Hi Michel The subject of all your patches for arch/arm should start with:
ARM: dts:
A git log on that directory clearly shows that's the preferred one.
I would also say that you are missing a symbol definition in
arch/arm/mach-shmobile/Kconfig
(even if you got rid of any board file)
I would expect a symbol to select in menuconfig, with your
dependencies listed there (ie, the serial interface driver)
Something like this (I left the 'xx' out from the part name on purpose)
diff --git a/arch/arm/mach-shmobile/Kconfig b/arch/arm/mach-shmobile/Kconfig
index 280e731..9a519330 100644
--- a/arch/arm/mach-shmobile/Kconfig
+++ b/arch/arm/mach-shmobile/Kconfig
@@ -114,4 +114,8 @@ config ARCH_SH73A0
bool "SH-Mobile AG5 (R8A73A00)"
select ARCH_RMOBILE
select RENESAS_INTC_IRQPIN
+
+config ARCH_R9A06G0
+ bool "RZ/N1 (R9A06G0)"
+ select SERIAL_8250_DW
endif
But please wait for others (preferibly Geert or Simon) to confim this.
On Thu, Mar 29, 2018 at 08:47:02AM +0100, Michel Pollet wrote:
> This adds the Renesas RZ/N1 Family (Part #R9A06G0xx) SoC
> bare bone support.
>
> This currently only handles generic parts (gic, architected timer)
> and a UART.
> For simplicity sake, this also relies on the bootloader to set the
> pinctrl and clocks.
>
> Signed-off-by: Michel Pollet <michel.pol...@bp.renesas.com>
> ---
> arch/arm/boot/dts/r9a06g0xx.dtsi | 96
> ++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 96 insertions(+)
> create mode 100644 arch/arm/boot/dts/r9a06g0xx.dtsi
>
> diff --git a/arch/arm/boot/dts/r9a06g0xx.dtsi
> b/arch/arm/boot/dts/r9a06g0xx.dtsi
> new file mode 100644
> index 0000000..c6eeee3
> --- /dev/null
> +++ b/arch/arm/boot/dts/r9a06g0xx.dtsi
> @@ -0,0 +1,96 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Base Device Tree Source for the Renesas RZ/N1 SoC Family of devices
> + *
> + * Copyright (C) 2018 Renesas Electronics Europe Limited
> + *
> + */
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> +/ {
> + compatible = "renesas,rzn1";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu@0 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a7";
> + reg = <0>;
> + };
> + cpu@1 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a7";
> + reg = <1>;
> + };
> + };
I see you don't like empy lines, that's fine, it is not a strict
requiremen afaik, but I find a few empty lines here and there more
redable, expecially if the file is going to grow, as it will be.
> + clocks {
> + /*
> + * this is fixed clock for now,
> + * until the clock driver is merged
> + */
> + clkuarts: clkuarts {
You can remove the node lable if it's the same as the node name afaik
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <47619047>;
> + };
> + };
Grouping clock nodes under a "clocks" one is now deprecated.
Please see, ie.
"ARM: dts: r7s72100: stop grouping clocks under a "clocks" subnode"
Thanks
j
> + arch-timer {
> + compatible = "arm,cortex-a7-timer",
> + "arm,armv7-timer";
> + interrupt-parent = <&gic>;
> + arm,cpu-registers-not-fw-configured;
> + interrupts =
> + <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
> + IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) |
> + IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) |
> + IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) |
> + IRQ_TYPE_LEVEL_LOW)>;
> + };
> + soc {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + interrupt-parent = <&gic>;
> + ranges;
> +
> + gic: gic@44101000 {
> + compatible = "arm,cortex-a7-gic", "arm,gic-400";
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + reg = <0x44101000 0x1000>, /* Distributer */
> + <0x44102000 0x2000>, /* CPU interface */
> + <0x44104000 0x2000>, /* Virt interface control */
> + <0x44106000 0x2000>; /* Virt CPU interface */
> + interrupts =
> + <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) |
> + IRQ_TYPE_LEVEL_HIGH)>;
> + };
> + sysctrl: sysctrl@4000c000 {
> + compatible = "renesas,rzn1-sysctrl", "syscon",
> + "simple-mfd";
> + reg = <0x4000c000 0x1000>;
> +
> + reboot {
> + compatible = "renesas,rzn1-reboot";
> + };
> + };
> + uart0: serial@40060000 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x40060000 0x400>;
> + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&clkuarts>;
> + clock-names = "baudclk";
> + status = "disabled";
> + };
> + };
> +};
> --
> 2.7.4
>
signature.asc
Description: PGP signature
