Hello,
Thanks to all. At last cheating z/OS solution worked and I
copied IEFBR14
as DFSMRCL0 into LPALIB and ipled.
Thanks once again.
On Sat, Jan 4, 2014 at 11:06 PM, Lizette Koehler <[email protected]>wrote:
> The message IEA303W is a warning message. I am not sure that would have
> stopped your IPL.
>
> You need to review all of the NIP messages to see what caused the issue.
> You should, I think, see them on the HMC Console. Or take a SAD dump and
> review the NIP Messages from another LPAR.
>
>
> If you can access the dasd for your new z/OS V2.1 system libraries, do as
> John suggested and copy IEFBR14 as DFSMRCL0 into LPALIB. Then IPL. If it
> still stops, this is not your issue.
>
> Create the DFSMRCL0 module by copying IEFBR14 and renaming it to DFSMRCL0
> and place in SYS1.LPALIB
>
>
> Lizette
>
>
> > -----Original Message-----
> > From: IBM Mainframe Discussion List [mailto:[email protected]] On
> > Behalf Of venkat kulkarni
> > Sent: Saturday, January 04, 2014 10:26 AM
> > To: [email protected]
> > Subject: Re: IPL Issue
> >
> > Hello,
> > Thanks for reply. We have many IMS version like V8,V9,V10. But
> as
> of now
> > no plan to run IMS on this system.
> >
> > But now issue is, how can I run RESTORE job. Because my system is not
> working
> > and not able to ipl and If I use another working system and try to
> restore, it will end
> > up removing entry from running system SYS1.LPALIB.
> >
> > So, can you please suggest alternate way to remove this and make system
> work.
> > Also I am not able to understand John's suggestion.
> >
> >
> >
> >
> >
> >
> > On Sat, Jan 4, 2014 at 10:48 PM, Lizette Koehler
> > <[email protected]>wrote:
> >
> > > If you are running IMS V9 or above you do not need to have the USERMOD.
> > >
> > > I would restore/reject the usermod. Then update your system and IPL.
> > >
> > > John's suggestion may work so long as you do not have IMS running at
> > > this time. However
> > >
> > > RESTORE/REJECT the usermod if your IMS is at V9 or above.
> > >
> > > Also, check out this information here as well The ZAP to add DFSMRCL0
> > > to IEAVTRML CSECT of IGC0001C used to be at offset 0000, but to make
> > > it work, we had to change the offset to 000C.
> > > ABEND806 RC4 occurred ...
> > >
> > > http://www-01.ibm.com/support/docview.wss?uid=swg21145559
> > >
> > >
> > > What version of IMS will you be running?????
> > >
> > >
> > > Lizette
> > >
> > >
> > > > -----Original Message-----
> > > > From: IBM Mainframe Discussion List
> > > > [mailto:[email protected]] On Behalf Of venkat kulkarni
> > > > Sent: Saturday, January 04, 2014 10:08 AM
> > > > To: [email protected]
> > > > Subject: Re: IPL Issue
> > > >
> > > > Hello,
> > > > Thanks for reply. As of now we don't have IMS on this new
> > > > system,
> > > but I just
> > > > applied USERMOD, as I mentioned in my previous email.
> > > >
> > > > And then I tried ipling system and getting this error.
> > > >
> > > > CSV003I REQUESTED MODULE DFSMRCL0 NOT FOUND
> > > >
> > > > IEA303W abend 806 REASON 0000004 during initialization under RIM
> > > > IEAVNPA1 DFSMRCL0
> > > > Module NOT FOUND.
> > > >
> > > >
> > > > What changes do I need to make, So that system can find this module
> > > > DFSMRCL0 and ipl can continue.
> > > >
> > > > We have IMS running in other system and our volumes and user
> > > > catalog are shared.
> > > >
> > > >
> > > >
> > > >
> > > > On Sat, Jan 4, 2014 at 10:32 PM, Lizette Koehler
> > > > <[email protected]>wrote:
> > > >
> > > > > I am not sure what version of IMS you are running.
> > > > >
> > > > > But this link for IMS V11 details how to remove the DFSMRCL0
> Module.
> > > > > It is not needed from IMS V9 and later versions.
> > > > >
> > > > >
> > > > > http://publib.boulder.ibm.com/infocenter/dzichelp/v2r2/index.jsp?t
> > > > > opic =%2Fco
> > > > > m.ibm.ims11.doc.sag%2Fsystem_admin%2Fims_uninstall_dfsmrclo.htm
> > > > >
> > > > > After you have completely migrated to IMST Version 9 or later and
> > > > > there is no possibility of running an earlier release of IMS (both
> > > > > IMS control and IMS batch jobs), you can remove DFSMRCL0 from the
> > > > > host
> > > z/OSR
> > > > system.
> > > > >
> > > > > To remove DFSMRCL0 from the host z/OS system, perform the
> > > > > following
> > > steps:
> > > > >
> > > > > Remove the name DFSMRCL0 from the IEAVTRML CSECT of module
> > > > > IGC0001C in SYS1.LPALIB. Removing this name prevents the operating
> > > > > system from installing DFSMRCL0 as a Static Resource Cleanup
> > > > > routine at
> > > the
> > > > next IPL.
> > > > > Remove module DFSMRCL0 from SYS1.LPALIB or the MLPA library
> > > > > where
> > > > > DFSMRCL0 was bound.
> > > > > Restart with CLPA to enable these changes.
> > > > >
> > > > > Lizette
> > > > >
> > > > >
> > > > > > -----Original Message-----
> > > > > > From: IBM Mainframe Discussion List
> > > > > > [mailto:[email protected]] On Behalf Of venkat kulkarni
> > > > > > Sent: Saturday, January 04, 2014 9:24 AM
> > > > > > To: [email protected]
> > > > > > Subject: IPL Issue
> > > > > >
> > > > > > Hello,
> > > > > > I applied USERMOD in my new z/OS 2.1 system and then
> > > > > > ipled
> > > > > system
> > > > > but
> > > > > > getting below issue.
> > > > > >
> > > > > > CSV003I REQUESTED MODULE DFSMRCL0 NOT FOUND
> > > > > >
> > > > > > IEA303W abend 806 REASON 0000004 during initialization under RIM
> > > > > > IEAVNPA1
> > > > > > DFSMRCL0 Module NOT FOUND.
> > > > > >
> > > > > >
> > > > > > and the usermod I applied was
> > > > > >
> > > > > > //SMPPTFIN DD DATA,DLM='%%'
> > > > > > ++USERMOD(USRMOD01) REWORK(2013035) .
> > > > > > ++VER(Z038) FMID(HBB7790) .
> > > > > > ++SRC(IEAVTRML) DISTLIB(AOSC5) .
> > > > > > IEAVTRML CSECT
> > > > > > DC CL8'ERBMFRES' RMF
> > > > > > DC F'0'
> > > > > > DC CL8'MVPTTRML' TCP/IP
> > > > > > DC F'0'
> > > > > > DC CL8'DFSMRCL0' IMS
> > > > > > DC F'0'
> > > > > > DC F'0'
> > > > > > DC F'0'
> > > > > > DC F'0'
> > > > > > END
> > > > > > %%
> > > > > > //
> > > > > >
> > > > > > As this is newly build system, so it doesn't have IMS yet.
> > > > > > I can follow below link to remove DFSMRCL0 from IGC0001C but
> > > > > > not sure,
> > > > > if its
> > > > > > correct way of recovering from this issue.
> > > > > >
> > > > > >
> > > > >
> > > > > http://publib.boulder.ibm.com/infocenter/dzichelp/v2r2/index.jsp?t
> > > > > opic
> > > > > =%2Fco
> > > > > m.ibm
> > > > > > .ims11.doc.sag%2Fsystem_admin%2Fims_uninstall_dfsmrclo.htm
> > > > > >
> > > > > > Then I run AMASPZAP utility from the working system and pointed
> > > > > > the downsystem LPALIB volume to dump the current contents of
> > > > > > IEAVTRML as
> > > > > below
> > > > > > //DMPVTRML JOB
> > 'VENKAT',CLASS=A,MSGCLASS=A,NOTIFY=&SYSUID
> > > > > > //STEP001 EXEC PGM=AMASPZAP
> > > > > > //SYSLIB DD
> > > > DSN=SYS1.LPALIB,DISP=SHR,VOL=SER=ZS11T1,UNIT=3390
> > > > > > //SYSPRINT DD SYSOUT=A
> > > > > > //SYSIN DD *
> > > > > > DUMP IGC0001C IEAVTRML
> > > > > > /*
> > > > > >
> > > > > > and output is below .
> > > > > >
> > > > > >
> > > > > > **CCHHR- 1DA9000D01 RECORD LENGTH- 000E68 MEMBER
> > NAME
> > > > > > IGC0001C
> > > > > > CSECT NAME IEAVTRML
> > > > > > 000000 C5D9C2D4 C6D9C5E2 00000000 D4E5D7E3 E3D9D4D3
> > > > > > 00000000
> > > > > > C4C6E2D4 D9C3D3F0
> > > > > > 000020 00000000 00000000 00000000 00000000
> > > > > > AMA113I COMPLETED DUMP REQUIREMENTS
> > > > > >
> > > > > > AMA100I AMASPZAP PROCESSING COMPLETED
> > > > > >
> > > > > > I also tried setting up AMASPZAP utility to replace the entry
> > > > > > containing
> > > > > > DFSMRCL0 with zeros as below
> > > > > >
> > > > > >
> > > > > > //DMPVTRML JOB
> > 'VENKAT',CLASS=A,MSGCLASS=A,NOTIFY=&SYSUID
> > > > > > //STEP001 EXEC PGM=AMASPZAP
> > > > > > //SYSLIB DD
> > > > DSN=SYS1.LPALIB,DISP=SHR,VOL=SER=ZS11T1,UNIT=3390
> > > > > > //SYSPRINT DD SYSOUT=A
> > > > > > //SYSIN DD *
> > > > > > NAME IGC0001C IEAVTRML
> > > > > > VER 0000 C5D9C2D4C6D9C5E2
> > > > > > VER 000C D4E5D7E3E3D9D4D3
> > > > > > VER 0018 C4C6E2D4D9C3D3F0
> > > > > > REP 0000 D4E5D7E3E3D9D4D3
> > > > > > REP 000C C3C1D9F2D9E2C3F0
> > > > > > REP 0018 0000000000000000
> > > > > > /*
> > > > > >
> > > > > > But I feel this JCL is not fully correct, as I just used sample
> > > > > > available
> > > > > in IBM manual,
> > > > > > can body help me to resolve this issue.
> > > > > >
> > > > > > Also not able to find reason of IEA303W abend 806 REASON 0000004
> > > > > > during initialization under RIM IEAVNPA1 ---- This module
> > > > > > available in
> > > > > SYS.NUCLEUS
> > > > > >
> > >
> > > ----------------------------------------------------------------------
> > > For IBM-MAIN subscribe / signoff / archive access instructions, send
> > > email to [email protected] with the message: INFO IBM-MAIN
> > >
> >
> > ----------------------------------------------------------------------
> > For IBM-MAIN subscribe / signoff / archive access instructions, send
> email
> to
> > [email protected] with the message: INFO IBM-MAIN
>
> ----------------------------------------------------------------------
> For IBM-MAIN subscribe / signoff / archive access instructions,
> send email to [email protected] with the message: INFO IBM-MAIN
>
----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to [email protected] with the message: INFO IBM-MAIN
