Hi there,

When booting linaro snapshots on my PandaBoard the system hangs a few seconds 
after the bash prompt is shown (sometimes a little earlier). My first step was 
to enable magic-sysrq but the system doesn't react on them. It looks like it's 
already powered off - very strange. I've tried various hwpacks and headless 
images and also an SD-card image that works works on a pandaboard of a 
colleague (20110127 hwpack with 20110126 headless) but everything fails with 
the same symptoms. I used two different power supplies and several SD cards - 
also no difference. The board itself doesn't seem to be defective as the 
ubuntu-netbook-10.10-preinstalled-netbook-armel+omap4.img runs flawlessly for 
hours. I replaced the 2.6.35 omap4 kernel of the ubuntu 10.10 image with a 
kernel built from the latest git://git.linaro.org/ubuntu/linux-linaro-
natty.git - but then the board hangs again. Attached is the output of the 
serial console. Any hints/suggestions on how to get the linaro kernel working 
on this board are much appreciated.

Regards
Ken
Texas Instruments X-Loader 1.4.4ss (Jan 26 2011 - 10:12:48)         
Reading boot sector
Loading u-boot.bin from mmc


U-Boot 2010.12 (Jan 11 2011 - 05:00:24)

CPU  : OMAP4430
Board: OMAP4 Panda
I2C:   ready
DRAM:  1 GiB
MMC:   OMAP SD/MMC: 0
Using default environment

In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  0 
reading boot.scr

381 bytes read
Running bootscript from mmc0 ...
## Executing script at 82000000
reading uImage

3636192 bytes read
reading uInitrd

4497640 bytes read
## Booting kernel from Legacy Image at 80200000 ...
   Image Name:   Linux
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3636128 Bytes = 3.5 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 81600000 ...
   Image Name:   initramfs
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    4497576 Bytes = 4.3 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.37-1002-linaro-omap (buildd@actinidiaceae) (gcc version 4.5.2 (Ubuntu/Linaro )
[    0.000000] CPU: ARMv7 Processor [411fc092] revision 2 (ARMv7), cr=10c53c7f
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: OMAP4 Panda board
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] OMAP4430 ES2.0
[    0.000000] SRAM: Mapped pa 0x40300000 to va 0xfe400000 size: 0xe000
[    0.000000] FIXME: omap44xx_sram_init not implemented
[    0.000000] PERCPU: Embedded 7 pages/cpu @c0b9c000 s7712 r8192 d12768 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 117602
[    0.000000] Kernel command line: console=tty0 console=ttyO2,115200n8  root=UUID=c042cfbf-a219-40a2-a69d-d0be
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] allocated 2370560 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Memory: 463MB = 463MB total
[    0.000000] Memory: 455056k/455056k available, 19056k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
[    0.000000]     vmalloc : 0xdd000000 - 0xf8000000   ( 432 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdcf00000   ( 463 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .init : 0xc0008000 - 0xc0048000   ( 256 kB)
[    0.000000]       .text : 0xc0048000 - 0xc06d9478   (6726 kB)
[    0.000000]       .data : 0xc06da000 - 0xc0738800   ( 378 kB)
[    0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU-based detection of stalled CPUs is disabled.
[    0.000000] NR_IRQS:402
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at /build/buildd/linux-linaro-omap-2.6.37/arch/arm/mach-omap2/clockdomain.c:868 omap2_)
[    0.000000] clockdomain: OMAP4 wakeup/sleep dependency support is not yet implemented
[    0.000000] Modules linked in:
[    0.000000] [<c005a9a0>] (unwind_backtrace+0x0/0xfc) from [<c008f2a4>] (warn_slowpath_common+0x54/0x64)
[    0.000000] [<c008f2a4>] (warn_slowpath_common+0x54/0x64) from [<c008f348>] (warn_slowpath_fmt+0x30/0x40)
[    0.000000] [<c008f348>] (warn_slowpath_fmt+0x30/0x40) from [<c006b674>] (omap2_clkdm_deny_idle+0x7c/0x88)
[    0.000000] [<c006b674>] (omap2_clkdm_deny_idle+0x7c/0x88) from [<c006b7f8>] (clkdm_init+0x178/0x1b0)
[    0.000000] [<c006b7f8>] (clkdm_init+0x178/0x1b0) from [<c00102bc>] (omap2_init_common_hw+0x24/0x154)
[    0.000000] [<c00102bc>] (omap2_init_common_hw+0x24/0x154) from [<c001627c>] (omap4_panda_init_irq+0x10/0x1)
[    0.000000] [<c001627c>] (omap4_panda_init_irq+0x10/0x1c) from [<c000c3d4>] (init_IRQ+0x14/0x18)
[    0.000000] [<c000c3d4>] (init_IRQ+0x14/0x18) from [<c0008bc4>] (start_kernel+0x1f8/0x350)
[    0.000000] [<c0008bc4>] (start_kernel+0x1f8/0x350) from [<80008038>] (0x80008038)
[    0.000000] ---[ end trace da227214a82491b7 ]---
[    0.000000] omap_hwmod: dpll_mpu_m2_ck: missing clockdomain for dpll_mpu_m2_ck.
[    0.000000] GPMC revision 6.0
[    0.000000] OMAP GPIO hardware version 0.1
[    0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.37-1002-linaro-omap (buildd@actinidiaceae) (gcc version 4.5.2 (Ubuntu/Linaro )
[    0.000000] CPU: ARMv7 Processor [411fc092] revision 2 (ARMv7), cr=10c53c7f
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: OMAP4 Panda board
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] OMAP4430 ES2.0
[    0.000000] SRAM: Mapped pa 0x40300000 to va 0xfe400000 size: 0xe000
[    0.000000] FIXME: omap44xx_sram_init not implemented
[    0.000000] PERCPU: Embedded 7 pages/cpu @c0b9c000 s7712 r8192 d12768 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 117602
[    0.000000] Kernel command line: console=tty0 console=ttyO2,115200n8  root=UUID=c042cfbf-a219-40a2-a69d-d0be
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] allocated 2370560 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Memory: 463MB = 463MB total
[    0.000000] Memory: 455056k/455056k available, 19056k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
[    0.000000]     vmalloc : 0xdd000000 - 0xf8000000   ( 432 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdcf00000   ( 463 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .init : 0xc0008000 - 0xc0048000   ( 256 kB)
[    0.000000]       .text : 0xc0048000 - 0xc06d9478   (6726 kB)
[    0.000000]       .data : 0xc06da000 - 0xc0738800   ( 378 kB)
[    0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU-based detection of stalled CPUs is disabled.
[    0.000000] NR_IRQS:402
[    0.000000] ------------[ cut here ]------------
[    0.000000] WARNING: at /build/buildd/linux-linaro-omap-2.6.37/arch/arm/mach-omap2/clockdomain.c:868 omap2_)
[    0.000000] clockdomain: OMAP4 wakeup/sleep dependency support is not yet implemented
[    0.000000] Modules linked in:
[    0.000000] [<c005a9a0>] (unwind_backtrace+0x0/0xfc) from [<c008f2a4>] (warn_slowpath_common+0x54/0x64)
[    0.000000] [<c008f2a4>] (warn_slowpath_common+0x54/0x64) from [<c008f348>] (warn_slowpath_fmt+0x30/0x40)
[    0.000000] [<c008f348>] (warn_slowpath_fmt+0x30/0x40) from [<c006b674>] (omap2_clkdm_deny_idle+0x7c/0x88)
[    0.000000] [<c006b674>] (omap2_clkdm_deny_idle+0x7c/0x88) from [<c006b7f8>] (clkdm_init+0x178/0x1b0)
[    0.000000] [<c006b7f8>] (clkdm_init+0x178/0x1b0) from [<c00102bc>] (omap2_init_common_hw+0x24/0x154)
[    0.000000] [<c00102bc>] (omap2_init_common_hw+0x24/0x154) from [<c001627c>] (omap4_panda_init_irq+0x10/0x1)
[    0.000000] [<c001627c>] (omap4_panda_init_irq+0x10/0x1c) from [<c000c3d4>] (init_IRQ+0x14/0x18)
[    0.000000] [<c000c3d4>] (init_IRQ+0x14/0x18) from [<c0008bc4>] (start_kernel+0x1f8/0x350)
[    0.000000] [<c0008bc4>] (start_kernel+0x1f8/0x350) from [<80008038>] (0x80008038)
[    0.000000] ---[ end trace da227214a82491b7 ]---
[    0.000000] omap_hwmod: dpll_mpu_m2_ck: missing clockdomain for dpll_mpu_m2_ck.
[    0.000000] GPMC revision 6.0
[    0.000000] OMAP GPIO hardware version 0.1
[    0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [tty0] enabled
[    0.000000] Calibrating delay loop... 2013.49 BogoMIPS (lpj=7864320)
[    0.000000] pid_max: default: 32768 minimum: 301
[    0.000000] Security Framework initialized
[    0.000000] AppArmor: AppArmor initialized
[    0.000000] Yama: becoming mindful.
[    0.000000] Mount-cache hash table entries: 512
[    0.000000] Initializing cgroup subsys ns
[    0.000000] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup.
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Initializing cgroup subsys memory
[    0.000000] Initializing cgroup subsys devices
[    0.000000] Initializing cgroup subsys freezer
[    0.000000] CPU: Testing write buffer coherency: ok
[    0.000000] Calibrating local timer... 491.18MHz.
[    0.000000] L310 cache controller enabled
[    0.000000] l2x0: 16 ways, CACHE_ID 0x410000c4, AUX_CTRL 0x0e070000, Cache size: 1048576 B
[    0.000000] CPU1: Booted secondary processor
[    0.000000] Brought up 2 CPUs
[    0.000000] SMP: Total of 2 processors activated (3976.57 BogoMIPS).
[    0.000000] devtmpfs: initialized
[    0.000000] regulator: core version 0.5
[    0.000000] regulator: dummy: 
[    0.000000] NET: Registered protocol family 16
[    0.000000] mux: Could not set signal i2c2_scl.i2c2_scl
[    0.000000] mux: Could not set signal i2c2_sda.i2c2_sda
[    0.000000] mux: Could not set signal i2c3_scl.i2c3_scl
[    0.000000] mux: Could not set signal i2c3_sda.i2c3_sda
[    0.000000] mux: Could not set signal i2c4_scl.i2c4_scl
[    0.000000] mux: Could not set signal i2c4_sda.i2c4_sda
[    0.000000] Trying to unpack rootfs image as initramfs...
[    0.000000] mux: Could not set signal usbb1_ulpiphy_stp
[    0.000000] mux: Could not set signal usbb1_ulpiphy_clk
[    0.000000] mux: Could not set signal usbb1_ulpiphy_dir
[    0.000000] mux: Could not set signal usbb1_ulpiphy_nxt
[    0.000000] mux: Could not set signal usbb1_ulpiphy_dat0
[    0.000000] mux: Could not set signal usbb1_ulpiphy_dat1
[    0.000000] mux: Could not set signal usbb1_ulpiphy_dat2
[    0.000000] mux: Could not set signal usbb1_ulpiphy_dat3
[    0.000000] mux: Could not set signal usbb1_ulpiphy_dat4
[    0.000000] mux: Could not set signal usbb1_ulpiphy_dat5
[    0.000000] mux: Could not set signal usbb1_ulpiphy_dat6
[    0.000000] mux: Could not set signal usbb1_ulpiphy_dat7
[    0.000000] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
[    0.000000] hw-breakpoint: 1 breakpoint reserved for watchpoint single-step.
[    0.000000] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.000000] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.000000] omap_init_sham: platform not supported
[    0.000000] OMAP DMA hardware revision 0.0
[    0.014862] bio: create slab <bio-0> at 0
[    0.020019] SCSI subsystem initialized
[    0.024383] usbcore: registered new interface driver usbfs
[    0.030181] usbcore: registered new interface driver hub
[    0.035888] usbcore: registered new device driver usb
[    0.052429] i2c_omap i2c_omap.1: bus 1 rev4.0 at 400 kHz
[    0.136566] Skipping twl internal clock init and using bootloader value (unknown osc rate)
[    0.146759] twl6030: PIH (irq 39) chaining IRQs 368..387
[    0.213897] Freeing initrd memory: 4392K
[    0.236053] regulator: VMMC: 1200 <--> 3000 mV at 3000 mV normal standby
[    0.243988] regulator: VPP: 1800 <--> 2500 mV at 1900 mV normal standby
[    0.251800] regulator: VUSIM: 1200 <--> 2900 mV at 1800 mV normal standby
[    0.259368] regulator: VANA: 2100 mV normal standby
[    0.264923] regulator: VCXIO: 1800 mV normal standby
[    0.270599] regulator: VDAC: 1800 mV normal standby
[    0.276184] regulator: VUSB: 3300 mV normal standby
[    0.282257] regulator: VAUX1_6030: 1000 <--> 3000 mV at 1800 mV normal standby
[    0.290710] regulator: VAUX2_6030: 1200 <--> 2800 mV at 1800 mV normal standby
[    0.299163] regulator: VAUX3_6030: 1000 <--> 3000 mV at 1200 mV normal standby
[    0.319213] i2c_omap i2c_omap.2: bus 2 rev4.0 at 400 kHz
[    0.334472] i2c_omap i2c_omap.3: bus 3 rev4.0 at 400 kHz
[    0.349700] i2c_omap i2c_omap.4: bus 4 rev4.0 at 400 kHz
[    0.355773] Advanced Linux Sound Architecture Driver Version 1.0.23.
[    0.362701] NetLabel: Initializing
[    0.366271] NetLabel:  domain hash size = 128
[    0.370849] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.376068] NetLabel:  unlabeled traffic allowed by default
[    0.381896] Switching to clocksource 32k_counter
[    0.391632] AppArmor: AppArmor Filesystem Enabled
[    0.402862] NET: Registered protocol family 2
[    0.407592] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.415374] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.423065] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[    0.430145] TCP: Hash tables configured (established 16384 bind 16384)
[    0.436950] TCP reno registered
[    0.440277] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.446380] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.453155] NET: Registered protocol family 1
[    0.457763] NetWinder Floating Point Emulator V0.97 (double precision)
[    0.464904] ------------[ cut here ]------------
[    0.469757] WARNING: at /build/buildd/linux-linaro-omap-2.6.37/arch/arm/mach-omap2/pm.c:64 _init_omap_devic)
[    0.481018] _init_omap_device: could not find omap_hwmod for iva
[    0.487243] Modules linked in:
[    0.490509] [<c005a9a0>] (unwind_backtrace+0x0/0xfc) from [<c008f2a4>] (warn_slowpath_common+0x54/0x64)
[    0.500305] [<c008f2a4>] (warn_slowpath_common+0x54/0x64) from [<c008f348>] (warn_slowpath_fmt+0x30/0x40)
[    0.510223] [<c008f348>] (warn_slowpath_fmt+0x30/0x40) from [<c0065134>] (_init_omap_device+0x90/0xc0)
[    0.519897] [<c0065134>] (_init_omap_device+0x90/0xc0) from [<c0011c10>] (omap2_common_pm_init+0x24/0x84)
[    0.529846] [<c0011c10>] (omap2_common_pm_init+0x24/0x84) from [<c004869c>] (do_one_initcall+0x34/0x188)
[    0.539672] [<c004869c>] (do_one_initcall+0x34/0x188) from [<c0008e3c>] (kernel_init+0x120/0x1c4)
[    0.548889] [<c0008e3c>] (kernel_init+0x120/0x1c4) from [<c0053ed4>] (kernel_thread_exit+0x0/0x8)
[    0.558105] ---[ end trace da227214a82491b8 ]---
[    0.563018] ------------[ cut here ]------------
[    0.567871] WARNING: at /build/buildd/linux-linaro-omap-2.6.37/arch/arm/mach-omap2/pm.c:64 _init_omap_devic)
[    0.579132] _init_omap_device: could not find omap_hwmod for dsp
[    0.585388] Modules linked in:
[    0.588623] [<c005a9a0>] (unwind_backtrace+0x0/0xfc) from [<c008f2a4>] (warn_slowpath_common+0x54/0x64)
[    0.598358] [<c008f2a4>] (warn_slowpath_common+0x54/0x64) from [<c008f348>] (warn_slowpath_fmt+0x30/0x40)
[    0.608276] [<c008f348>] (warn_slowpath_fmt+0x30/0x40) from [<c0065134>] (_init_omap_device+0x90/0xc0)
[    0.617950] [<c0065134>] (_init_omap_device+0x90/0xc0) from [<c0011c40>] (omap2_common_pm_init+0x54/0x84)
[    0.627868] [<c0011c40>] (omap2_common_pm_init+0x54/0x84) from [<c004869c>] (do_one_initcall+0x34/0x188)
[    0.637725] [<c004869c>] (do_one_initcall+0x34/0x188) from [<c0008e3c>] (kernel_init+0x120/0x1c4)
[    0.646942] [<c0008e3c>] (kernel_init+0x120/0x1c4) from [<c0053ed4>] (kernel_thread_exit+0x0/0x8)
[    0.656127] ---[ end trace da227214a82491b9 ]---
[    0.661163] audit: initializing netlink socket (disabled)
[    0.666809] type=2000 audit(1.437:1): initialized
[    0.774200] VFS: Disk quotas dquot_6.5.2
[    0.778533] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.787536] fuse init (API version 7.15)
[    0.791992] msgmni has been set to 897
[    0.796569] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.804290] io scheduler noop registered
[    0.808410] io scheduler deadline registered
[    0.812927] io scheduler cfq registered (default)
[    0.818511] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.207153] omap-hsuart.0: ttyO0 at MMIO 0x4806a000 (irq = 104) is a OMAP UART0
[    1.332061] omap-hsuart.1: ttyO1 at MMIO 0x4806c000 (irq = 105) is a OMAP UART1
[    1.457061] omap-hsuart.2: ttyO2 at MMIO 0x48020000 (irq = 106) is a OMAP UART2
[    1.464660] console [ttyO2] enabled, bootconsole disabled
[    1.464660] console [ttyO2] enabled, bootconsole disabled
[    1.582092] omap-hsuart.3: ttyO3 at MMIO 0x4806e000 (irq = 102) is a OMAP UART3
[    1.711212] brd: module loaded
[    1.716552] loop: module loaded
[    1.720581] omap2-nand driver initializing
[    1.725860] PPP generic driver version 2.4.2
[    1.730438] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
[    1.740509] CSLIP: code copyright 1989 Regents of the University of California.
[    1.748138] SLIP linefill/keepalive option.
[    1.752593] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.759552] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[    1.765472] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
[    1.800872] ehci-omap ehci-omap.0: irq 109, io mem 0x4a064c00
[    1.816436] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[    1.822845] hub 1-0:1.0: USB hub found
[    1.826751] hub 1-0:1.0: 3 ports detected
[    1.855712] mice: PS/2 mouse device common for all mice
[    1.861450] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
[    1.868286] twl_rtc twl_rtc: Power up reset detected.
[    1.876098] twl_rtc twl_rtc: Enabling TWL-RTC.
[    1.881927] device-mapper: uevent: version 1.0.3
[    1.887115] device-mapper: ioctl: 4.18.0-ioctl (2010-06-29) initialised: dm-de...@redhat.com
[    1.896057] device-mapper: multipath: version 1.1.1 loaded
[    1.901794] device-mapper: multipath round-robin: version 1.0.0 loaded
[    1.908996] cpuidle: using governor ladder
[    1.913269] cpuidle: using governor menu
[    1.917358] sdhci: Secure Digital Host Controller Interface driver
[    1.923797] sdhci: Copyright(c) Pierre Ossman
[    1.935302] ALSA device list:
[    1.938385]   No soundcards found.
[    1.942657] TCP cubic registered
[    1.946533] NET: Registered protocol family 10
[    1.952087] lo: Disabled Privacy Extensions
[    1.956970] NET: Registered protocol family 17
[    1.961669] Registering the dns_resolver key type
[    1.966613] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 1
[    1.974639] ThumbEE CPU extension supported.
[    1.979095] Power Management for TI OMAP4.
[    1.983398] clock: disabling unused clocks to save power
[    1.989440] registered taskstats version 1
[    1.993804] omapfb omapfb: no displays
[    1.997741] omapfb omapfb: failed to setup omapfb
[    2.002655] omapfb: probe of omapfb failed with error -22
[    2.008789] regulator_init_complete: incomplete constraints, leaving VAUX3_6030 on
[    2.017181] regulator_init_complete: incomplete constraints, leaving VAUX2_6030 on
[    2.028503] regulator_init_complete: incomplete constraints, leaving VAUX1_6030 on
[    2.036865] regulator_init_complete: incomplete constraints, leaving VUSB on
[    2.044647] regulator_init_complete: incomplete constraints, leaving VDAC on
[    2.052459] regulator_init_complete: incomplete constraints, leaving VCXIO on
[    2.060333] regulator_init_complete: incomplete constraints, leaving VANA on
[    2.068145] regulator_init_complete: incomplete constraints, leaving VUSIM on
[    2.076049] regulator_init_complete: incomplete constraints, leaving VPP on
[    2.085113] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[    2.093933] Freeing init memory: 256K
[    2.097778] mmc0: host does not support reading read-only switch. assuming write-enable.
[    2.121215] mmc0: new high speed SDHC card at address b368
[    2.127197] mmcblk0: mmc0:b368 SD    15.0 GiB 
[    2.132843]  mmcblk0: p1 p2
Loading, please wait...
[    2.152404] usb 1-1: new high speed USB device using ehci-omap and address 2
[    2.174804] udev[65]: starting version 165
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
[    2.310363] hub 1-1:1.0: USB hub found
[    2.316497] hub 1-1:1.0: 5 ports detected
Begin: Running /scripts/local-premount ... done.
[    2.437316] EXT3-fs (mmcblk0p2): recovery required on readonly filesystem
[    2.444519] EXT3-fs (mmcblk0p2): write access will be enabled during recovery
[    2.453308] EXT3-fs: barriers not enabled
[    2.474060] kjournald starting.  Commit interval 5 seconds
[    2.479797] EXT3-fs (mmcblk0p2): recovery complete
[    2.489593] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... done.
[    2.621398] usb 1-1.1: new high speed USB device using ehci-omap and address 3
[    2.832397] usb 1-1.2: new full speed USB device using ehci-omap and address 4
[    2.961273] hub 1-1.2:1.0: USB hub found
[    2.966278] hub 1-1.2:1.0: 4 ports detected

Last login: Thu Jan 27 11:57:25 UTC 2011 on tty1
Welcome to Ubuntu natty (development branch) (GNU/Linux 2.6.37-1002-linaro-omap armv7l)

 * Documentation:  http://www.linaro.org
root@localhost:~#
_______________________________________________
linaro-dev mailing list
linaro-dev@lists.linaro.org
http://lists.linaro.org/mailman/listinfo/linaro-dev

Reply via email to