On Wed, Jan 18, 2017 at 01:58:28PM +0200, Mathias Nyman wrote: > On 12.01.2017 10:38, Roger Quadros wrote: > > Mathias, > > > > On 11/01/17 17:08, Alan Stern wrote: > > > On Wed, 11 Jan 2017, Mathias Nyman wrote: > > > > > > > On 17.11.2016 13:43, Sriram Dash wrote: > > > > > From: Arnd Bergmann <a...@arndb.de> > > > > > > > > > > For xhci-hcd platform device, all the DMA parameters are not > > > > > configured properly, notably dma ops for dwc3 devices. So, set > > > > > the dma for xhci from sysdev. sysdev is pointing to device that > > > > > is known to the system firmware or hardware. > > > > > > > > > > Signed-off-by: Arnd Bergmann <a...@arndb.de> > > > > > Signed-off-by: Sriram Dash <sriram.d...@nxp.com> > > > > > Tested-by: Baolin Wang <baolin.w...@linaro.org> > > > > > --- > > > > > > > > ... > > > > > > > > > + /* > > > > > + * sysdev must point to a device that is known to the system > > > > > firmware > > > > > + * or PCI hardware. We handle these three cases here: > > > > > + * 1. xhci_plat comes from firmware > > > > > + * 2. xhci_plat is child of a device from firmware (dwc3-plat) > > > > > + * 3. xhci_plat is grandchild of a pci device (dwc3-pci) > > > > > + */ > > > > > + sysdev = &pdev->dev; > > > > > + if (sysdev->parent && !sysdev->of_node && > > > > > sysdev->parent->of_node) > > > > > + sysdev = sysdev->parent; > > > > > +#ifdef CONFIG_PCI > > > > > + else if (sysdev->parent && sysdev->parent->parent && > > > > > + sysdev->parent->parent->bus == &pci_bus_type) > > > > > + sysdev = sysdev->parent->parent; > > > > > +#endif > > > > > + > > > > > > > > Not maybe the the ideal situation here, and looks really tailored to > > > > make PCI dwc3 > > > > controllers with xhci support work. > > > > > > > > Was there some reason child devices can't automatically inherit the dma > > > > mask from the parents, > > > > forcing us to dig it from grandparents? > > > > > > > > Anyway, looks like the dwc3 part is already in 4.10-rc, > > > > If Greg and Alan want to take this series that's fine by me > > > > > > I have no objections. > > > > > > Alan Stern > > > > > > > I haven't tested that it won't break anything on PCI XHCI controllers > > > > though > > > > > > > > -Mathias > > > > Are you going to pick all the remaining patches from this series (i.e. 1 to > > 4)? > > > > That should fix the warning that people are seeing on v4.10-rc. > > > > Let's check with Greg > > Greg, 5/6 and 6/6 are in 4.10-rc already, causing additional warnings for > people using dwc3 xhci. > > First 3 patches change usb core, patch 4 xhci. > > Compiles and boots, doesn't break pci xhci (non-dwc3) functionality > > Would you like me to send first 4 patches for usb-linus to get a clean final > 4.10 > without warnings, or to send them for usb-next? > > Or will you just pick the patches from here directly.
I don't have them "here" anymore, they are long-gone from my patch queue, sorry. Can you resend them, I don't know what these patches contained, but if they fix an 4.10 issue, that would be good to have there, right? thanks, greg k-h
