Hi Daniel, Please try following changes, On 14 April 2014 15:37, Daniel Lezcano <daniel.lezc...@linaro.org> wrote: > On 04/14/2014 08:29 AM, Chander Kashyap wrote: >> >> Hi Daniel, >> >> I am using ML u-boot and ML kernel with ramdisk as rootfs for my testing. > > > Hi Chander, > > I tried to use u-boot ML but it fails with the error: > > ** Unrecognized filesystem type ** > ** Unrecognized filesystem type ** > ** Unrecognized filesystem type ** > Wrong Image Format for bootm command > ERROR: can't get kernel image! > ARNDALE # fatls mmc 0:2 > ** Unrecognized filesystem type ** > ARNDALE # fatls mmc 0:1
fatls mmc 1:1 > > 0 file(s), 0 dir(s) > > ARNDALE # fatls mmc 0:3 > ** Unrecognized filesystem type ** > ARNDALE # fatls mmc 0: > > In order to set it up I did: > > make arndale_config all CROSS_COMPILE=arm-linux-gnueabi- > > sudo dd if=arndale-bl1.bin of=/dev/mmcblk0 bs=512 seek=1 > sudo dd if=spl/arndale-spl.bin of=/dev/mmcblk0 bs=512 seek=17 > sudo dd if=u-boot-dtb.bin of=/dev/mmcblk0 bs=512 seek=49 > > fdisk -l /dev/mmcblk0 > > Disk /dev/mmcblk0: 3951 MB, 3951034368 bytes > 128 heads, 32 sectors/track, 1884 cylinders, total 7716864 sectors > Units = sectors of 1 * 512 = 512 bytes > Sector size (logical/physical): 512 bytes / 512 bytes > I/O size (minimum/optimal): 512 bytes / 512 bytes > Disk identifier: 0x00000000 > > Device Boot Start End Blocks Id System > /dev/mmcblk0p1 1 8191 4095+ da Non-FS data > /dev/mmcblk0p2 * 8192 114687 53248 c W95 FAT32 (LBA) > /dev/mmcblk0p3 114688 2097151 991232 83 Linux > > Did I missed something ? > > Thanks > -- Daniel > > >> On 13 April 2014 03:49, Victor Kamensky <victor.kamen...@linaro.org> >> wrote: >>> >>> Hi Daniel, >>> >>> Note these patches: >>> >>> >>> https://groups.google.com/a/linaro.org/forum/#!searchin/linaro-networking/Arndale$20hotplug/linaro-networking/MdvG8m_Bjms/YSvvIYKo4NQJ >>> >>> Look at PATCH 1/2. It is about wfi instruction hex code use in >>> CONFIG_THUMB2_KERNEL case. >>> Even if patch tile says BE image the issue is applicable to LE thumb2 >>> issue. Check >>> your kernel config if THUMB2_KERNEL set the issue is applicable to you. >>> >>> Thanks, >>> Victor >>> >>> On 12 April 2014 14:51, Daniel Lezcano <daniel.lezc...@linaro.org> wrote: >>>> >>>> >>>> Hi all, >>>> >>>> I used the image: >>>> >>>> arndale-saucy_server_20140222-611.img >>>> >>>> I boots well but when I unplug CPU1, the kernel crashes. >>>> >>>> It seems related to the AFTR state (an idle state of cpuidle) and the >>>> u-boot >>>> version which is 2013-rc1. It seems this issue does not happen with a >>>> more >>>> recent u-boot (I was not yet able to test it). >>>> >>>> I don't know where to fill the bug for this release. >>>> >>>> Chander, any pointer to the right u-boot version you are using >>>> successfully >>>> ? >>>> >>>> Thanks >>>> >>>> -- Daniel >>>> >>>> -- >>>> <http://www.linaro.org/> Linaro.org │ Open source software for ARM >>>> SoCs >>>> >>>> Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook | >>>> <http://twitter.com/#!/linaroorg> Twitter | >>>> <http://www.linaro.org/linaro-blog/> Blog >>>> >>>> >>>> _______________________________________________ >>>> linaro-dev mailing list >>>> linaro-dev@lists.linaro.org >>>> http://lists.linaro.org/mailman/listinfo/linaro-dev >> >> >> >> > > > -- > <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs > > Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook | > <http://twitter.com/#!/linaroorg> Twitter | > <http://www.linaro.org/linaro-blog/> Blog > -- with warm regards, Chander Kashyap _______________________________________________ linaro-dev mailing list linaro-dev@lists.linaro.org http://lists.linaro.org/mailman/listinfo/linaro-dev
