From: Sudip Mukherjee <sudip.mukher...@codethink.co.uk>
Add the serial driver for the Exar chips. And also register the
platform device for the GPIO provided by the Exar chips.
Signed-off-by: Sudip Mukherjee <sudip.mukher...@codethink.co.uk>
---
Andy,
I hope the grouping and ordering of the header files are ok this time.
One comment has been changed to Kerneldoc description, but as I have never
made a kerneldoc description before so not sure if it is correct.
I have already replied in a separate mail about the problem if we
register gpio before.
drivers/tty/serial/8250/8250_exar.c | 433 ++++++++++++++++++++++++++++++++++++
drivers/tty/serial/8250/Kconfig | 4 +
drivers/tty/serial/8250/Makefile | 1 +
3 files changed, 438 insertions(+)
create mode 100644 drivers/tty/serial/8250/8250_exar.c
diff --git a/drivers/tty/serial/8250/8250_exar.c
b/drivers/tty/serial/8250/8250_exar.c
new file mode 100644
index 0000000..9eb6ded
--- /dev/null
+++ b/drivers/tty/serial/8250/8250_exar.c
@@ -0,0 +1,433 @@
+/*
+ * Probe module for 8250/16550-type Exar chips PCI serial ports.
+ *
+ * Based on drivers/tty/serial/8250/8250_pci.c,
+ *
+ * Copyright (C) 2017 Sudip Mukherjee, All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License.
+ */
+
+#undef DEBUG
+
+#include <linux/bitops.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/serial_core.h>
+#include <linux/serial_reg.h>
+#include <linux/slab.h>
+#include <linux/string.h>
+#include <linux/tty.h>
+#include <linux/8250_pci.h>
+
+#include <asm/byteorder.h>
+
+#include "8250.h"
+
+#define PCI_DEVICE_ID_COMMTECH_4224PCIE 0x0020
+#define PCI_DEVICE_ID_COMMTECH_4228PCIE 0x0021
+#define PCI_DEVICE_ID_COMMTECH_4222PCIE 0x0022
+#define PCI_DEVICE_ID_EXAR_XR17V4358 0x4358
+#define PCI_DEVICE_ID_EXAR_XR17V8358 0x8358
+
+#define UART_EXAR_MPIOINT_7_0 0x8f /* MPIOINT[7:0] */
+#define UART_EXAR_MPIOLVL_7_0 0x90 /* MPIOLVL[7:0] */
+#define UART_EXAR_MPIO3T_7_0 0x91 /* MPIO3T[7:0] */
+#define UART_EXAR_MPIOINV_7_0 0x92 /* MPIOINV[7:0] */
+#define UART_EXAR_MPIOSEL_7_0 0x93 /* MPIOSEL[7:0] */
+#define UART_EXAR_MPIOOD_7_0 0x94 /* MPIOOD[7:0] */
+#define UART_EXAR_MPIOINT_15_8 0x95 /* MPIOINT[15:8] */
+#define UART_EXAR_MPIOLVL_15_8 0x96 /* MPIOLVL[15:8] */
+#define UART_EXAR_MPIO3T_15_8 0x97 /* MPIO3T[15:8] */
+#define UART_EXAR_MPIOINV_15_8 0x98 /* MPIOINV[15:8] */
+#define UART_EXAR_MPIOSEL_15_8 0x99 /* MPIOSEL[15:8] */
+#define UART_EXAR_MPIOOD_15_8 0x9a /* MPIOOD[15:8] */
+
+struct exar8250;
+
+/**
+ * @uart_offset the space between channels
+ *
+ * @reg_shift describes how the UART registers are mapped to PCI memory
+ * by the card.
+ */
+
+struct exar8250_board {
+ unsigned int num_ports;
+ unsigned int base_baud;
+ unsigned int uart_offset;
+ unsigned int reg_shift;
+ bool has_slave;
+ int (*setup)(struct exar8250 *, struct pci_dev *,
+ const struct exar8250_board *,
+ struct uart_8250_port *, int);
+ void (*exit)(struct pci_dev *pcidev);
+};
+
+struct exar8250 {
+ unsigned int nr;
+ struct exar8250_board *board;
+ int line[0];
+};
+
+static int default_setup(struct exar8250 *priv, struct pci_dev *pcidev,
+ const struct exar8250_board *board,
+ struct uart_8250_port *port, int idx)
+{
+ unsigned int offset, bar = 0;
+
+ if (board->uart_offset)
+ offset = idx * board->uart_offset;
+ else
+ offset = idx * 0x200;
+
+ port->port.iotype = UPIO_MEM;
+ port->port.iobase = 0;
+ port->port.mapbase = pci_resource_start(pcidev, bar) + offset;
+ port->port.membase = pcim_iomap_table(pcidev)[bar] + offset;
+ port->port.regshift = board->reg_shift;
+
+ return 0;
+}
+
+static int
+pci_xr17c154_setup(struct exar8250 *priv, struct pci_dev *pcidev,
+ const struct exar8250_board *board,
+ struct uart_8250_port *port, int idx)
+{
+ port->port.flags |= UPF_EXAR_EFR;
+ return default_setup(priv, pcidev, board, port, idx);
+}
+
+static void setup_gpio(u8 __iomem *p)
+{
+ writeb(0x00, p + UART_EXAR_MPIOINT_7_0);
+ writeb(0x00, p + UART_EXAR_MPIOLVL_7_0);
+ writeb(0x00, p + UART_EXAR_MPIO3T_7_0);
+ writeb(0x00, p + UART_EXAR_MPIOINV_7_0);
+ writeb(0x00, p + UART_EXAR_MPIOSEL_7_0);
+ writeb(0x00, p + UART_EXAR_MPIOOD_7_0);
+ writeb(0x00, p + UART_EXAR_MPIOINT_15_8);
+ writeb(0x00, p + UART_EXAR_MPIOLVL_15_8);
+ writeb(0x00, p + UART_EXAR_MPIO3T_15_8);
+ writeb(0x00, p + UART_EXAR_MPIOINV_15_8);
+ writeb(0x00, p + UART_EXAR_MPIOSEL_15_8);
+ writeb(0x00, p + UART_EXAR_MPIOOD_15_8);
+}
+
+static void *
+xr17v35x_register_gpio(struct pci_dev *pcidev)
+{
+ struct platform_device *pdev;
+
+ pdev = platform_device_alloc("gpio_exar", PLATFORM_DEVID_AUTO);
+ if (!pdev)
+ return NULL;
+
+ platform_set_drvdata(pdev, pcidev);
+ if (platform_device_add(pdev) < 0) {
+ platform_device_put(pdev);
+ return NULL;
+ }
+
+ return pdev;
+}
+
+static int
+pci_xr17v35x_setup(struct exar8250 *priv, struct pci_dev *pcidev,
+ const struct exar8250_board *board,
+ struct uart_8250_port *port, int idx)
+{
+ u8 __iomem *p;
+ int ret;
+
+ p = pci_ioremap_bar(pcidev, 0);
+ if (!p)
+ return -ENOMEM;
+
+ port->port.flags |= UPF_EXAR_EFR;
+
+ /*
+ * Setup the uart clock for the devices on expansion slot to
+ * half the clock speed of the main chip (which is 125MHz)
+ */
+ if (board->has_slave && idx >= 8)
+ port->port.uartclk = (7812500 * 16 / 2);
+
+ /* Setup Multipurpose Input/Output pins. */
+ if (idx == 0)
+ setup_gpio(p);
+
+ writeb(0x00, p + UART_EXAR_8XMODE);
+ writeb(UART_FCTR_EXAR_TRGD, p + UART_EXAR_FCTR);
+ writeb(128, p + UART_EXAR_TXTRG);
+ writeb(128, p + UART_EXAR_RXTRG);
+ iounmap(p);
+
+ ret = default_setup(priv, pcidev, board, port, idx);
+ if (ret)
+ return ret;
+
+ if (idx == 0)
+ port->port.private_data =
+ xr17v35x_register_gpio(pcidev);
+
+ return 0;
+}
+
+static void pci_xr17v35x_exit(struct pci_dev *pcidev)
+{
+ struct exar8250 *priv = pci_get_drvdata(pcidev);
+ struct uart_8250_port *port = serial8250_get_port(priv->line[0]);
+ struct platform_device *pdev = port->port.private_data;
+
+ if (!pdev)
+ return;
+
+ platform_device_unregister(pdev);
+ port->port.private_data = NULL;
+}
+
+static int
+exar_pci_probe(struct pci_dev *pcidev, const struct pci_device_id *ent)
+{
+ unsigned int nr_ports, i, bar = 0, maxnr;
+ struct exar8250_board *board;
+ struct uart_8250_port uart;
+ struct exar8250 *priv;
+ int rc;
+
+ rc = pcim_enable_device(pcidev);
+ if (rc)
+ return rc;
+
+ board = (struct exar8250_board *)ent->driver_data;
+ if (!board) {
+ board = devm_kzalloc(&pcidev->dev, sizeof(*board),
+ GFP_KERNEL);
+ board->base_baud = 1843200;
+ }
+
+ maxnr = pci_resource_len(pcidev, bar) >>
+ (board->reg_shift + 3);
+
+ nr_ports = board->num_ports ? board->num_ports :
+ pcidev->device & 0x0f;
+
+ priv = devm_kzalloc(&pcidev->dev, sizeof(*priv) +
+ sizeof(unsigned int) * nr_ports,
+ GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->board = board;
+
+ memset(&uart, 0, sizeof(uart));
+ uart.port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ;
+ uart.port.uartclk = board->base_baud * 16;
+ uart.port.irq = pcidev->irq;
+ uart.port.dev = &pcidev->dev;
+
+ for (i = 0; i < nr_ports && i < maxnr; i++) {
+ if (board->setup)
+ rc = board->setup(priv, pcidev, board, &uart, i);
+ else
+ rc = pci_xr17c154_setup(priv, pcidev, board, &uart, i);
+
+ if (rc) {
+ dev_err(&pcidev->dev,
+ "Failed to setup port %u\n", i);
+ break;
+ }
+
+ dev_dbg(&pcidev->dev, "Setup PCI port: port %lx, irq %d, type
%d\n",
+ uart.port.iobase, uart.port.irq, uart.port.iotype);
+
+ priv->line[i] = serial8250_register_8250_port(&uart);
+ if (priv->line[i] < 0) {
+ dev_err(&pcidev->dev,
+ "Couldn't register serial port %lx, irq %d,
type %d, error %d\n",
+ uart.port.iobase, uart.port.irq,
+ uart.port.iotype, priv->line[i]);
+ break;
+ }
+ }
+ priv->nr = i;
+ pci_set_drvdata(pcidev, priv);
+ return 0;
+}
+
+static void exar_pci_remove(struct pci_dev *pcidev)
+{
+ struct exar8250 *priv = pci_get_drvdata(pcidev);
+ unsigned int i;
+
+ for (i = 0; i < priv->nr; i++)
+ serial8250_unregister_port(priv->line[i]);
+
+ if (priv->board->exit)
+ priv->board->exit(pcidev);
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int exar_suspend(struct device *dev)
+{
+ struct pci_dev *pcidev = to_pci_dev(dev);
+ struct exar8250 *priv = pci_get_drvdata(pcidev);
+ unsigned int i;
+
+ for (i = 0; i < priv->nr; i++)
+ if (priv->line[i] >= 0)
+ serial8250_suspend_port(priv->line[i]);
+
+ /* Ensure that every init quirk is properly torn down */
+
+ if (priv->board->exit)
+ priv->board->exit(pcidev);
+
+ return 0;
+}
+
+static int exar_resume(struct device *dev)
+{
+ struct pci_dev *pcidev = to_pci_dev(dev);
+ struct exar8250 *priv = pci_get_drvdata(pcidev);
+ unsigned int i;
+
+ for (i = 0; i < priv->nr; i++)
+ if (priv->line[i] >= 0)
+ serial8250_resume_port(priv->line[i]);
+
+ return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(exar_pci_pm, exar_suspend, exar_resume);
+
+static const struct exar8250_board pbn_exar_ibm_saturn = {
+ .num_ports = 1,
+ .base_baud = 921600,
+};
+
+static const struct exar8250_board pbn_exar_XR17C152 = {
+ .base_baud = 921600,
+};
+
+static const struct exar8250_board pbn_exar_XR17C154 = {
+ .base_baud = 921600,
+};
+
+static const struct exar8250_board pbn_exar_XR17C158 = {
+ .base_baud = 921600,
+};
+
+static const struct exar8250_board pbn_exar_XR17V352 = {
+ .base_baud = 7812500,
+ .uart_offset = 0x400,
+ .setup = pci_xr17v35x_setup,
+ .exit = pci_xr17v35x_exit,
+};
+
+static const struct exar8250_board pbn_exar_XR17V354 = {
+ .base_baud = 7812500,
+ .uart_offset = 0x400,
+ .setup = pci_xr17v35x_setup,
+ .exit = pci_xr17v35x_exit,
+};
+
+static const struct exar8250_board pbn_exar_XR17V358 = {
+ .base_baud = 7812500,
+ .uart_offset = 0x400,
+ .setup = pci_xr17v35x_setup,
+ .exit = pci_xr17v35x_exit,
+};
+
+static const struct exar8250_board pbn_exar_XR17V4358 = {
+ .num_ports = 12,
+ .base_baud = 7812500,
+ .uart_offset = 0x400,
+ .has_slave = true,
+ .setup = pci_xr17v35x_setup,
+ .exit = pci_xr17v35x_exit,
+};
+
+static const struct exar8250_board pbn_exar_XR17V8358 = {
+ .num_ports = 16,
+ .base_baud = 7812500,
+ .uart_offset = 0x400,
+ .has_slave = true,
+ .setup = pci_xr17v35x_setup,
+ .exit = pci_xr17v35x_exit,
+};
+
+#define CONNECT_DEVICE(devid, sdevid) {\
+ PCI_DEVICE_SUB(\
+ PCI_VENDOR_ID_EXAR,\
+ PCI_DEVICE_ID_EXAR_##devid,\
+ PCI_SUBVENDOR_ID_CONNECT_TECH,\
+ PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_##sdevid)\
+ }
+
+#define EXAR_DEVICE(vend, devid, bd) {\
+ PCI_VDEVICE(\
+ vend, PCI_DEVICE_ID_##devid), (kernel_ulong_t)&bd \
+ }
+
+static struct pci_device_id exar_pci_tbl[] = {
+ CONNECT_DEVICE(XR17C152, UART_2_232),
+ CONNECT_DEVICE(XR17C154, UART_4_232),
+ CONNECT_DEVICE(XR17C158, UART_8_232),
+ CONNECT_DEVICE(XR17C152, UART_1_1),
+ CONNECT_DEVICE(XR17C154, UART_2_2),
+ CONNECT_DEVICE(XR17C158, UART_4_4),
+ CONNECT_DEVICE(XR17C152, UART_2),
+ CONNECT_DEVICE(XR17C154, UART_4),
+ CONNECT_DEVICE(XR17C158, UART_8),
+ CONNECT_DEVICE(XR17C152, UART_2_485),
+ CONNECT_DEVICE(XR17C154, UART_4_485),
+ CONNECT_DEVICE(XR17C158, UART_8_485),
+ {
+ PCI_DEVICE_SUB(PCI_VENDOR_ID_EXAR,
+ PCI_DEVICE_ID_EXAR_XR17C152,
+ PCI_VENDOR_ID_IBM,
+ PCI_SUBDEVICE_ID_IBM_SATURN_SERIAL_ONE_PORT),
+ 0, 0, (kernel_ulong_t)&pbn_exar_ibm_saturn
+ },
+
+ /* Exar Corp. XR17C15[248] Dual/Quad/Octal UART */
+ EXAR_DEVICE(EXAR, EXAR_XR17C152, pbn_exar_XR17C152),
+ EXAR_DEVICE(EXAR, EXAR_XR17C154, pbn_exar_XR17C154),
+ EXAR_DEVICE(EXAR, EXAR_XR17C158, pbn_exar_XR17C158),
+
+ /* Exar Corp. XR17V[48]35[248] Dual/Quad/Octal/Hexa PCIe UARTs */
+ EXAR_DEVICE(EXAR, EXAR_XR17V352, pbn_exar_XR17V352),
+ EXAR_DEVICE(EXAR, EXAR_XR17V354, pbn_exar_XR17V354),
+ EXAR_DEVICE(EXAR, EXAR_XR17V358, pbn_exar_XR17V358),
+ EXAR_DEVICE(EXAR, EXAR_XR17V4358, pbn_exar_XR17V4358),
+ EXAR_DEVICE(EXAR, EXAR_XR17V8358, pbn_exar_XR17V8358),
+ EXAR_DEVICE(COMMTECH, COMMTECH_4222PCIE, pbn_exar_XR17V352),
+ EXAR_DEVICE(COMMTECH, COMMTECH_4224PCIE, pbn_exar_XR17V354),
+ EXAR_DEVICE(COMMTECH, COMMTECH_4228PCIE, pbn_exar_XR17V358),
+ { 0, }
+};
+MODULE_DEVICE_TABLE(pci, exar_pci_tbl);
+
+static struct pci_driver exar_pci_driver = {
+ .name = "exar_serial",
+ .probe = exar_pci_probe,
+ .remove = exar_pci_remove,
+ .driver = {
+ .pm = &exar_pci_pm,
+ },
+ .id_table = exar_pci_tbl,
+};
+module_pci_driver(exar_pci_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Exar Serial Dricer");
+MODULE_AUTHOR("Sudip Mukherjee <sudip.mukher...@codethink.co.uk>");
diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig
index 0b8b674..9e1f7bf 100644
--- a/drivers/tty/serial/8250/Kconfig
+++ b/drivers/tty/serial/8250/Kconfig
@@ -127,6 +127,10 @@ config SERIAL_8250_PCI
Note that serial ports on NetMos 9835 Multi-I/O cards are handled
by the parport_serial driver, enabled with CONFIG_PARPORT_SERIAL.
+config SERIAL_8250_EXAR
+ tristate "8250/16550 PCI device support"
+ depends on SERIAL_8250_PCI
+
config SERIAL_8250_HP300
tristate
depends on SERIAL_8250 && HP300
diff --git a/drivers/tty/serial/8250/Makefile b/drivers/tty/serial/8250/Makefile
index 850e721..2f30f9e 100644
--- a/drivers/tty/serial/8250/Makefile
+++ b/drivers/tty/serial/8250/Makefile
@@ -10,6 +10,7 @@ obj-$(CONFIG_SERIAL_8250) += 8250.o 8250_base.o
8250_base-$(CONFIG_SERIAL_8250_FINTEK) += 8250_fintek.o
obj-$(CONFIG_SERIAL_8250_GSC) += 8250_gsc.o
obj-$(CONFIG_SERIAL_8250_PCI) += 8250_pci.o
+obj-$(CONFIG_SERIAL_8250_EXAR) += 8250_exar.o
obj-$(CONFIG_SERIAL_8250_HP300) += 8250_hp300.o
obj-$(CONFIG_SERIAL_8250_CS) += serial_cs.o
obj-$(CONFIG_SERIAL_8250_ACORN) += 8250_acorn.o
--
1.9.1
