Could someone who knows ide and drive inside and out (Andre?) please
take a look at these figures? Am I forgetting to do something (or doing
something I'm not suposed to) to get the best numbers? I thought I'd be
able to get more than ~4MB/sec off the HPT366 and a UDMA66 drive.

Kernel: 2.4.0-test10-pre6

Onboard PIIX4 (Abit BE6-II):

        [mhaque@viper mhaque]$ sudo hdparm -X34 -d1 -u1 -c3 -m16 /dev/hda

        /dev/hda:
         setting 32-bit I/O support flag to 3
         setting multcount to 16
         setting unmaskirq to 1 (on)
         setting using_dma to 1 (on)
         setting xfermode to 34 (multiword DMA mode2)
         multcount    = 16 (on)
         I/O support  =  3 (32-bit w/sync)
         unmaskirq    =  1 (on)
         using_dma    =  1 (on)

        [mhaque@viper mhaque]$ dmesg|grep '^hda:'; sudo hdparm -Tt /dev/hda
        hda: IBM-DJNA-371350, ATA DISK drive
        hda: 26520480 sectors (13578 MB) w/1966KiB Cache, CHS=1650/255/63,
UDMA(33)

        /dev/hda:
         Timing buffer-cache reads:   128 MB in  1.12 seconds =114.29 MB/sec
         Timing buffered disk reads:  64 MB in  4.94 seconds = 12.96 MB/sec

        [mhaque@viper mhaque]$ sudo hdparm -i /dev/hda

        /dev/hda:

         Model=IBM-DJNA-371350, FwRev=J76OA30K, SerialNo=GM0GMFE4929
         Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
         RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=34
         BuffType=3(DualPortCache), BuffSize=1966kB, MaxMultSect=16,
MultSect=16
         DblWordIO=no, OldPIO=2, DMA=yes, OldDMA=2
         CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=26520480
         tDMA={min:120,rec:120}, DMA modes: mword0 mword1 *mword2 
         IORDY=on/off, tPIO={min:240,w/IORDY:120}, PIO modes: mode3 mode4 
         UDMA modes: mode0 mode1 mode2 mode3 mode4 



Onboard HPT366 (Abit BE6-II):

        [mhaque@viper mhaque]$ sudo hdparm -X66 -d1 -u1 -c3 -m16 /dev/hde

        /dev/hde:
         setting 32-bit I/O support flag to 3
         setting multcount to 16
         setting unmaskirq to 1 (on)
         setting using_dma to 1 (on)
         setting xfermode to 66 (UltraDMA mode2)
         multcount    = 16 (on)
         I/O support  =  3 (32-bit w/sync)
         unmaskirq    =  1 (on)
         using_dma    =  1 (on)

        [mhaque@viper mhaque]$ dmesg|grep '^hde:'; sudo hdparm -Tt /dev/hde
        hde: Maxtor 53073U6, ATA DISK drive
        hde: 60030432 sectors (30736 MB) w/2048KiB Cache, CHS=59554/16/63,
UDMA(66)

        /dev/hde:
         Timing buffer-cache reads:   128 MB in  1.24 seconds =103.23 MB/sec
         Timing buffered disk reads:  64 MB in 16.18 seconds =  3.96 MB/sec

        [mhaque@viper mhaque]$ sudo hdparm -i /dev/hde

        /dev/hde:

         Model=Maxtor 53073U6, FwRev=DA6207V0, SerialNo=K608NRYC
         Config={ Fixed }
         RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
         BuffType=3(DualPortCache), BuffSize=2048kB, MaxMultSect=16,
MultSect=16
         DblWordIO=no, OldPIO=2, DMA=yes, OldDMA=0
         CurCHS=65535/1/63, CurSects=-4128706, LBA=yes, LBAsects=60030432
         tDMA={min:120,rec:120}, DMA modes: mword0 mword1 mword2 
         IORDY=on/off, tPIO={min:120,w/IORDY:120}, PIO modes: mode3 mode4 
         UDMA modes: mode0 mode1 *mode2 mode3 mode4 


-- 

=====================================================================
Mohammad A. Haque                              http://www.haque.net/ 
                                               [EMAIL PROTECTED]

  "Alcohol and calculus don't mix.             Project Lead
   Don't drink and derive." --Unknown          http://wm.themes.org/
                                               [EMAIL PROTECTED]
=====================================================================
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
Please read the FAQ at http://www.tux.org/lkml/

Reply via email to