Those are all good suggestions! I've edited the control points quite a bit to get the goldilocks level of mismatching - not too much, not too little - to the point where I'm very happy with the result, but I'm still not having any luck getting a stitch in the manner I'm after. I'll try the remapped image option next. Is there no way to turn off enblend/enfuse?
On Sat, Nov 11, 2023 at 2:07 PM David W. Jones <[email protected]> wrote: > Thanks. I've made panoramas using GIMP, never with Photoshop. > > An option that might work for you is to have Hugin output remapped images. > They'll be appropriately distorted, rotated, positioned as they would be in > a blended panorama. Then you can layer them together in Photoshop. I think > that would give you unblended seams. Simply flattening the layered image > might be sufficient. > > I haven't done that in a long time, so I forget if the remapped images > make transparent all parts of a remapped image that aren't included in the > blended panorama. But it might work. > > Another option, since you want deliberate mismatches and misalignments, is > to put in mismatched/bad control points. If you don't run the "clean > control points" option, the "bad" control points will survive and affect > the alignment process. > > I use Hugin with the Expert user interface, ("Interface > Expert"). If you > usually use the Simple interface or the Assistant tab in the GL Preview > window, you might need to change. The Expert interface gives a lot more > control over the process. > > On 11/10/23 04:49, Alexander Drecun wrote: > > Mostly with Photoshop or Affinity. I used Hugin and, with a basic > start-to-finish approach, have gotten very nice panoramas too. The issue > I’m having is that I’m deliberately trying to produce > bad/misaligned/unblended panoramas, and this can be difficult to > systematize. Photoshop will produce tiled, unblended results but only if I > overwhelm it to a very specific degree; if I add too many images, it will > freeze and won’t spit anything out. Affinity, meanwhile, always blends no > matter the result it gets. I think Hugin is the best option is because I > can make choices about all of the control points that decide just how > aligned or misaligned my panoramas are. The issue is that I just need to > figure out how to prevent it from trying to blend the component images into > a seamless stitch. > > > > On Nov 9, 2023, at 11:11 PM, David W. Jones <[email protected]> > <[email protected]> wrote: > > How do you make your panoramas now? > > On 11/9/23 20:47, Alexander Drecun wrote: > > <Screenshot 2023-11-09 at 10.45.00 PM.png> > <Screenshot 2023-11-09 at 10.46.33 PM.png> > Yeah, a hard cut. I'm aiming for a stitch that is basically the tiled > images layered over one another before any blending or exposure correction > is done. I've attached a screencap from the preview window and a screencap > of what it's looking like once stitched. (Btw it's intentional that things > are misaligned.) > > I'll try these entries with Enblend to see if they make a difference. How > do I leave out "photometric optimization?" I'm still relatively new to > Hugin and so some of these things are a bit over my head. > > Thanks, > > Alex > > On Thu, Nov 9, 2023 at 6:13 PM David W. Jones <[email protected]> > wrote: > >> Hmm, so you want hard seams between images - no blending, just a sharp >> cut from one image to the next? >> >> Gunter's reference to the online documentation might have the solution >> in it. >> >> Maybe one option is to set enblend's levels to 1? I think "--levels=1" >> tells enblend tto blend as little as possible between images. >> >> On 11/8/23 20:07, Alexander Drecun wrote: >> > Is there any way to stitch a panorama without having Hugin blend/match >> > the exposure across the component images? Specifically, I want to see >> > the seams and edges of each component image in the stitched panorama. >> > >> > Thanks, >> > >> > Alex > > > -- > David W. [email protected] > wandering the landscape of godhttp://dancingtreefrog.com > My password is the last 8 digits of π. > > -- > A list of frequently asked questions is available at: > http://wiki.panotools.org/Hugin_FAQ > --- > You received this message because you are subscribed to the Google Groups > "hugin and other free panoramic software" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/hugin-ptx/8417189b-e313-4dd3-9319-837a1125644c%40gmail.com > <https://groups.google.com/d/msgid/hugin-ptx/8417189b-e313-4dd3-9319-837a1125644c%40gmail.com?utm_medium=email&utm_source=footer> > . > -- A list of frequently asked questions is available at: http://wiki.panotools.org/Hugin_FAQ --- You received this message because you are subscribed to the Google Groups "hugin and other free panoramic software" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/hugin-ptx/CABqZK5e8Hx6dJfRLQhO5pk3ZG_1%2BvLyStnpf-dN%3DHUQqhFZ_Xg%40mail.gmail.com.
