On Fri, 20 Jul 2018 17:15:14 +0200
Miquel Raynal <miquel.ray...@bootlin.com> wrote:
> Two helpers have been added to the core to make ECC-related
> configuration between the detection phase and the final NAND scan. Use
> these hooks and convert the driver to just use nand_scan() instead of
> both nand_scan_ident() and nand_scan_tail().
>
> Signed-off-by: Miquel Raynal <miquel.ray...@bootlin.com>
> ---
> drivers/mtd/nand/raw/tango_nand.c | 40
> +++++++++++++++++++++++----------------
> 1 file changed, 24 insertions(+), 16 deletions(-)
>
> diff --git a/drivers/mtd/nand/raw/tango_nand.c
> b/drivers/mtd/nand/raw/tango_nand.c
> index dd7a26efdf4f..a448d0797cd5 100644
> --- a/drivers/mtd/nand/raw/tango_nand.c
> +++ b/drivers/mtd/nand/raw/tango_nand.c
> @@ -517,6 +517,28 @@ static int tango_set_timings(struct mtd_info *mtd, int
> csline,
> return 0;
> }
>
> +static int tango_attach_chip(struct nand_chip *chip)
> +{
> + struct nand_ecc_ctrl *ecc = &chip->ecc;
> +
> + ecc->mode = NAND_ECC_HW;
> + ecc->algo = NAND_ECC_BCH;
> + ecc->bytes = DIV_ROUND_UP(ecc->strength * FIELD_ORDER, BITS_PER_BYTE);
> +
> + ecc->read_page_raw = tango_read_page_raw;
> + ecc->write_page_raw = tango_write_page_raw;
> + ecc->read_page = tango_read_page;
> + ecc->write_page = tango_write_page;
> + ecc->read_oob = tango_read_oob;
> + ecc->write_oob = tango_write_oob;
> +
> + return 0;
> +}
> +
> +static const struct nand_controller_ops tango_controller_ops = {
> + .attach_chip = tango_attach_chip,
> +};
> +
> static int chip_init(struct device *dev, struct device_node *np)
> {
> u32 cs;
> @@ -560,28 +582,14 @@ static int chip_init(struct device *dev, struct
> device_node *np)
> NAND_NO_SUBPAGE_WRITE |
> NAND_WAIT_TCCS;
> chip->controller = &nfc->hw;
> + chip->controller->ops = &tango_controller_ops;
Move this assignment here [1]. With that fixed:
Reviewed-by: Boris Brezillon <boris.brezil...@bootlin.com>
> tchip->base = nfc->pbus_base + (cs * 256);
>
> nand_set_flash_node(chip, np);
> mtd_set_ooblayout(mtd, &tango_nand_ooblayout_ops);
> mtd->dev.parent = dev;
>
> - err = nand_scan_ident(mtd, 1, NULL);
> - if (err)
> - return err;
> -
> - ecc->mode = NAND_ECC_HW;
> - ecc->algo = NAND_ECC_BCH;
> - ecc->bytes = DIV_ROUND_UP(ecc->strength * FIELD_ORDER, BITS_PER_BYTE);
> -
> - ecc->read_page_raw = tango_read_page_raw;
> - ecc->write_page_raw = tango_write_page_raw;
> - ecc->read_page = tango_read_page;
> - ecc->write_page = tango_write_page;
> - ecc->read_oob = tango_read_oob;
> - ecc->write_oob = tango_write_oob;
> -
> - err = nand_scan_tail(mtd);
> + err = nand_scan(mtd, 1);
> if (err)
> return err;
>
[1]https://elixir.bootlin.com/linux/v4.18-rc5/source/drivers/mtd/nand/raw/tango_nand.c#L657
