On 6/5/2022 12:28 PM, Flesner via KRnet wrote:
The EAA has an easy to read article on flutter and gives you the
basics in the first page or two. I'm assuming even non-[eaa members
can load the site. If not, advise, and I'll cut and past.
https://www.eaa.org/eaa/aircraft-building/builderresources/next-steps-after-your-airplane-is-built/operating-articles/general-operation/control-surface-flutter-problems
Larry Flesner
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
It's short. Here it is.............., every builder should have a set of
Tony's books...............
Control Surface Flutter Problems
By Tony Bingelis (originally published in EAA Sport Aviation, July 1979)
December 01, 1993
July 01, 1993
FLUTTER? WELL, SIR, flutter is what a flag does wildly on the flag pole
on those days when it is too windy for you to fly. But to better relate
it to our subject, it should be described as a potentially destructive
vibration or buffeting of an aircraft due to an out-of-balance condition
of one or more of its control surfaces.
Now, imagine one of your control surfaces acting like a flag in the
breeze . . . in flight at 100 or 200 mph. How long do you think it would
stay with the airplane? Not for long, I'll wager!
Most of us are aware that the flutter problem is a complex one and it
has been around aviation for a long time. So long that flutter
specialists must be wallowing around knee deep in the accumulation of
flutter fodder generated from years of research and testing.
Fortunately, there are a few useful assumptions and certain recognized
`good practices' which have been sifted out and any builder willing to
apply the guidelines can do much to avoid having a flutter problem. But
before I continue, let me discuss a few terms and phrases.
*Static Balance*
Static balance - A condition that exists when an object (wheel,
propeller, control surface, anything) remains stationary while supported
on, or suspended from its own center of gravity. Relating this more
specifically to our subject, it also means balancing a control surface
while it is at rest (not in flight).
Automobile wheels, as you know, can be balanced statically (while at
rest). A more effective way, however, is dynamic balancing (spin
balancing). The dynamic balance of aircraft surfaces is similarly
effective but homebuilders really have no practical way of working out
the dynamic balance of a control surface subjected to the stresses of
flight. For this reason, they must fall back on what might be called a
`good practices concept' and assume that, for all practical purposes,
when a control surface is properly mass balanced in its static
condition, it should also be in dynamic balance. If, in principle, the
main objective of dynamic balance is to prevent or minimize torsional
stress in flight, we can accomplish this adequately by evenly
distributing the mass balance weight along the span of the control surface.
Broadly speaking, to attain a static balance state in a control surface,
we add lead weight to the nose until the center of gravity falls on the
hinge axis. Let me expand on this a bit.
For example, if you were to suspend a control surface from its hinge
axis, one of three static balance conditions would become immediately
apparent to you.
1. If the control surface assumes a trailing-edge-low attitude, it is
statically underbalanced and a tail-heavy condition exists. See *Figure 1*.
Operating
2. If the control surface remains in a level (horizontal) attitude, it
is said to be statically 100% balanced and its center of gravity (cg) is
co-located with the hinge axis.
3. Should the trailing edge of the control surface rise some position
above a horizontal plane, an overbalance condition is apparent.
Two of the three conditions described above result in a control surface
that will have a fairly predictable flutter-free flight performance. The
one that is 100% balanced to a level attitude should consistently give
good results. The other surface having a slight nose down attitude is a
typical overbalance condition essential for good results in
high-performance aircraft. Conversely, the static underbalance, or tail
heavy condition first described, is the least desirable as it may result
in unpredictable flight performance.
The conventional flap type (aileron, elevator, rudder) control surface,
as constructed, is typically tail-heavy. That is to say, most of its
structure is distributed behind the hinge axis. It is this sort of
tail-heavy out-of-balance condition that is generally considered to be
the major cause of control surface flutter and buffeting incidents.
True, speed through the air is also a factor and there is no doubt that
flutter is a more frequent occurence in high performance aircraft than
it is with the slower varieties. However, it would be dangerous to
assume that slower homebuilts are immune from such a propensity. I'll
bet you have heard many times that homebuilts having cruising speeds
under 150 mph were exempt from the flutter problem. Don't you believe
it! Any airplane can experience flutter . . . even your light and slow
VW-powered job under certain conditions.
Does this mean that you must balance the control surfaces of your
project even though the plans don't call for it? Not at all. Undoubtedly
the prototype of the airplane you are building was built and flown
without having exhibited flutter tendencies and the designer, therefore,
found no need to require static balancing of the control surfaces.
However, you should understand that, although many other examples of
this same design may have been built and flown, there is no assurance
that yours will likewise be free of flutter problems.
The only way you can prove your airplane to be free of flutter
tendencies is to flight test it with that purpose in mind. This is a
potentially dangerous adventure and must be done only under carefully
controlled conditions. You must prove that your airplane is
controllable, free from flutter, and will be safe to fly. No amount of
reassurance derived from theoretical calculations can substitute for
this requirement.
*Other Flutter Provoking Conditions*
Although there is less risk of encountering flutter in slower aircraft
than in high performance types, individual builders can cause changes,
inadvertently, which could introduce flutter tendencies. For example, a
wing lacking torsional rigidity could induce a bad case of aileron
flutter even at the relatively low airspeeds generally associated with
low and medium-performance aircraft.
A newly constructed aileron or elevator that is excessively heavy (due
to the use of heavier substitute materials or uncalled for
reinforcements) can be flutter-prone. Flutter is most difficult to
suppress in very large or heavy control surfaces and the balance weight
requirement becomes excessive.
Would it surprise you to learn that even time-tested production-line
aircraft are not immune to the flutter phenomenon? True! The reason
being that anytime anything changes the balance of the control surfaces
it may induce flutter in an aircraft that has had no history of such
tendencies. For example, there have been instances where flutter
developed simply because mud adhered to the control surfaces following
muddy field operation.
In an incident reported by the FAA, moisture had collected inside the
ailerons during winter operations and had frozen (seems to happen every
winter) thereby causing an unbalanced condition that was not detected
during the preflight . . . result? In-flight flutter and an accident.
During the long days and nights in the life of an aircraft many changes
take place. Dirt accumulates inside the control surfaces, patches are
added to repair dings and tears, and in time, the surfaces are
repainted. All of these things cause a cumulative change in the mass
balance of the control surface. At some point, the amount of change
becomes just too much . . . and increases the risk of flutter if no
steps are taken to rebalance the reworked surface.
Loose balance weights, water absorption in foam structures, improperly
located or clogged drain holes are all elements which could contribute
to an aerodynamic imbalance situation and result in flutter.
Avoid free play or slack in the control cables. Stiffness in the control
system does have a useful damping effect on the control surfaces further
inhibiting flutter tendencies. However, this should not be completely
relied upon as later, in service, the wear and occasional lubrication
could free the system of much of its original friction and result in an
increased risk of flutter.
Adding a fixed trim tab to an aileron can further upset a marginal
balance condition.
Controllable trim tabs, too, can be a problem. Trim tab control linkage
failures and trim tabs with loose or improperly installed and adjusted
linkages have caused a considerable number of accidents and near
accidents by exciting flutter in the control surfaces to which they are
attached. A recent incident of that nature has just come to my
attention. Involved was a widely built and proven design . . . the staid
ol’ Emeraude. Here's how it happened.
*Flutter . . . A First Hand Account*
"I knew the trim wasn't working - but who needs trim for a ten minute
every-which-way hop! I'm not one for flying level long, so we went into
a turning dive -somewhere over 140. All hell broke loose and I about
lost control . . . elevator flutter - it was violent! Honest, each wing
and the whole tail was shuddering.
I came off the power . . . leveled my wing . . . very hard to do, and
started looking for a place to dump her. About 90, the flutter slowed
but still bad - at 80 it quit!
I kept my head, let her glide for a few seconds and then added power -
kept my nose high and flew back to the airport but slow - making shallow
turns and a long straight in to a God awful landing - but safe!
Once on the ground I found the problem - the trim tab. Suddenly I
remembered. Earlier a boy and his dad were visiting with me while I was
working on my brakes. The boy was in back playing with the elevator. He
must have bent the tab control wire - leaving the tab to start
fluttering at high speed - thus causing the elevator to flutter.
It took two minutes to fix the cable. I checked for other damage - none.
She is an awful strong design, that Emeraude.
It took a little longer to get up enough guts to fly her again, but I
did the same day.
She's fine now but I have a little more respect for small items. I also
preflight a little more carefully now. I don't know if you have ever
experienced flutter or really know what it's like - I'm afraid of it now."
There are not too many folks around who can tell you, first hand, how
sudden and destructive control flutter can be. We do know it can happen
and does happen all too often. This gent was lucky. He had a good stout
airplane and did just the right thing.
--
KRnet mailing list
KRnet@list.krnet.org
https://list.krnet.org/mailman/listinfo/krnet
