Hello Kristian,
On 04.11.2017 21:53, Kristian Evensen wrote:
The Unielec U7621-6
(http://www.unielecinc.com/q/news/cn/p/product/detail.html?qd_guid=pyrEjfTmYf)
is an MT7621-based router with the following specifications:
I got the same board last week and had some initial support ready
locally. I pushed it now to my staging tree, please have a look:
https://git.lede-project.org/?p=lede/pepe2k/staging.git;a=shortlog;h=refs/heads/ramips_unielec-u7621-06
Maybe we can combine our patches and work out a common version.
Please, find also my comments below.
--
Cheers,
Piotr
[snip]
Notes:
* According to the specifications on the Unielec website, two LEDs
should be controllable via GPIO. I was not able to find the pins.
GPIOs 10, 11 and 12 control LEDs 3, 4 and 5 in top row. At least on my
board, some of these LEDs were rotated (wrong polarization).
* The device can be delivered with different amounts of RAM and
storage. I have only added support for devices with 256MB RAM and 16MB
storage, as that is the configuration of my device. However, I have
added all the required infrastructure for making adding support for the
other configurations easy.
AFAIK, board with 256/16 MB is the default one (mass production?). Any
change means MOQ and customized version. The default one can be easily
purchased from Ali..., directly from the vendor.
* I have assumed that the placement of wifi cards will be as on the image on
the Unielec website linked to above.
I have problem with this and I don't know how we should proceed here
(Mathias, what do you think?).
Actually, the board by default comes without any Wi-Fi card installed
and they need to be ordered separately (if someone needs them at all).
Personally, I don't think we should force any type of card and/or order
in slots. The board comes with two miniPCIe slots which can be used for
almost anything. I've been testing it with ath9k and mt7603 based cards,
a different configuration than yours :)
* The factory firmware reads the MAC address from offset e000 on the
factory partition. On my device, this offset contains 0xffs, but I have
chosen to keep the offset in the dts to ensure we are consistent with
the factory firmware.
AFAIK, the firmware vendor provides board with doesn't come from them.
They installed some version dedicated for PandoraBox PBR-M1.
There is also some dedicated Padavan version but I have no idea where it
can be downloaded from.
Installation:
See Recovery below. The router comes pre-installed with OpenWRT (Pandora
Box), but sysupgrade fails due to board name mismatch.
sysupgrade -F ...
Recovery:
The U7621-6 supports web recovery. If you keep the reset-button pressed
for ~5 seconds during boot, a webserver is started.Your machine will be
assigned an IP through DHCP, and the router has address 192.168.1.1. The
recovery website is in Chinese, but is easy to use. Click on the second
item in the list to access the recovery page, then the second item on
the next page is where you select the firmware. In order to start the
recovery, you click the button at the bottom.
At least on my board, button just stops autobooting process. Web server
seems to be enabled in the bootloader all the time - with a static IP on
my PC I can access it even during autobooting countdown.
Signed-off-by: Kristian Evensen <kristian.even...@gmail.com>
---
.../linux/ramips/base-files/etc/board.d/02_network | 1 +
target/linux/ramips/base-files/lib/ramips.sh | 3 +
.../ramips/base-files/lib/upgrade/platform.sh | 1 +
target/linux/ramips/dts/U7621-6-256M-16M.dts | 54 ++++++++
target/linux/ramips/dts/U7621-6.dtsi | 147 +++++++++++++++++++++
target/linux/ramips/image/mt7621.mk | 9 ++
6 files changed, 215 insertions(+)
create mode 100644 target/linux/ramips/dts/U7621-6-256M-16M.dts
create mode 100644 target/linux/ramips/dts/U7621-6.dtsi
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network
b/target/linux/ramips/base-files/etc/board.d/02_network
index 1c8505e8c7..8530ca5170 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -102,6 +102,7 @@ ramips_setup_interfaces()
r6220|\
sap-g3200u3|\
sk-wb8|\
+ u7621-6-256M-16M|\
The board name is U7621-06 (not U7621-6).
As the 256/16 MB configuration is (seems to be) the default one, I don't
see any reason for a different board name.
[snip]
+/dts-v1/;
+
+#include "U7621-6.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "unielec,u7621-6-256m-16m", "unielec,u7621-6",
"mediatek,mt7621-soc";
+ model = "Unielec U7621-6 (256M RAM/16M flash)";
According to the vendor website and datasheet, it should be "UniElec
U7621-06".
+ gpio_export {
+ compatible = "gpio-export";
+ #size-cells = <0>;
+
+ modem_power {
+ gpio-export,name = "modem_power";
This is not a "power" control line. Actually, GPIO16 is connected with
PERST# signal in miniPCIe slot (the one for LTE/mSATA). Most of miniPCIe
cards (including modems) use this pin for reset (active low).
+ gpio-export,output = <1>;
+ gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&sdhci {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhci_pins>;
+};
+
+&spi0 {
+ status = "okay";
+
+ m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+ m25p,chunked-io = <32>;
+
+ partition@0 {
+ label = "u-boot";
This board doesn't use U-Boot.
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition@30000 {
+ label = "u-boot-env";
This partition, at least on my piece, contains some configuration data
which looks like from MediaTek SDK based firmware (leftovers?). It's
definitely not an U-Boot environment.
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ factory: partition@40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ firmware: partition@50000 {
+ label = "firmware";
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+
+ pcie1 {
+ wifi@14c3,7612 {
+ compatible = "pci14c3,7612";
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&factory 0x8000>;
+ ieee80211-freq-limit = <5000000 6000000>;
+ };
+ };
+
+ pcie2 {
+ wifi@14c3,7602 {
+ compatible = "pci14c3,7602";
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&factory 0x0000>;
+ ieee80211-freq-limit = <2400000 2500000>;
+ };
+ };
Does your board contains correct eeprom data in factory partition,
including MAC addresses? Can you share your factory partition dumps?
+};
+
+ðernet {
+ mtd-mac-address = <&factory 0xe000>;
My board has a a MAC address at 0xe006.
+ mediatek,portmap = "llllw";
+};
+
+&pinctrl {
+ state_default: pinctrl0 {
+ gpio {
+ ralink,group = "wdt", "jtag";
+ ralink,function = "gpio";
+ };
+ };
+};
diff --git a/target/linux/ramips/image/mt7621.mk
b/target/linux/ramips/image/mt7621.mk
index 8bd7e0318f..1bdd0024e4 100644
--- a/target/linux/ramips/image/mt7621.mk
+++ b/target/linux/ramips/image/mt7621.mk
@@ -225,6 +225,15 @@ define Device/timecloud
endef
TARGET_DEVICES += timecloud
+define Device/u7621-6-256M-16M
+ DTS := U7621-6-256M-16M
+ IMAGE_SIZE := 16777216
+ DEVICE_TITLE := Unielec U7621-6 (256M RAM/16M flash)
+ DEVICE_PACKAGES := kmod-ata-core kmod-ata-ahci kmod-sdhci-mt7620 kmod-mt76x2
kmod-usb3 \
+ kmod-usb-ledtrig-usbport wpad-mini
+endef
+TARGET_DEVICES += u7621-6-256M-16M
+
define Device/ubnt-erx
DTS := UBNT-ERX
FILESYSTEMS := squashfs
_______________________________________________
Lede-dev mailing list
Lede-dev@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/lede-dev
