Hello Brendan,
[ ... ]
> +static bool aspeed_i2c_master_irq(struct aspeed_i2c_bus *bus)
> +{
> + u32 irq_status, status_ack = 0, command = 0;
> + struct i2c_msg *msg;
> + u8 recv_byte;
> +
> + spin_lock(&bus->lock);
> + irq_status = readl(bus->base + ASPEED_I2C_INTR_STS_REG);
> +
> + if (irq_status & ASPEED_I2CD_INTR_BUS_RECOVER_DONE) {
> + bus->master_state = ASPEED_I2C_MASTER_INACTIVE;
> + status_ack |= ASPEED_I2CD_INTR_BUS_RECOVER_DONE;
> + goto out_complete;
> + }
> +
> + /*
> + * Either we encountered an interrupt that reports an error, or we are
> + * in an invalid state.
> + */
> + if (irq_status & ASPEED_I2CD_INTR_ERROR ||
> + (!bus->msgs && bus->master_state != ASPEED_I2C_MASTER_STOP)) {
> + dev_dbg(bus->dev, "received error interrupt: 0x%08x",
> + irq_status);
> + bus->cmd_err = -EIO;
> + __aspeed_i2c_do_stop(bus);
If I am correct, this will continuously send STOP commands if
an interrupt error is reported. It might be worth checking for
this potential issue.
Thanks,
C.
> + goto out_no_complete;
> + }
> + msg = &bus->msgs[bus->msgs_index];
> +
> + /*
> + * START is a special case because we still have to handle a subsequent
> + * TX or RX immediately after we handle it, so we handle it here and
> + * then update the state and handle the new state below.
> + */
> + if (bus->master_state == ASPEED_I2C_MASTER_START) {
> + if (unlikely(!(irq_status & ASPEED_I2CD_INTR_TX_ACK))) {
> + dev_dbg(bus->dev,
> + "no slave present at %02x", msg->addr);
> + status_ack |= ASPEED_I2CD_INTR_TX_NAK;
> + goto error_and_stop;
> + }
> + status_ack |= ASPEED_I2CD_INTR_TX_ACK;
> + if (msg->flags & I2C_M_RD)
> + bus->master_state = ASPEED_I2C_MASTER_RX_FIRST;
> + else
> + bus->master_state = ASPEED_I2C_MASTER_TX_FIRST;
> + }
> +
> + switch (bus->master_state) {
> + case ASPEED_I2C_MASTER_TX:
> + if (unlikely(irq_status & ASPEED_I2CD_INTR_TX_NAK)) {
> + dev_dbg(bus->dev, "slave NACKed TX");
> + status_ack |= ASPEED_I2CD_INTR_TX_NAK;
> + goto error_and_stop;
> + } else if (unlikely(!(irq_status & ASPEED_I2CD_INTR_TX_ACK))) {
> + dev_err(bus->dev, "slave failed to ACK TX");
> + goto error_and_stop;
> + }
> + status_ack |= ASPEED_I2CD_INTR_TX_ACK;
> + /* fallthrough intended */
> + case ASPEED_I2C_MASTER_TX_FIRST:
> + if (bus->buf_index < msg->len) {
> + bus->master_state = ASPEED_I2C_MASTER_TX;
> + writel(msg->buf[bus->buf_index++],
> + bus->base + ASPEED_I2C_BYTE_BUF_REG);
> + writel(ASPEED_I2CD_M_TX_CMD,
> + bus->base + ASPEED_I2C_CMD_REG);
> + } else {
> + __aspeed_i2c_next_msg_or_stop(bus);
> + }
> + goto out_no_complete;
> + case ASPEED_I2C_MASTER_RX_FIRST:
> + /* RX may not have completed yet (only address cycle) */
> + if (!(irq_status & ASPEED_I2CD_INTR_RX_DONE))
> + goto out_no_complete;
> + /* fallthrough intended */
> + case ASPEED_I2C_MASTER_RX:
> + if (unlikely(!(irq_status & ASPEED_I2CD_INTR_RX_DONE))) {
> + dev_err(bus->dev, "master failed to RX");
> + goto error_and_stop;
> + }
> + status_ack |= ASPEED_I2CD_INTR_RX_DONE;
> +
> + recv_byte = readl(bus->base + ASPEED_I2C_BYTE_BUF_REG) >> 8;
> + msg->buf[bus->buf_index++] = recv_byte;
> +
> + if (msg->flags & I2C_M_RECV_LEN) {
> + if (unlikely(recv_byte > I2C_SMBUS_BLOCK_MAX)) {
> + bus->cmd_err = -EPROTO;
> + __aspeed_i2c_do_stop(bus);
> + goto out_no_complete;
> + }
> + msg->len = recv_byte +
> + ((msg->flags & I2C_CLIENT_PEC) ? 2 : 1);
> + msg->flags &= ~I2C_M_RECV_LEN;
> + }
> +
> + if (bus->buf_index < msg->len) {
> + bus->master_state = ASPEED_I2C_MASTER_RX;
> + command = ASPEED_I2CD_M_RX_CMD;
> + if (bus->buf_index + 1 == msg->len)
> + command |= ASPEED_I2CD_M_S_RX_CMD_LAST;
> + writel(command, bus->base + ASPEED_I2C_CMD_REG);
> + } else {
> + __aspeed_i2c_next_msg_or_stop(bus);
> + }
> + goto out_no_complete;
> + case ASPEED_I2C_MASTER_STOP:
> + if (unlikely(!(irq_status & ASPEED_I2CD_INTR_NORMAL_STOP))) {
> + dev_err(bus->dev, "master failed to STOP");
> + bus->cmd_err = -EIO;
> + /* Do not STOP as we have already tried. */
> + } else {
> + status_ack |= ASPEED_I2CD_INTR_NORMAL_STOP;
> + }
> +
> + bus->master_state = ASPEED_I2C_MASTER_INACTIVE;
> + goto out_complete;
> + case ASPEED_I2C_MASTER_INACTIVE:
> + dev_err(bus->dev,
> + "master received interrupt 0x%08x, but is inactive",
> + irq_status);
> + bus->cmd_err = -EIO;
> + /* Do not STOP as we should be inactive. */
> + goto out_complete;
> + default:
> + WARN(1, "unknown master state\n");
> + bus->master_state = ASPEED_I2C_MASTER_INACTIVE;
> + bus->cmd_err = -EIO;
> + goto out_complete;
> + }
> +error_and_stop:
> + bus->cmd_err = -EIO;
> + __aspeed_i2c_do_stop(bus);
> + goto out_no_complete;
> +out_complete:
> + complete(&bus->cmd_complete);
> +out_no_complete:
> + if (irq_status != status_ack)
> + dev_err(bus->dev,
> + "irq handled != irq. expected 0x%08x, but was 0x%08x\n",
> + irq_status, status_ack);
> + writel(irq_status, bus->base + ASPEED_I2C_INTR_STS_REG);
> + spin_unlock(&bus->lock);
> + return !!irq_status;
> +}
> +
> +static irqreturn_t aspeed_i2c_bus_irq(int irq, void *dev_id)
> +{
> + struct aspeed_i2c_bus *bus = dev_id;
> +
> + if (aspeed_i2c_master_irq(bus))
> + return IRQ_HANDLED;
> + else
> + return IRQ_NONE;
> +}
> +
> +static int aspeed_i2c_master_xfer(struct i2c_adapter *adap,
> + struct i2c_msg *msgs, int num)
> +{
> + struct aspeed_i2c_bus *bus = adap->algo_data;
> + unsigned long time_left, flags;
> + int ret = 0;
> +
> + spin_lock_irqsave(&bus->lock, flags);
> + bus->cmd_err = 0;
> +
> + /* If bus is busy, attempt recovery. We assume a single master
> + * environment.
> + */
> + if (readl(bus->base + ASPEED_I2C_CMD_REG) & ASPEED_I2CD_BUS_BUSY_STS) {
> + spin_unlock_irqrestore(&bus->lock, flags);
> + ret = aspeed_i2c_recover_bus(bus);
> + if (ret)
> + return ret;
> + spin_lock_irqsave(&bus->lock, flags);
> + }
> +
> + bus->msgs = msgs;
> + bus->msgs_index = 0;
> + bus->msgs_count = num;
> +
> + reinit_completion(&bus->cmd_complete);
> + __aspeed_i2c_do_start(bus);
> + spin_unlock_irqrestore(&bus->lock, flags);
> +
> + time_left = wait_for_completion_timeout(&bus->cmd_complete,
> + bus->adap.timeout);
> +
> + spin_lock_irqsave(&bus->lock, flags);
> + bus->msgs = NULL;
> + if (time_left == 0)
> + ret = -ETIMEDOUT;
> + else
> + ret = bus->cmd_err;
> + spin_unlock_irqrestore(&bus->lock, flags);
> +
> + /* If nothing went wrong, return number of messages transferred. */
> + if (ret >= 0)
> + return bus->msgs_index + 1;
> + else
> + return ret;
> +}
> +
> +static u32 aspeed_i2c_functionality(struct i2c_adapter *adap)
> +{
> + return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | I2C_FUNC_SMBUS_BLOCK_DATA;
> +}
> +
> +static const struct i2c_algorithm aspeed_i2c_algo = {
> + .master_xfer = aspeed_i2c_master_xfer,
> + .functionality = aspeed_i2c_functionality,
> +};
> +
> +static u32 aspeed_i2c_get_clk_reg_val(u32 divisor)
> +{
> + u32 base_clk, clk_high, clk_low, tmp;
> +
> + /*
> + * The actual clock frequency of SCL is:
> + * SCL_freq = APB_freq / (base_freq * (SCL_high + SCL_low))
> + * = APB_freq / divisor
> + * where base_freq is a programmable clock divider; its value is
> + * base_freq = 1 << base_clk
> + * SCL_high is the number of base_freq clock cycles that SCL stays high
> + * and SCL_low is the number of base_freq clock cycles that SCL stays
> + * low for a period of SCL.
> + * The actual register has a minimum SCL_high and SCL_low minimum of 1;
> + * thus, they start counting at zero. So
> + * SCL_high = clk_high + 1
> + * SCL_low = clk_low + 1
> + * Thus,
> + * SCL_freq = APB_freq /
> + * ((1 << base_clk) * (clk_high + 1 + clk_low + 1))
> + * The documentation recommends clk_high >= 8 and clk_low >= 7 when
> + * possible; this last constraint gives us the following solution:
> + */
> + base_clk = divisor > 33 ? ilog2((divisor - 1) / 32) + 1 : 0;
> + tmp = divisor / (1 << base_clk);
> + clk_high = tmp / 2 + tmp % 2;
> + clk_low = tmp - clk_high;
> +
> + clk_high -= 1;
> + clk_low -= 1;
> +
> + return ((clk_high << ASPEED_I2CD_TIME_SCL_HIGH_SHIFT)
> + & ASPEED_I2CD_TIME_SCL_HIGH_MASK)
> + | ((clk_low << ASPEED_I2CD_TIME_SCL_LOW_SHIFT)
> + & ASPEED_I2CD_TIME_SCL_LOW_MASK)
> + | (base_clk & ASPEED_I2CD_TIME_BASE_DIVISOR_MASK);
> +}
> +
> +static int __aspeed_i2c_init_clk(struct aspeed_i2c_bus *bus,
> + struct platform_device *pdev)
> +{
> + u32 clk_freq, divisor, clk_reg_val;
> + struct clk *pclk;
> + int ret;
> +
> + pclk = devm_clk_get(&pdev->dev, NULL);
> + if (IS_ERR(pclk)) {
> + dev_err(&pdev->dev, "clk_get failed\n");
> + return PTR_ERR(pclk);
> + }
> + ret = of_property_read_u32(pdev->dev.of_node,
> + "bus-frequency", &clk_freq);
> + if (ret < 0) {
> + dev_err(&pdev->dev,
> + "Could not read bus-frequency property\n");
> + clk_freq = 100000;
> + }
> + divisor = clk_get_rate(pclk) / clk_freq;
> + /* We just need the clock rate, we don't actually use the clk object. */
> + devm_clk_put(&pdev->dev, pclk);
> +
> + clk_reg_val = aspeed_i2c_get_clk_reg_val(divisor);
> + writel(clk_reg_val, bus->base + ASPEED_I2C_AC_TIMING_REG1);
> +
> + /*
> + * If the base divisor is non-zero then we do not want to enable high
> + * speed mode, otherwise we might as well enable it.
> + * For reference, setting high speed mode will make the base divisor
> + * zero and corresponds to a minimum SCL frequency of about 1.5MHz.
> + */
> + if (clk_reg_val & ASPEED_I2CD_TIME_BASE_DIVISOR_MASK) {
> + writel(ASPEED_NO_TIMEOUT_CTRL,
> + bus->base + ASPEED_I2C_AC_TIMING_REG2);
> + } else {
> + writel(readl(bus->base + ASPEED_I2C_FUN_CTRL_REG) |
> + ASPEED_I2CD_M_HIGH_SPEED_EN |
> + ASPEED_I2CD_M_SDA_DRIVE_1T_EN |
> + ASPEED_I2CD_SDA_DRIVE_1T_EN,
> + bus->base + ASPEED_I2C_FUN_CTRL_REG);
> +
> + writel(0x3, bus->base + ASPEED_I2C_AC_TIMING_REG2);
> + }
> +
> + return 0;
> +}
> +
> +static int __aspeed_i2c_init(struct aspeed_i2c_bus *bus,
> + struct platform_device *pdev)
> +{
> + int ret;
> +
> + /* Disable everything. */
> + writel(0, bus->base + ASPEED_I2C_FUN_CTRL_REG);
> +
> + ret = __aspeed_i2c_init_clk(bus, pdev);
> + if (ret < 0)
> + return ret;
> +
> + /* Enable Master Mode */
> + writel(readl(bus->base + ASPEED_I2C_FUN_CTRL_REG) |
> + ASPEED_I2CD_MASTER_EN |
> + /* TODO: provide device tree option for multi-master mode. */
> + ASPEED_I2CD_MULTI_MASTER_DIS,
> + bus->base + ASPEED_I2C_FUN_CTRL_REG);
> +
> + /* Set interrupt generation of I2C controller */
> + writel(ASPEED_I2CD_INTR_ALL, bus->base + ASPEED_I2C_INTR_CTRL_REG);
> +
> + return 0;
> +}
> +
> +static int aspeed_i2c_reset(struct aspeed_i2c_bus *bus)
> +{
> + struct platform_device *pdev = to_platform_device(bus->dev);
> + unsigned long flags;
> + int ret;
> +
> + spin_lock_irqsave(&bus->lock, flags);
> +
> + /* Disable and quiesce interrupts. */
> + reinit_completion(&bus->cmd_complete);
> + writel(0, bus->base + ASPEED_I2C_INTR_CTRL_REG);
> +
> + spin_unlock_irqrestore(&bus->lock, flags);
> + /*
> + * We need to make sure that there are no interrupts that fired just
> + * before we grabbed the lock; if that did not happen, then we are going
> + * to timeout and that is okay.
> + */
> + wait_for_completion_timeout(&bus->cmd_complete, bus->adap.timeout);
> + spin_lock_irqsave(&bus->lock, flags);
> +
> + ret = __aspeed_i2c_init(bus, pdev);
> +
> + spin_unlock_irqrestore(&bus->lock, flags);
> +
> + return ret;
> +}
> +
> +static int aspeed_i2c_probe_bus(struct platform_device *pdev)
> +{
> + struct aspeed_i2c_bus *bus;
> + struct resource *res;
> + int ret;
> +
> + bus = devm_kzalloc(&pdev->dev, sizeof(*bus), GFP_KERNEL);
> + if (!bus)
> + return -ENOMEM;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + bus->base = devm_ioremap_resource(&pdev->dev, res);
> + if (IS_ERR(bus->base))
> + return PTR_ERR(bus->base);
> +
> + /* Initialize the I2C adapter */
> + spin_lock_init(&bus->lock);
> + init_completion(&bus->cmd_complete);
> + bus->adap.owner = THIS_MODULE;
> + bus->adap.retries = 0;
> + bus->adap.timeout = 5 * HZ;
> + bus->adap.algo = &aspeed_i2c_algo;
> + bus->adap.algo_data = bus;
> + bus->adap.dev.parent = &pdev->dev;
> + bus->adap.dev.of_node = pdev->dev.of_node;
> + snprintf(bus->adap.name, sizeof(bus->adap.name), "Aspeed i2c");
> +
> + bus->dev = &pdev->dev;
> +
> + /*
> + * No need to quiesce interrupts because there is no interrupt handler
> + * installed.
> + */
> + writel(0, bus->base + ASPEED_I2C_INTR_CTRL_REG);
> + ret = __aspeed_i2c_init(bus, pdev);
> + if (ret < 0)
> + return ret;
> +
> + bus->irq = irq_of_parse_and_map(pdev->dev.of_node, 0);
> + ret = devm_request_irq(&pdev->dev, bus->irq, aspeed_i2c_bus_irq,
> + 0, dev_name(&pdev->dev), bus);
> + if (ret < 0)
> + return ret;
> +
> + ret = i2c_add_adapter(&bus->adap);
> + if (ret < 0)
> + return ret;
> +
> + platform_set_drvdata(pdev, bus);
> +
> + dev_info(bus->dev, "i2c bus %d registered, irq %d\n",
> + bus->adap.nr, bus->irq);
> +
> + return 0;
> +}
> +
> +static int aspeed_i2c_remove_bus(struct platform_device *pdev)
> +{
> + struct aspeed_i2c_bus *bus = platform_get_drvdata(pdev);
> + unsigned long flags;
> +
> + spin_lock_irqsave(&bus->lock, flags);
> +
> + /* Disable everything. */
> + writel(0, bus->base + ASPEED_I2C_FUN_CTRL_REG);
> + writel(0, bus->base + ASPEED_I2C_INTR_CTRL_REG);
> +
> + spin_unlock_irqrestore(&bus->lock, flags);
> +
> + i2c_del_adapter(&bus->adap);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id aspeed_i2c_bus_of_table[] = {
> + { .compatible = "aspeed,ast2400-i2c-bus", },
> + { .compatible = "aspeed,ast2500-i2c-bus", },
> + { },
> +};
> +MODULE_DEVICE_TABLE(of, aspeed_i2c_bus_of_table);
> +
> +static struct platform_driver aspeed_i2c_bus_driver = {
> + .probe = aspeed_i2c_probe_bus,
> + .remove = aspeed_i2c_remove_bus,
> + .driver = {
> + .name = "aspeed-i2c-bus",
> + .of_match_table = aspeed_i2c_bus_of_table,
> + },
> +};
> +module_platform_driver(aspeed_i2c_bus_driver);
> +
> +MODULE_AUTHOR("Brendan Higgins <brendanhigg...@google.com>");
> +MODULE_DESCRIPTION("Aspeed I2C Bus Driver");
> +MODULE_LICENSE("GPL v2");
>
