Also look at /*ROUTE statement in JES2
Lizette > -----Original Message----- > From: IBM Mainframe Discussion List [mailto:[email protected]] On > Behalf Of Hardee, Chuck > Sent: Tuesday, November 11, 2014 6:55 AM > To: [email protected] > Subject: Re: SMP/E APPLY output capture question > > Thanks for the thought Lizette, but I did go down that path, but I found no way to > specify the OUTPUT= parameter in the SYSPRINT DDDEF. > > Do you have an idea of how I would accomplish that? > > C- > > Charles (Chuck) Hardee > Senior Systems Engineer/Database Administration EAS Information Technology > > Thermo Fisher Scientific > 300 Industry Drive | Pittsburgh, PA 15275 Phone +1 (724) 517-2633 | Mobile +1 > (412) 877-2809 | FAX: +1 (412) 490-9230 [email protected] | > www.thermofisher.com > > WORLDWIDE CONFIDENTIALITY NOTE: Dissemination, distribution or copying of > this e-mail or the information herein by anyone other than the intended recipient, or > an employee or agent of a system responsible for delivering the message to the > intended recipient, is prohibited. If you are not the intended recipient, please inform > the sender and delete all copies. > > > -----Original Message----- > From: IBM Mainframe Discussion List [mailto:[email protected]] On > Behalf Of Lizette Koehler > Sent: Tuesday, November 11, 2014 8:48 AM > To: [email protected] > Subject: Re: SMP/E APPLY output capture question > > See if the /*OUTPUT Jcl statement could help. > > Lizette > > > > -----Original Message----- > > From: IBM Mainframe Discussion List [mailto:[email protected]] > > On Behalf Of Hardee, Chuck > > Sent: Tuesday, November 11, 2014 6:35 AM > > To: [email protected] > > Subject: Re: SMP/E APPLY output capture question > > > > Thanks Christian, but I tried that already. > > I changed the utility to use the DD name ASMPRINT and then coded an > > ASMPRINT DD with SYSYOUT=* and when the APPLY was executed I received > > nothing via that DD, the usermod was not applied and I received no > > errors > indicating > > that there was a problem with the assembly or a problem in the APPLY. > > Very misleading. > > > > I will, however, try it again since you have indicated that it should > work. > > It is quite possible I did not have something quite right. > > > > I'll update again when I have further news. > > > > C- > > > > Charles (Chuck) Hardee > > Senior Systems Engineer/Database Administration EAS Information > > Technology > > > > Thermo Fisher Scientific > > 300 Industry Drive | Pittsburgh, PA 15275 Phone +1 (724) 517-2633 | > > Mobile > +1 > > (412) 877-2809 | FAX: +1 (412) 490-9230 [email protected] > > | www.thermofisher.com > > > > WORLDWIDE CONFIDENTIALITY NOTE: Dissemination, distribution or copying > > of this e-mail or the information herein by anyone other than the > > intended > recipient, or > > an employee or agent of a system responsible for delivering the > > message to > the > > intended recipient, is prohibited. If you are not the intended > > recipient, > please inform > > the sender and delete all copies. > > > > -----Original Message----- > > From: IBM Mainframe Discussion List [mailto:[email protected]] > > On Behalf Of Christian Birr > > Sent: Tuesday, November 11, 2014 8:27 AM > > To: [email protected] > > Subject: AW: SMP/E APPLY output capture question > > > > Chuck, > > in the SMP/E dialog select the global zone, under UTILITY select > > ASMA90 > (or what > > else you might use), specify a print DD name and use this in your JCL > > and > review > > the PARM statements. > > Christian > > -----Ursprüngliche Nachricht----- > > Von: IBM Mainframe Discussion List [mailto:[email protected]] > > Im Auftrag von Hardee, Chuck > > Gesendet: Dienstag, 11. November 2014 13:54 > > An: [email protected] > > Betreff: SMP/E APPLY output capture question > > > > Hello Listers, > > > > I am in need of capturing the output from an APPLY step, specifically > > the > assembly > > and link output. > > Currently my target zone has SYSPRINT defined as SYSOUT=*. > > I have tried several things but, unless I've coded them incorrectly, > > they > did not > > achieve the result I need. > > > > I have tried supplying a defining a OUTPUT statement at the start of > > my > job and > > then supplying a SYSPRINT DD with an OUTPUT= naming the OUTPUT > > statement's name. That didn't work, and I didn't get any indication > > from > SMP/E as to > > errors, but my usermod was not applied. > > > > I have tried defining the assembler utility as using an alternate > > SYSPRINT > DD and > > then supplying that DD and I don't get the assembly output via the new > > DD > name > > which I supplied in the JCL. In fact, I don't get any errors with that > setup either but > > the usermod did not apply in the arrangement either. > > > > Ultimately, what I want to accomplish it to have 2 copies of the output. > One to go to > > our production control department as part of the documentation filed > > when > locking > > down the source and the other to stay within our own library system so > that if we > > have issues with the program being controlled, we have quicker and > > easier > access > > to the current listing than we would if we had to go thru the > > production > control library. > > > > I can obtain the result I want, to a degree, if I manually change the > output class, > > form and destination as we have JES writers to handle it, but I'd > > rather > not have to > > remember to go and change the various JES attributes of the job if I > > can > do it in the > > JCL. > > > > If there is some way to cause SMP/E to spool its assembly and link > > steps > to VIO > > that would be great as I could then follow the APPLY step with an > > IEBGENER > and > > code SYSUT2 with the appropriate OUTPUT names and have the output > > handled as I want. > > > > Anyone have any ideas? > > > > Thanks, > > Chuck > > > > Charles (Chuck) Hardee > > Senior Systems Engineer/Database Administration EAS Information > > Technology > > > > Thermo Fisher Scientific > > 300 Industry Drive | Pittsburgh, PA 15275 Phone +1 (724) 517-2633 | > > Mobile > +1 > > (412) 877-2809 | FAX: +1 (412) 490-9230 [email protected] > > | www.thermofisher.com ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: INFO IBM-MAIN
