On Thu, Jun 21, 2018 at 08:44:59PM +0300, Andrey Gusakov wrote:
> This adds support for the Zodiac Inflight Innovations SCU2 Ethernet
> Switch Board, which is based on the i.MX51.
>
> Signed-off-by: Andrey Gusakov <andrey.gusa...@cogentembedded.com>
> ---
> arch/arm/boot/dts/Makefile | 3 +-
> arch/arm/boot/dts/imx51-zii-scu2-esb.dts | 178
> +++++++++++++++++++++++++++++++
> 2 files changed, 180 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/imx51-zii-scu2-esb.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 37a3de7..d8900f4 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -358,7 +358,8 @@ dtb-$(CONFIG_SOC_IMX51) += \
> imx51-digi-connectcore-jsk.dtb \
> imx51-eukrea-mbimxsd51-baseboard.dtb \
> imx51-ts4800.dtb \
> - imx51-zii-rdu1.dtb
> + imx51-zii-rdu1.dtb \
> + imx51-zii-scu2-esb.dtb
> dtb-$(CONFIG_SOC_IMX53) += \
> imx53-ard.dtb \
> imx53-cx9020.dtb \
> diff --git a/arch/arm/boot/dts/imx51-zii-scu2-esb.dts
> b/arch/arm/boot/dts/imx51-zii-scu2-esb.dts
> new file mode 100644
> index 0000000..e052133
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx51-zii-scu2-esb.dts
> @@ -0,0 +1,178 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +// Copyright (C) 2018 Zodiac Inflight Innovations
> +
> +/dts-v1/;
> +#include "imx51-zii-common.dtsi"
> +
> +/ {
> + model = "ZII SCU2 ESB board";
> + compatible = "zii,imx51-scu2-esb", "fsl,imx51";
> +};
> +
> +&esdhc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_esdhc1_4bit &pinctrl_esdhc1_8bit>;
> + bus-width = <8>;
> +};
> +
> +&fec {
> + phy-reset-gpios = <&gpio4 21 GPIO_ACTIVE_LOW>;
> +
> + fixed-link {
> + speed = <100>;
> + full-duplex;
> + };
> +
> + fec_mdio: mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
> +
> + switch@0 {
> + compatible = "marvell,mv88e6085";
> + reg = <0>;
> + dsa,member = <0 0>;
> + eeprom-length = <512>;
> + interrupt-parent = <&gpio4>;
> + interrupts = <20 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + label = "port1";
> + };
> +
> + port@1 {
> + reg = <1>;
> + label = "port2";
> + };
> +
> + port@2 {
> + reg = <2>;
> + label = "port3";
> + };
> +
> + port@3 {
> + reg = <3>;
> + label = "scu2scu";
> + };
> +
> + port@4 {
> + reg = <4>;
> + label = "esb2host";
> + };
Please constantly have newline between nodes.
Shawn
> + port@5 {
> + reg = <5>;
> + label = "esb2mezz";
> + phy-mode = "sgmii";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> + port@6 {
> + reg = <6>;
> + label = "cpu";
> + phy-mode = "mii";
> + ethernet = <&fec>;
> +
> + fixed-link {
> + speed = <100>;
> + full-duplex;
> + };
> + };
> + };
> + };
> + };
> +};
> +
> +&i2c2 {
> + lm75@48 {
> + compatible = "national,lm75";
> + reg = <0x48>;
> + };
> +};
> +
> +&i2c_gpio {
> + gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>, /* sda */
> + <&gpio3 0 GPIO_ACTIVE_HIGH>; /* scl */
> +};
> +
> +&ipu {
> + status = "disabled";
> +};
> +
> +&usb_vbus {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usb_mmc_reset>;
> + gpio = <&gpio4 19 GPIO_ACTIVE_LOW>;
> + startup-delay-us = <150000>;
> +};
> +
> +&iomuxc {
> + pinctrl_fec: fecgrp {
> + fsl,pins = <
> + MX51_PAD_DISP2_DAT15__FEC_TDATA0 0x2004
> + MX51_PAD_DISP2_DAT6__FEC_TDATA1 0x2004
> + MX51_PAD_DISP2_DAT7__FEC_TDATA2 0x2004
> + MX51_PAD_DISP2_DAT8__FEC_TDATA3 0x2004
> + MX51_PAD_DISP2_DAT9__FEC_TX_EN 0x2004
> + MX51_PAD_DISP2_DAT10__FEC_COL 0x0180
> + MX51_PAD_DISP2_DAT11__FEC_RX_CLK 0x0180
> + MX51_PAD_DISP2_DAT12__FEC_RX_DV 0x20a4
> + MX51_PAD_DISP2_DAT13__FEC_TX_CLK 0x2180
> + MX51_PAD_DISP2_DAT14__FEC_RDATA0 0x2180
> + MX51_PAD_DI2_DISP_CLK__FEC_RDATA1 0x0085
> + MX51_PAD_DI_GP4__FEC_RDATA2 0x0085
> + MX51_PAD_DISP2_DAT0__FEC_RDATA3 0x0085
> + MX51_PAD_DI2_PIN2__FEC_MDC 0x2004
> + MX51_PAD_DI2_PIN3__FEC_MDIO 0x01f5
> + MX51_PAD_DI2_PIN4__FEC_CRS 0x0180
> + MX51_PAD_AUD3_BB_FS__GPIO4_21 0x0000
> + >;
> + };
> +
> + pinctrl_swi2c: swi2cgrp {
> + fsl,pins = <
> + MX51_PAD_DI1_PIN11__GPIO3_0 0x100
> + MX51_PAD_DI1_PIN12__GPIO3_1 0x100
> + >;
> + };
> +
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX51_PAD_UART1_RXD__UART1_RXD 0x1c5
> + MX51_PAD_UART1_TXD__UART1_TXD 0x1c5
> + MX51_PAD_UART1_RTS__UART1_RTS 0x1c5
> + MX51_PAD_UART1_CTS__UART1_CTS 0x1c5
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX51_PAD_UART2_RXD__UART2_RXD 0x1c5
> + MX51_PAD_UART2_TXD__UART2_TXD 0x1c5
> + MX51_PAD_USBH1_DATA0__UART2_CTS 0x1c5
> + MX51_PAD_USBH1_DATA3__UART2_RTS 0x1c5
> + >;
> + };
> +
> + pinctrl_uart3: uart3grp {
> + fsl,pins = <
> + MX51_PAD_UART3_RXD__UART3_RXD 0x1c5
> + MX51_PAD_UART3_TXD__UART3_TXD 0x1c5
> + >;
> + };
> +
> + pinctrl_usb_mmc_reset: usbmmcgrp {
> + fsl,pins = <
> + MX51_PAD_AUD3_BB_RXD__GPIO4_19 0x100
> + >;
> + };
> +};
> --
> 1.9.1
>
