Thanks for your interest: this is what appears when I load my ethernet packet driver:
_2 DRIVE(S) AVAILABLE. _ _NOVELL LINK SUPPORT LAYER FOR DOS ODI V2.20 (960401) _ _(C) COPYRIGHT 1990 - 1996, BY NOVELL, INC. ALL RIGHTS RESERVED. _ _BUFFERS 6 1600 _ _THE CONFIGURATION FILE USED WAS "C:BROADCOMB44NET.CFG". _ _MAX BOARDS 4, MAX STACKS 4 _ _BUFFERS 6, BUFFER SIZE 1600 BYTES, MEMORY POOL 0 BYTES. _ _BROADCOM 440X 10/100 INTEGRATED CONTROLLER DOS ODI DRIVER V3.11 (050908) _ _COPYRIGHT (C) 2000-2005, BROADCOM CORPORATION. ALL RIGHTS RESERVED. _ _DEVICE - BROADCOM 440X 10/100 INTEGRATED CONTROLLER, MAC ADDRESS - 00C09F48F4DF_ _LINESPEED - 100MBPS FULLDUPLEX, IRQ - 6, BUSNUM - 2, DEVNUM - 2 _ _BOARD 1, FRAME ETHERNET_II, LSB MODE _ _ODIPKT 3.1 _ _(C) COPYRIGHT DANIEL LANCIANI 1991-1996. ALL RIGHTS RESERVED. _ _THIS SOFTWARE IS PROVIDED WITH NO WARRANTY. _ _USING ETHERNET FRAMING, CLASS 1 _ _REGISTERED AS HIGH PRIORITY CHAINED DEFAULT STACK _ _ODIPKT IS INSTALLED AND READY._ All right. it works. This is what happens when I "add" fdnet bat: _PACKET DRIVER SKELETON COPYRIGHT 1988-93, CRYNWR SOFTWARE. _ _THIS PROGRAM IS FREELY COPYABLE; SOURCE MUST BE AVAILABLE; NO WARRANTY. _ _SEE THE FILE COPYING.DOC FOR DETAILS; SEND FAX TO +1-315-268-9201 FOR A COPY. _ _SYSTEM: [345]86 PROCESSOR, ISA BUS, TWO 8259S _ _PACKET DRIVER SOFTWARE INTERRUPT IS 0X60 (96) _ _INTERRUPT NUMBER 0X5 (5) _ _I/O PORT 0X300 (768) _ _MY ETHERNET ADDRESS IS FF:FF:FF:FF:FF:FF _ _MTCP DHCP CLIENT BY M BRUTMAN (mbbrut...@gmail.com) (C)OPYRIGHT 2008-2013 _ _ VERSION: MAY 23 2013 _ _TIMEOUT PER REQUEST: 10 SECONDS, RETRY ATTEMPTS: 3 _ _SENDING DHCP REQUESTS, PRESS [ESC] TO ABORT. _ _DHCP REQUEST SENT, ATTEMPT 1: TIMEOUT _ _DHCP REQUEST SENT, ATTEMPT 2: TIMEOUT _ _DHCP REQUEST SENT, ATTEMPT 3: TIMEOUT _ _ERROR: YOUR ETHERNET CARD REPORTED AN ERROR FOR EVERY PACKET WE SENT. _ _CHECK YOUR CABLING AND PACKET DRIVER SETTINGS._ It is clear that ther's a conflict, (and I don't know what it is) but other than that I am doubtful that fdnet .bat is useful for those who only use freedos and not vb. regards, andrea Il 15.03.2021 12:32 Dean Galloway ha scritto: > Hello Andrea, > > Perhaps you can post some screenshots of the messages you are receiving when the packet driver loads? > > Thanks, > Dean. > On 3/15/2021 12:28 AM, andrea...@tiscali.it [4] wrote: > >> HI AT ALL >> IN FREEDOS1.3 THERE IS IN C:/FDOS/BIN THE PROGRAM FDNET.BAT. OK: WIKI.FREDOS.ORG EXPLAINS THAT IT IS A PROGRAM FOR VIRTUALBOX, AND THAT IN CASE YOU HAVE A FREEDOS WITHOUT VIRTUALBOX YOU HAVE TO WRITE A LINE FIRST WITH YOUR ETHERNET PACKET DRIVER. >> Well, i don't have virtualbox and i don't understand why i have to load my packet driver in autoexec.bat (or fdauto, bat.) I prefer to load and unload it according to memory needs, time by time. >> Good. however i tried to add my packet driver to my autoexet.bat right before on the line produced by fdnet.bat . >> It don't work. >> Responds: _dhcp request send:error, your ethernet card report an error for every packet sent.Check your cablin ecc...._ >> and my Ethernet card driver don't work too; then I've to delete all the last line on my autoexec.bat ( and reload my ethernet packet driver)to go on line. >> >> ANDREA >> >> Con Tiscali Mobile Smart 30 4G hai minuti illimitati, 100 SMS e 30 Giga in 4G a soli 8,99EUR al mese. http://tisca.li/smart30 [1] >> >> _______________________________________________ >> Freedos-user mailing list >> Freedos-user@lists.sourceforge.net [2] >> https://lists.sourceforge.net/lists/listinfo/freedos-user [3] Con Tiscali Mobile Smart 30 4G hai minuti illimitati, 100 SMS e 30 Giga in 4G a soli 8,99€ al mese. http://tisca.li/smart30
_______________________________________________ Freedos-user mailing list Freedos-user@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/freedos-user
