_map_voltage_linear(rdev, uv, uv);
> + /* only ldo1~ldo9 */
> + if (sel < 0 || rk817_check_suspend_voltage(id))
> + return -EINVAL;
> +
> + reg = rdev->desc->vsel_reg + RK808_SLP_REG_OFFSET;
> +
> + return regmap_update_bits(rdev->regmap, reg,
> + rdev->desc->vsel_mask,
> + sel);
> +}
> +
> static int rk808_set_suspend_voltage_range(struct regulator_dev *rdev, int
> uv)
> {
> unsigned int reg;
> @@ -363,6 +534,129 @@ static int rk808_set_suspend_disable(struct
> regulator_dev *rdev)
> rdev->desc->enable_mask);
> }
>
> +static int rk817_set_suspend_enable_ctrl(struct regulator_dev *rdev,
> + unsigned int en)
> +{
> + unsigned int reg;
> + int id = rdev_get_id(rdev);
> + unsigned int id_slp, msk, val;
> +
> + if (id >= RK817_ID_DCDC1 && id <= RK817_ID_DCDC4)
> + id_slp = id;
> + else if (id >= RK817_ID_LDO1 && id <= RK817_ID_LDO8)
> + id_slp = 8 + (id - RK817_ID_LDO1);
> + else if (id >= RK817_ID_LDO9 && id <= RK809_ID_SW2)
> + id_slp = 4 + (id - RK817_ID_LDO9);
> + else
> + return -EINVAL;
> +
> + reg = RK817_POWER_SLP_EN_REG(id_slp / 8);
> +
> + msk = BIT(id_slp % 8);
> + if (en)
> + val = msk;
> + else
> + val = 0;
> +
> + return regmap_update_bits(rdev->regmap, reg, msk, val);
> +}
> +
> +static int rk817_set_suspend_enable(struct regulator_dev *rdev)
> +{
> + return rk817_set_suspend_enable_ctrl(rdev, 1);
> +}
> +
> +static int rk817_set_suspend_disable(struct regulator_dev *rdev)
> +{
> + return rk817_set_suspend_enable_ctrl(rdev, 0);
> +}
> +
> +static int rk8xx_set_suspend_mode(struct regulator_dev *rdev, unsigned int
> mode)
> +{
> + unsigned int reg;
> +
> + reg = rdev->desc->vsel_reg + RK808_SLP_REG_OFFSET;
> +
> + switch (mode) {
> + case REGULATOR_MODE_FAST:
> + return regmap_update_bits(rdev->regmap, reg,
> + PWM_MODE_MSK, FPWM_MODE);
> + case REGULATOR_MODE_NORMAL:
> + return regmap_update_bits(rdev->regmap, reg,
> + PWM_MODE_MSK, AUTO_PWM_MODE);
> + default:
> + dev_err(&rdev->dev, "do not support this mode\n");
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +static int rk8xx_set_mode(struct regulator_dev *rdev, unsigned int mode)
> +{
> + switch (mode) {
> + case REGULATOR_MODE_FAST:
> + return regmap_update_bits(rdev->regmap, rdev->desc->vsel_reg,
> + PWM_MODE_MSK, FPWM_MODE);
> + case REGULATOR_MODE_NORMAL:
> + return regmap_update_bits(rdev->regmap, rdev->desc->vsel_reg,
> + PWM_MODE_MSK, AUTO_PWM_MODE);
> + default:
> + dev_err(&rdev->dev, "do not support this mode\n");
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +static unsigned int rk8xx_get_mode(struct regulator_dev *rdev)
> +{
> + unsigned int val;
> + int err;
> +
> + err = regmap_read(rdev->regmap, rdev->desc->vsel_reg, &val);
> + if (err)
> + return err;
> +
> + if (val & FPWM_MODE)
> + return REGULATOR_MODE_FAST;
> + else
> + return REGULATOR_MODE_NORMAL;
> +}
> +
> +static int rk8xx_is_enabled_wmsk_regmap(struct regulator_dev *rdev)
> +{
> + unsigned int val;
> + int ret;
> +
> + ret = regmap_read(rdev->regmap, rdev->desc->enable_reg, &val);
> + if (ret != 0)
> + return ret;
> +
> + /* add write mask bit */
> + val |= (rdev->desc->enable_mask & 0xf0);
> + val &= rdev->desc->enable_mask;
> +
> + if (rdev->desc->enable_is_inverted) {
> + if (rdev->desc->enable_val)
> + return val != rdev->desc->enable_val;
> + return (val == 0);
> + }
> + if (rdev->desc->enable_val)
> + return val == rdev->desc->enable_val;
> + return val != 0;
> +}
> +
> +static unsigned int rk8xx_regulator_of_map_mode(unsigned int mode)
> +{
> + if (mode == 1)
> + return REGULATOR_MODE_FAST;
> + if (mode == 2)
> + return REGULATOR_MODE_NORMAL;
> +
> + return -EINVAL;
> +}
> +
> static struct regulator_ops rk805_reg_ops = {
> .list_voltage = regulator_list_voltage_linear,
> .map_voltage = regulator_map_voltage_linear,
> @@ -433,6 +727,71 @@ static int rk808_set_suspend_disable(struct
> regulator_dev *rdev)
> .set_suspend_disable = rk808_set_suspend_disable,
> };
>
> +static struct regulator_ops rk809_buck5_ops_range = {
> + .list_voltage = regulator_list_voltage_linear_range,
> + .map_voltage = regulator_map_voltage_linear_range,
> + .get_voltage_sel = regulator_get_voltage_sel_regmap,
> + .set_voltage_sel = regulator_set_voltage_sel_regmap,
> + .set_voltage_time_sel = regulator_set_voltage_time_sel,
> + .enable = regulator_enable_regmap,
> + .disable = regulator_disable_regmap,
> + .is_enabled = rk8xx_is_enabled_wmsk_regmap,
> + .set_suspend_voltage = rk808_set_suspend_voltage_range,
> + .set_suspend_enable = rk817_set_suspend_enable,
> + .set_suspend_disable = rk817_set_suspend_disable,
> +};
> +
> +static struct regulator_ops rk817_reg_ops = {
> + .list_voltage = regulator_list_voltage_linear,
> + .map_voltage = regulator_map_voltage_linear,
> + .get_voltage_sel = regulator_get_voltage_sel_regmap,
> + .set_voltage_sel = regulator_set_voltage_sel_regmap,
> + .enable = regulator_enable_regmap,
> + .disable = regulator_disable_regmap,
> + .is_enabled = rk8xx_is_enabled_wmsk_regmap,
> + .set_suspend_voltage = rk817_set_suspend_voltage,
> + .set_suspend_enable = rk817_set_suspend_enable,
> + .set_suspend_disable = rk817_set_suspend_disable,
> +};
> +
> +static struct regulator_ops rk817_boost_ops = {
> + .list_voltage = regulator_list_voltage_linear,
> + .map_voltage = regulator_map_voltage_linear,
> + .get_voltage_sel = regulator_get_voltage_sel_regmap,
> + .set_voltage_sel = regulator_set_voltage_sel_regmap,
> + .enable = regulator_enable_regmap,
> + .disable = regulator_disable_regmap,
> + .is_enabled = rk8xx_is_enabled_wmsk_regmap,
> + .set_suspend_enable = rk817_set_suspend_enable,
> + .set_suspend_disable = rk817_set_suspend_disable,
> +};
> +
> +static struct regulator_ops rk817_buck_ops_range = {
> + .list_voltage = regulator_list_voltage_linear_range,
> + .map_voltage = regulator_map_voltage_linear_range,
> + .get_voltage_sel = regulator_get_voltage_sel_regmap,
> + .set_voltage_sel = regulator_set_voltage_sel_regmap,
> + .set_voltage_time_sel = regulator_set_voltage_time_sel,
> + .enable = regulator_enable_regmap,
> + .disable = regulator_disable_regmap,
> + .is_enabled = rk8xx_is_enabled_wmsk_regmap,
> + .set_mode = rk8xx_set_mode,
> + .get_mode = rk8xx_get_mode,
> + .set_suspend_mode = rk8xx_set_suspend_mode,
> + .set_ramp_delay = rk817_set_ramp_delay,
> + .set_suspend_voltage = rk808_set_suspend_voltage_range,
> + .set_suspend_enable = rk817_set_suspend_enable,
> + .set_suspend_disable = rk817_set_suspend_disable,
> +};
> +
> +static struct regulator_ops rk817_switch_ops = {
> + .enable = regulator_enable_regmap,
> + .disable = regulator_disable_regmap,
> + .is_enabled = regulator_is_enabled_regmap,
> + .set_suspend_enable = rk817_set_suspend_enable,
> + .set_suspend_disable = rk817_set_suspend_disable,
> +};
> +
> static const struct regulator_desc rk805_reg[] = {
> {
> .name = "DCDC_REG1",
> @@ -589,6 +948,271 @@ static int rk808_set_suspend_disable(struct
> regulator_dev *rdev)
> RK808_DCDC_EN_REG, BIT(6)),
> };
>
> +static const struct regulator_desc rk809_reg[] = {
> + {
> + .name = "DCDC_REG1",
> + .supply_name = "vcc1",
> + .of_match = of_match_ptr("DCDC_REG1"),
> + .regulators_node = of_match_ptr("regulators"),
> + .id = RK817_ID_DCDC1,
> + .ops = &rk817_buck_ops_range,
> + .type = REGULATOR_VOLTAGE,
> + .n_voltages = RK817_BUCK1_SEL_CNT + 1,
> + .linear_ranges = rk817_buck1_voltage_ranges,
> + .n_linear_ranges = ARRAY_SIZE(rk817_buck1_voltage_ranges),
> + .vsel_reg = RK817_BUCK1_ON_VSEL_REG,
> + .vsel_mask = RK817_BUCK_VSEL_MASK,
> + .enable_reg = RK817_POWER_EN_REG(0),
> + .enable_mask = ENABLE_MASK(RK817_ID_DCDC1),
> + .enable_val = ENABLE_MASK(RK817_ID_DCDC1),
> + .disable_val = DISABLE_VAL(RK817_ID_DCDC1),
> + .of_map_mode = rk8xx_regulator_of_map_mode,
> + .owner = THIS_MODULE,
> + }, {
> + .name = "DCDC_REG2",
> + .supply_name = "vcc2",
> + .of_match = of_match_ptr("DCDC_REG2"),
> + .regulators_node = of_match_ptr("regulators"),
> + .id = RK817_ID_DCDC2,
> + .ops = &rk817_buck_ops_range,
> + .type = REGULATOR_VOLTAGE,
> + .n_voltages = RK817_BUCK1_SEL_CNT + 1,
> + .linear_ranges = rk817_buck1_voltage_ranges,
> + .n_linear_ranges = ARRAY_SIZE(rk817_buck1_voltage_ranges),
> + .vsel_reg = RK817_BUCK2_ON_VSEL_REG,
> + .vsel_mask = RK817_BUCK_VSEL_MASK,
> + .enable_reg = RK817_POWER_EN_REG(0),
> + .enable_mask = ENABLE_MASK(RK817_ID_DCDC2),
> + .enable_val = ENABLE_MASK(RK817_ID_DCDC2),
> + .disable_val = DISABLE_VAL(RK817_ID_DCDC2),
> + .of_map_mode = rk8xx_regulator_of_map_mode,
> + .owner = THIS_MODULE,
> + }, {
> + .name = "DCDC_REG3",
> + .supply_name = "vcc3",
> + .of_match = of_match_ptr("DCDC_REG3"),
> + .regulators_node = of_match_ptr("regulators"),
> + .id = RK817_ID_DCDC3,
> + .ops = &rk817_buck_ops_range,
> + .type = REGULATOR_VOLTAGE,
> + .n_voltages = RK817_BUCK1_SEL_CNT + 1,
> + .linear_ranges = rk817_buck1_voltage_ranges,
> + .n_linear_ranges = ARRAY_SIZE(rk817_buck1_voltage_ranges),
> + .vsel_reg = RK817_BUCK3_ON_VSEL_REG,
> + .vsel_mask = RK817_BUCK_VSEL_MASK,
> + .enable_reg = RK817_POWER_EN_REG(0),
> + .enable_mask = ENABLE_MASK(RK817_ID_DCDC3),
> + .enable_val = ENABLE_MASK(RK817_ID_DCDC3),
> + .disable_val = DISABLE_VAL(RK817_ID_DCDC3),
> + .of_map_mode = rk8xx_regulator_of_map_mode,
> + .owner = THIS_MODULE,
> + }, {
> + .name = "DCDC_REG4",
> + .supply_name = "vcc4",
> + .of_match = of_match_ptr("DCDC_REG4"),
> + .regulators_node = of_match_ptr("regulators"),
> + .id = RK817_ID_DCDC4,
> + .ops = &rk817_buck_ops_range,
> + .type = REGULATOR_VOLTAGE,
> + .n_voltages = RK817_BUCK3_SEL_CNT + 1,
> + .linear_ranges = rk817_buck3_voltage_ranges,
> + .n_linear_ranges = ARRAY_SIZE(rk817_buck3_voltage_ranges),
> + .vsel_reg = RK817_BUCK4_ON_VSEL_REG,
> + .vsel_mask = RK817_BUCK_VSEL_MASK,
> + .enable_reg = RK817_POWER_EN_REG(0),
> + .enable_mask = ENABLE_MASK(RK817_ID_DCDC4),
> + .enable_val = ENABLE_MASK(RK817_ID_DCDC4),
> + .disable_val = DISABLE_VAL(RK817_ID_DCDC4),
> + .of_map_mode = rk8xx_regulator_of_map_mode,
> + .owner = THIS_MODULE,
> + },
> + {
> + .name = "DCDC_REG5",
> + .supply_name = "vcc9",
> + .of_match = of_match_ptr("DCDC_REG5"),
> + .regulators_node = of_match_ptr("regulators"),
> + .id = RK809_ID_DCDC5,
> + .ops = &rk809_buck5_ops_range,
> + .type = REGULATOR_VOLTAGE,
> + .n_voltages = RK809_BUCK5_SEL_CNT,
> + .linear_ranges = rk809_buck5_voltage_ranges,
> + .n_linear_ranges = ARRAY_SIZE(rk809_buck5_voltage_ranges),
> + .vsel_reg = RK809_BUCK5_CONFIG(0),
> + .vsel_mask = RK809_BUCK5_VSEL_MASK,
> + .enable_reg = RK817_POWER_EN_REG(3),
> + .enable_mask = ENABLE_MASK(1),
> + .enable_val = ENABLE_MASK(1),
> + .disable_val = DISABLE_VAL(1),
> + .of_map_mode = rk8xx_regulator_of_map_mode,
> + .owner = THIS_MODULE,
> + },
> + RK817_DESC(RK817_ID_LDO1, "LDO_REG1", "vcc5", 600, 3400, 25,
> + RK817_LDO_ON_VSEL_REG(0), RK817_LDO_VSEL_MASK,
> + RK817_POWER_EN_REG(1), ENABLE_MASK(0), ENABLE_MASK(0),
> + DISABLE_VAL(0), 400),
> + RK817_DESC(RK817_ID_LDO2, "LDO_REG2", "vcc5", 600, 3400, 25,
> + RK817_LDO_ON_VSEL_REG(1), RK817_LDO_VSEL_MASK,
> + RK817_POWER_EN_REG(1), ENABLE_MASK(1), ENABLE_MASK(1),
> + DISABLE_VAL(1), 400),
> + RK817_DESC(RK817_ID_LDO3, "LDO_REG3", "vcc5", 600, 3400, 25,
> + RK817_LDO_ON_VSEL_REG(2), RK817_LDO_VSEL_MASK,
> + RK817_POWER_EN_REG(1), ENABLE_MASK(2), ENABLE_MASK(2),
> + DISABLE_VAL(2), 400),
> + RK817_DESC(RK817_ID_LDO4, "LDO_REG4", "vcc6", 600, 3400, 25,
> + RK817_LDO_ON_VSEL_REG(3), RK817_LDO_VSEL_MASK,
> + RK817_POWER_EN_REG(1), ENABLE_MASK(3), ENABLE_MASK(3),
> + DISABLE_VAL(3), 400),
> + RK817_DESC(RK817_ID_LDO5, "LDO_REG5", "vcc6", 600, 3400, 25,
> + RK817_LDO_ON_VSEL_REG(4), RK817_LDO_VSEL_MASK,
> + RK817_POWER_EN_REG(2), ENABLE_MASK(0), ENABLE_MASK(0),
> + DISABLE_VAL(0), 400),
> + RK817_DESC(RK817_ID_LDO6, "LDO_REG6", "vcc6", 600, 3400, 25,
> + RK817_LDO_ON_VSEL_REG(5), RK817_LDO_VSEL_MASK,
> + RK817_POWER_EN_REG(2), ENABLE_MASK(1), ENABLE_MASK(1),
> + DISABLE_VAL(1), 400),
> + RK817_DESC(RK817_ID_LDO7, "LDO_REG7", "vcc7", 600, 3400, 25,
> + RK817_LDO_ON_VSEL_REG(6), RK817_LDO_VSEL_MASK,
> + RK817_POWER_EN_REG(2), ENABLE_MASK(2), ENABLE_MASK(2),
> + DISABLE_VAL(2), 400),
> + RK817_DESC(RK817_ID_LDO8, "LDO_REG8", "vcc7", 600, 3400, 25,
> + RK817_LDO_ON_VSEL_REG(7), RK817_LDO_VSEL_MASK,
> + RK817_POWER_EN_REG(2), ENABLE_MASK(3), ENABLE_MASK(3),
> + DISABLE_VAL(3), 400),
> + RK817_DESC(RK817_ID_LDO9, "LDO_REG9", "vcc7", 600, 3400, 25,
> + RK817_LDO_ON_VSEL_REG(8), RK817_LDO_VSEL_MASK,
> + RK817_POWER_EN_REG(3), ENABLE_MASK(0), ENABLE_MASK(0),
> + DISABLE_VAL(0), 400),
> + RK817_DESC_SWITCH(RK809_ID_SW1, "SWITCH_REG1", "vcc9",
> + RK817_POWER_EN_REG(3), ENABLE_MASK(2),
> + ENABLE_MASK(2), DISABLE_VAL(2)),
> + RK817_DESC_SWITCH(RK809_ID_SW2, "SWITCH_REG2", "vcc8",
> + RK817_POWER_EN_REG(3), ENABLE_MASK(3),
> + ENABLE_MASK(3), DISABLE_VAL(3)),
> +};
> +
> +static const struct regulator_desc rk817_reg[] = {
> + {
> + .name = "DCDC_REG1",
> + .supply_name = "vcc1",
> + .of_match = of_match_ptr("DCDC_REG1"),
> + .regulators_node = of_match_ptr("regulators"),
> + .id = RK817_ID_DCDC1,
> + .ops = &rk817_buck_ops_range,
> + .type = REGULATOR_VOLTAGE,
> + .n_voltages = RK817_BUCK1_SEL_CNT + 1,
> + .linear_ranges = rk817_buck1_voltage_ranges,
> + .n_linear_ranges = ARRAY_SIZE(rk817_buck1_voltage_ranges),
> + .vsel_reg = RK817_BUCK1_ON_VSEL_REG,
> + .vsel_mask = RK817_BUCK_VSEL_MASK,
> + .enable_reg = RK817_POWER_EN_REG(0),
> + .enable_mask = ENABLE_MASK(RK817_ID_DCDC1),
> + .enable_val = ENABLE_MASK(RK817_ID_DCDC1),
> + .disable_val = DISABLE_VAL(RK817_ID_DCDC1),
> + .of_map_mode = rk8xx_regulator_of_map_mode,
> + .owner = THIS_MODULE,
> + }, {
> + .name = "DCDC_REG2",
> + .supply_name = "vcc2",
> + .of_match = of_match_ptr("DCDC_REG2"),
> + .regulators_node = of_match_ptr("regulators"),
> + .id = RK817_ID_DCDC2,
> + .ops = &rk817_buck_ops_range,
> + .type = REGULATOR_VOLTAGE,
> + .n_voltages = RK817_BUCK1_SEL_CNT + 1,
> + .linear_ranges = rk817_buck1_voltage_ranges,
> + .n_linear_ranges = ARRAY_SIZE(rk817_buck1_voltage_ranges),
> + .vsel_reg = RK817_BUCK2_ON_VSEL_REG,
> + .vsel_mask = RK817_BUCK_VSEL_MASK,
> + .enable_reg = RK817_POWER_EN_REG(0),
> + .enable_mask = ENABLE_MASK(RK817_ID_DCDC2),
> + .enable_val = ENABLE_MASK(RK817_ID_DCDC2),
> + .disable_val = DISABLE_VAL(RK817_ID_DCDC2),
> + .of_map_mode = rk8xx_regulator_of_map_mode,
> + .owner = THIS_MODULE,
> + }, {
> + .name = "DCDC_REG3",
> + .supply_name = "vcc3",
> + .of_match = of_match_ptr("DCDC_REG3"),
> + .regulators_node = of_match_ptr("regulators"),
> + .id = RK817_ID_DCDC3,
> + .ops = &rk817_buck_ops_range,
> + .type = REGULATOR_VOLTAGE,
> + .n_voltages = RK817_BUCK1_SEL_CNT + 1,
> + .linear_ranges = rk817_buck1_voltage_ranges,
> + .n_linear_ranges = ARRAY_SIZE(rk817_buck1_voltage_ranges),
> + .vsel_reg = RK817_BUCK3_ON_VSEL_REG,
> + .vsel_mask = RK817_BUCK_VSEL_MASK,
> + .enable_reg = RK817_POWER_EN_REG(0),
> + .enable_mask = ENABLE_MASK(RK817_ID_DCDC3),
> + .enable_val = ENABLE_MASK(RK817_ID_DCDC3),
> + .disable_val = DISABLE_VAL(RK817_ID_DCDC3),
> + .of_map_mode = rk8xx_regulator_of_map_mode,
> + .owner = THIS_MODULE,
> + }, {
> + .name = "DCDC_REG4",
> + .supply_name = "vcc4",
> + .of_match = of_match_ptr("DCDC_REG4"),
> + .regulators_node = of_match_ptr("regulators"),
> + .id = RK817_ID_DCDC4,
> + .ops = &rk817_buck_ops_range,
> + .type = REGULATOR_VOLTAGE,
> + .n_voltages = RK817_BUCK3_SEL_CNT + 1,
> + .linear_ranges = rk817_buck3_voltage_ranges,
> + .n_linear_ranges = ARRAY_SIZE(rk817_buck3_voltage_ranges),
> + .vsel_reg = RK817_BUCK4_ON_VSEL_REG,
> + .vsel_mask = RK817_BUCK_VSEL_MASK,
> + .enable_reg = RK817_POWER_EN_REG(0),
> + .enable_mask = ENABLE_MASK(RK817_ID_DCDC4),
> + .enable_val = ENABLE_MASK(RK817_ID_DCDC4),
> + .disable_val = DISABLE_VAL(RK817_ID_DCDC4),
> + .of_map_mode = rk8xx_regulator_of_map_mode,
> + .owner = THIS_MODULE,
> + },
> + RK817_DESC(RK817_ID_LDO1, "LDO_REG1", "vcc5", 600, 3400, 25,
> + RK817_LDO_ON_VSEL_REG(0), RK817_LDO_VSEL_MASK,
> + RK817_POWER_EN_REG(1), ENABLE_MASK(0), ENABLE_MASK(0),
> + DISABLE_VAL(0), 400),
> + RK817_DESC(RK817_ID_LDO2, "LDO_REG2", "vcc5", 600, 3400, 25,
> + RK817_LDO_ON_VSEL_REG(1), RK817_LDO_VSEL_MASK,
> + RK817_POWER_EN_REG(1), ENABLE_MASK(1), ENABLE_MASK(1),
> + DISABLE_VAL(1), 400),
> + RK817_DESC(RK817_ID_LDO3, "LDO_REG3", "vcc5", 600, 3400, 25,
> + RK817_LDO_ON_VSEL_REG(2), RK817_LDO_VSEL_MASK,
> + RK817_POWER_EN_REG(1), ENABLE_MASK(2), ENABLE_MASK(2),
> + DISABLE_VAL(2), 400),
> + RK817_DESC(RK817_ID_LDO4, "LDO_REG4", "vcc6", 600, 3400, 25,
> + RK817_LDO_ON_VSEL_REG(3), RK817_LDO_VSEL_MASK,
> + RK817_POWER_EN_REG(1), ENABLE_MASK(3), ENABLE_MASK(3),
> + DISABLE_VAL(3), 400),
> + RK817_DESC(RK817_ID_LDO5, "LDO_REG5", "vcc6", 600, 3400, 25,
> + RK817_LDO_ON_VSEL_REG(4), RK817_LDO_VSEL_MASK,
> + RK817_POWER_EN_REG(2), ENABLE_MASK(0), ENABLE_MASK(0),
> + DISABLE_VAL(0), 400),
> + RK817_DESC(RK817_ID_LDO6, "LDO_REG6", "vcc6", 600, 3400, 25,
> + RK817_LDO_ON_VSEL_REG(5), RK817_LDO_VSEL_MASK,
> + RK817_POWER_EN_REG(2), ENABLE_MASK(1), ENABLE_MASK(1),
> + DISABLE_VAL(1), 400),
> + RK817_DESC(RK817_ID_LDO7, "LDO_REG7", "vcc7", 600, 3400, 25,
> + RK817_LDO_ON_VSEL_REG(6), RK817_LDO_VSEL_MASK,
> + RK817_POWER_EN_REG(2), ENABLE_MASK(2), ENABLE_MASK(2),
> + DISABLE_VAL(2), 400),
> + RK817_DESC(RK817_ID_LDO8, "LDO_REG8", "vcc7", 600, 3400, 25,
> + RK817_LDO_ON_VSEL_REG(7), RK817_LDO_VSEL_MASK,
> + RK817_POWER_EN_REG(2), ENABLE_MASK(3), ENABLE_MASK(3),
> + DISABLE_VAL(3), 400),
> + RK817_DESC(RK817_ID_LDO9, "LDO_REG9", "vcc7", 600, 3400, 25,
> + RK817_LDO_ON_VSEL_REG(8), RK817_LDO_VSEL_MASK,
> + RK817_POWER_EN_REG(3), ENABLE_MASK(0), ENABLE_MASK(0),
> + DISABLE_VAL(0), 400),
> + RK817_BOOST_DESC(RK817_ID_BOOST, "BOOST", "vcc8", 4700, 5400, 100,
> + RK817_BOOST_OTG_CFG, RK817_BOOST_VSEL_MASK,
> + RK817_POWER_EN_REG(3), ENABLE_MASK(1), ENABLE_MASK(1),
> + DISABLE_VAL(1), 400, 3500 - 5400),
> + RK817_DESC_SWITCH(RK817_ID_BOOST_OTG_SW, "OTG_SWITCH", "vcc9",
> + RK817_POWER_EN_REG(3), ENABLE_MASK(2),
> + ENABLE_MASK(2), DISABLE_VAL(2)),
> +};
> +
> static const struct regulator_desc rk818_reg[] = {
> {
> .name = "DCDC_REG1",
> @@ -759,6 +1383,14 @@ static int rk808_regulator_probe(struct platform_device
> *pdev)
> regulators = rk808_reg;
> nregulators = RK808_NUM_REGULATORS;
> break;
> + case RK809_ID:
> + regulators = rk809_reg;
> + nregulators = RK809_NUM_REGULATORS;
> + break;
> + case RK817_ID:
> + regulators = rk817_reg;
> + nregulators = RK817_NUM_REGULATORS;
> + break;
> case RK818_ID:
> regulators = rk818_reg;
> nregulators = RK818_NUM_REGULATORS;
> @@ -797,6 +1429,7 @@ static int rk808_regulator_probe(struct platform_device
> *pdev)
> module_platform_driver(rk808_regulator_driver);
>
> MODULE_DESCRIPTION("regulator driver for the RK808/RK818 series PMICs");
> +MODULE_AUTHOR("Tony xie <tony....@rock-chips.com>");
> MODULE_AUTHOR("Chris Zhong <z...@rock-chips.com>");
> MODULE_AUTHOR("Zhang Qing <zhangq...@rock-chips.com>");
> MODULE_AUTHOR("Wadim Egorov <w.ego...@phytec.de>");
> diff --git a/include/linux/mfd/rk808.h b/include/linux/mfd/rk808.h
> index b973b0a..b4ce2373 100644
> --- a/include/linux/mfd/rk808.h
> +++ b/include/linux/mfd/rk808.h
> @@ -396,7 +396,10 @@ enum rk805_reg {
> #define SHUTDOWN_FUN (0x2 << 2)
> #define SLEEP_FUN (0x1 << 2)
> #define RK8XX_ID_MSK 0xfff0
> +#define PWM_MODE_MSK BIT(7)
> #define FPWM_MODE BIT(7)
> +#define AUTO_PWM_MODE 0
> +
> enum rk817_reg_id {
> RK817_ID_DCDC1 = 0,
> RK817_ID_DCDC2,
