On Mon, Jun 13, 2016 at 04:19:10PM -0500, ttha...@opensource.altera.com wrote:
> From: Thor Thayer <ttha...@opensource.altera.com>
>
> In preparation for additional memory module ECCs, add the
> memory initialization functions and helper functions used
> for memory initialization.
>
> Signed-off-by: Thor Thayer <ttha...@opensource.altera.com>
> ---
> v2: Specify INTMODE selection -> IRQ on each ECC error.
> Insert functions above memory-specific functions so that function
> declarations are not required.
> Use ERRINTENS & ERRINTENR registers instead of read/modify/write.
> v3: Changes for common compatibility string:
> - Pass node instead of compatibility string.
> - New altr_init_a10_ecc_device_type() for peripherals.
> - Add __init to altr_init_a10_ecc_block().
> - Add a10_get_irq_mask().
> ---
> drivers/edac/altera_edac.c | 197
> ++++++++++++++++++++++++++++++++++++++++++++
> drivers/edac/altera_edac.h | 8 ++
> 2 files changed, 205 insertions(+)
> +/*
> + * This function uses the memory initialization block in the Arria10 ECC
> + * controller to initialize/clear the entire memory data and ECC data.
> + */
> +static int altr_init_memory_port(void __iomem *ioaddr, int port)
> +{
> + int limit = ALTR_A10_ECC_INIT_WATCHDOG_10US;
> + u32 init_mask = ALTR_A10_ECC_INITA;
> + u32 stat_mask = ALTR_A10_ECC_INITCOMPLETEA;
> + u32 clear_mask = ALTR_A10_ECC_ERRPENA_MASK;
> + int ret = 0;
> +
> + if (port) {
> + init_mask = ALTR_A10_ECC_INITB;
> + stat_mask = ALTR_A10_ECC_INITCOMPLETEB;
> + clear_mask = ALTR_A10_ECC_ERRPENB_MASK;
> + }
Do a
u32 init_mask, stat_mask, clear_mask;
if (port) {
init_mask = ALTR_A10_ECC_INITB;
...
} else {
init_mask = ALTR_A10_ECC_INITA;
...
}
so that you don't have to repeat the assignments in the if (port) case.
> +
> + ecc_set_bits(init_mask, (ioaddr + ALTR_A10_ECC_CTRL_OFST));
> + while (limit--) {
> + if (ecc_test_bits(stat_mask,
> + (ioaddr + ALTR_A10_ECC_INITSTAT_OFST)))
> + break;
> + udelay(1);
> + }
> + if (limit < 0)
> + ret = -EBUSY;
> +
> + /* Clear any pending ECC interrupts */
> + writel(clear_mask, (ioaddr + ALTR_A10_ECC_INTSTAT_OFST));
> +
> + return ret;
> +}
> +
> +/*
> + * Aside from the L2 ECC, the Arria10 ECC memories have a common register
> + * layout so the following functions can be shared between all peripherals.
I don't understand - we're here under
#if defined(CONFIG_EDAC_ALTERA_ETHERNET)
What sharing do you mean?
--
Regards/Gruss,
Boris.
ECO tip #101: Trim your mails when you reply.
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
