Ok, I tried "git request-pull", I assume that it has been submitted ok, how do I know/track it?
[graham@tyr mirror-lede]$ git request-pull f8abb68e3a1b78ff5a8d616994daa9721fe8fc83 https://github.com/Xotic750/mirror-lede.git evg2000 The following changes since commit f8abb68e3a1b78ff5a8d616994daa9721fe8fc83: tools/cmake: bump to 3.5.2 (2016-05-13 17:03:54 +0200) are available in the git repository at: https://github.com/Xotic750/mirror-lede.git evg2000 for you to fetch changes up to c2f97ed220ad8eeb182e80c0fc006ece966679aa: Ran 'make target/linux/refresh V=s' after update to kernel 4.4.10 from 4.4.8 where the initial patch was added. (2016-05-14 00:34:17 +0200) ---------------------------------------------------------------- Xotic750 (2): Add initial support for EVG2000 Ran 'make target/linux/refresh V=s' after update to kernel 4.4.10 from 4.4.8 where the initial patch was added. target/linux/brcm63xx/base-files/etc/board.d/01_leds | 7 +++++ target/linux/brcm63xx/base-files/etc/board.d/02_network | 1 + target/linux/brcm63xx/base-files/etc/diag.sh | 3 +++ target/linux/brcm63xx/base-files/etc/uci-defaults/09_fix_crc | 2 +- target/linux/brcm63xx/base-files/lib/brcm63xx.sh | 3 +++ target/linux/brcm63xx/base-files/lib/preinit/05_init_interfaces_brcm63xx | 1 + target/linux/brcm63xx/dts/evg2000.dts | 103 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ target/linux/brcm63xx/image/Makefile | 2 ++ target/linux/brcm63xx/patches-4.1/805-board_EVG2000.patch | 62 +++++++++++++++++++++++++++++++++++++++++++ target/linux/brcm63xx/patches-4.4/202-MTD-DEVICES-m25p80-use-parsers-if-provided-in-flash-.patch | 2 +- target/linux/brcm63xx/patches-4.4/203-MTD-DEVICES-m25p80-add-support-for-limiting-reads.patch | 4 +-- target/linux/brcm63xx/patches-4.4/414-MTD-m25p80-allow-passing-pp_data.patch | 2 +- target/linux/brcm63xx/patches-4.4/805-board_EVG2000.patch | 62 +++++++++++++++++++++++++++++++++++++++++++ target/linux/brcm63xx/profiles/netgear.mk | 10 +++++++ target/linux/generic/patches-4.4/032-fq_codel-add-batch-ability-to-fq_codel_drop.patch | 4 +-- target/linux/generic/patches-4.4/330-MIPS-kexec-Accept-command-line-parameters-from-users.patch | 10 +++---- target/linux/generic/patches-4.4/531-debloat_lzma.patch | 33 ++++++++++++----------- target/linux/generic/patches-4.4/645-bridge_multicast_to_unicast.patch | 5 ++-- target/linux/generic/patches-4.4/834-ledtrig-libata.patch | 4 +-- 19 files changed, 289 insertions(+), 31 deletions(-) create mode 100644 target/linux/brcm63xx/dts/evg2000.dts create mode 100644 target/linux/brcm63xx/patches-4.1/805-board_EVG2000.patch create mode 100644 target/linux/brcm63xx/patches-4.4/805-board_EVG2000.patch On 16 May 2016 at 12:24, Conor O'Gorman <i...@conorogorman.net> wrote: > On 16/05/16 11:14, Graham Fairweather wrote: >> >> Everything that I read talks about creating PRs when you have forked >> from another github repo, and I have successfully create PRs in this >> situation in the past. I have not seen any information about how to >> create a PR when my repo was forked from a git repo that is hosted >> outside of github. When I go to github and choose create PR, I can >> only create it to branches within my fork, the upstream >> (http://git.lede-project.org/openwrt/source.git) is not listed. Is >> there a github repo that I should have forked from instead? >> > If you have a publicly accessible git repository you can use "git > request-pull" > https://git-scm.com/docs/git-request-pull > > If you are using github you can fork from > https://github.com/lede-project/source > > _______________________________________________ Lede-dev mailing list Lede-dev@lists.infradead.org http://lists.infradead.org/mailman/listinfo/lede-dev
