On Sat, 9 Sep 2000, Alan Cox wrote:
Alan you assume that you only have one disk (this is okay).
How does this wakeup a spindown?
If you call a 'SETMULTI" and the drive is not ready it may/will hang the
system. This is why I think that the issue of a reset and then a polling
loop of checkpower until you get a response that it is ready is the only
safe thing to attempt.
Note that I am waiting on my laptop to arrive and then I can comment
better.
Cheers,
> > I have and offered it to the folks at linuxcare the apmd guys.
> > The ideas were to create an ioctl pair that would/could knock-out a drive
> > and preserve the settings, because the reset command to wake it up flushes
> > the settings. Thus after the wakeup reset, and a checkpower-loop for
> > ready-status in a passive drive query, the completion of the command would
> > set the drive and host back to pre- suspend/hibernate mode.
>
> Something like
>
> CASIO FIVA $B$G%O%$%P!<%M!<%7%g%s$r2DG=$K$9$k(B patch
> Ver. 1.01, for Linux kernel-2.2.13
>
> Copyright (C) 1999 INOUE, Yoshinari e-mail: [EMAIL PROTECTED]
>
> (This is an excerpt for the IDE bits)
>
> --- linux/arch/i386/kernel/apm.c.org Wed Nov 24 17:43:08 1999
> +++ linux/arch/i386/kernel/apm.c Wed Nov 24 17:43:18 1999
> @@ -779,6 +779,12 @@
> unsigned long flags;
> int err;
>
> + if (ide_disk_suspend()) {
> + printk(KERN_NOTICE "apm: suspend: reset disk failed\n");
> + apm_set_power_state(APM_STATE_REJECT);
> + return;
> + }
> +
> #ifndef CONFIG_APM_RTC_IS_GMT
> /*
> * Estimate time zone so that set_time can update the clock
> @@ -807,6 +813,7 @@
> restore_flags(flags);
> #endif
> set_time();
> + ide_disk_resume();
> }
>
> static void standby(void)
> --- linux/drivers/block/ide-disk.c.org Wed Nov 24 17:42:23 1999
> +++ linux/drivers/block/ide-disk.c Thu Nov 25 12:43:10 1999
> @@ -52,6 +52,13 @@
>
> #include "ide.h"
>
> +#ifdef CONFIG_APM
> +#include <linux/apm_bios.h>
> +
> +static ide_drive_t *hda = 0;
> +static int mult_count = -1;
> +#endif
> +
> static void idedisk_bswap_data (void *buffer, int wcount)
> {
> u16 *p = buffer;
> @@ -814,6 +821,10 @@
> continue;
> }
> idedisk_setup(drive);
> +#ifdef CONFIG_APM
> + if (!hda)
> + hda = drive;
> +#endif
> if ((!drive->head || drive->head > 16) && !drive->select.b.lba) {
> printk(KERN_ERR "%s: INVALID GEOMETRY: %d PHYSICAL HEADS?\n",
>drive->name, drive->head);
> (void) idedisk_cleanup(drive);
> @@ -825,6 +836,39 @@
> MOD_DEC_USE_COUNT;
> return 0;
> }
> +#ifdef CONFIG_APM
> +
> +int ide_disk_suspend(void)
> +{
> + int error, retry = 5;
> +
> + if (!hda)
> + return (0);
> + mult_count = hda->mult_count;
> + if (mult_count == hda->id->max_multsect) {
> + mult_count = -1;
> + return (0);
> + }
> + while (retry-- > 0) {
> + error = set_multcount(hda, hda->id->max_multsect);
> + if (!error)
> + return (0);
> + }
> + return (error);
> +}
> +
> +void ide_disk_resume(void)
> +{
> + int retry = 5;
> +
> + if (mult_count >= 0)
> + while (retry-- > 0)
> + if (set_multcount(hda, mult_count) == 0)
> + break;
> + mult_count = -1;
> + return;
> +}
> +#endif
>
> #ifdef MODULE
> int init_module (void)
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to [EMAIL PROTECTED]
> Please read the FAQ at http://www.tux.org/lkml/
>
Andre Hedrick
The Linux ATA/IDE guy
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
Please read the FAQ at http://www.tux.org/lkml/
