Thanks Jonathan,
I'm starting to expect it has to be the controller as well. About 20
minutes after I posted this message yesterday (and thus 20 minutes
after ad6 got disconnected - atacontrol list showed "no device
present" for it) the machine crashed while writing to the remaining
ad4 drive (kernel panic). I attached the logs below. I also ran the
long smart self test on both drives, and no errors were found on
either drive (logs also attached).
Unfortunately I could not attach the new disks to my mainboard SATA
because my mainboard SATA somehow hangs trying to detect them. So I
cannot test if *not* using the controller is going to solve the
problems, though I'm it seems logical at the moment it has to be the
controller, especially if other people have had similar issues.
I guess I'll be buying another controller.
Regards,
Sebastiaan
Jonathan Groll wrote:
On Wed, Aug 13, 2008 at 03:10:56PM +0200, Sebastiaan van Erk wrote:
Hi,
Just an update on this issue.
Quick summary: I fixed the BIOS issues, the hardware monitor
issues, and the rl0/rl1 watchdog timeout issues (it seems).
However I'm still having problems with my SATA drives (or at least
one of them). More info below.
BIOS:
I flashed my BIOS to the latest version about a year ago, and
never noticed that there was any problem, but it turns out there
was. I never reset the BIOS to default factory settings after the
upgrade, and it seems the settings were corrupt. After having
reset the BIOS to the "default optimized factory settings" it
stopped crashing when I go into the H/W monitor and also when
using healthd -d (output below):
Temp.= 40.0, 36.0, 66.0; Rot.= 0, 0, 0
Vcore = 1.44, 3.12; Volt. = 3.34, 5.00, 1.95, -0.11, -1.54
Temp.= 40.0, 36.0, 66.0; Rot.= 0, 0, 0
Vcore = 1.44, 3.14; Volt. = 3.33, 4.97, 1.95, -0.11, -1.54
Temp.= 40.0, 36.0, 66.0; Rot.= 0, 0, 0
Vcore = 1.44, 3.12; Volt. = 3.34, 4.97, 1.95, -0.11, -1.54
Temp.= 40.0, 36.0, 66.0; Rot.= 0, 0, 0
Vcore = 1.44, 3.12; Volt. = 3.34, 5.00, 1.95, -0.11, -1.54
Temp.= 40.0, 36.0, 66.0; Rot.= 0, 0, 0
Vcore = 1.44, 3.12; Volt. = 3.34, 5.00, 1.95, -0.11, -1.54
This also seems to have fixed the rl0 watchdog timeout problems. I
no longer see those in my logs.
SATA DRIVES:
I'm still having problems with the SATA drives.
I tried connecting the 1TB Samsung drives to my mainboard, but
then the box hangs when booting with the "Detecting IDE drives"
message. The regular (PATA) IDE drives are detected first, and
then it repeats the "Detecting IDE drives" message to detect the
sata drives, and hangs. When I connect my 250GB SATA drives to my
mainboard they detect fine, and the box boots normally.
I did another rsync of my old mirror (the 250GB disks) to the new
mirror (1TB disks), but again one of the disks got detached. This
time there are no other messages in the log, the only thing I see
is the following:
Aug 13 14:35:27 piglet su: sebster to root on /dev/ttyp5
Aug 13 14:55:38 piglet kernel: ad6: FAILURE - device detached
Aug 13 14:55:38 piglet kernel: subdisk6: detached
Aug 13 14:55:38 piglet kernel: ad6: detached
Aug 13 14:55:38 piglet kernel: GEOM_MIRROR: Device gm1: provider
ad6 disconnected.
Aug 13 15:00:00 piglet newsyslog[1800]: logfile turned over due to
size>100K
(unfortunate that the log file just got rotated, but in the new
log file there is nothing execpt the one expected line:
Aug 13 15:00:00 piglet newsyslog[1800]: logfile turned over due to
size>100K
So, nothing after the disconnect...
The questions I have now is:
1) Could an upgrade to FreeBSD 7-STABLE fix the issue (it's a LOT
of work for me, but I'll do it if there are SATA driver issues
fixed).
I suspect the problem may be the SiI driver in Freebsd. As a
reference
point, I've had a similar problem, even on 7-STABLE, but with sparc64
hardware (see earlier post in this thread).
It'll probably be simplest for you to just buy another controller of
another brand. On the other hand, it'll be worth knowing exactly what
is wrong with the SiI driver...
Cheers,
Jonathan
Aug 13 15:00:00 piglet newsyslog[1800]: logfile turned over due to
size>100K
Aug 13 15:11:26 piglet su: sebster to root on /dev/ttyp4
Aug 13 15:34:55 piglet kernel: mirror/
gm1s1e[WRITE(offset=875450693632, length=2048)]error = 6
Aug 13 15:34:55 piglet kernel: g_vfs_done():mirror/
gm1s1e[WRITE(offset=875450695680, length=2048)]error = 6
[snip 335750 similar lines]
Aug 13 15:36:30 piglet kernel: g_vfs_done():mirror/
gm1s1e[WRITE(offset=875450931200, length=2048)]error = 6
Aug 13 15:36:30 piglet kernel: g_vfs_done():mirror/
gm1s1e[WRITE(offset=875450933248, length=2048)]error = 6
Aug 13 15:36:30 piglet kernel: g_vfs_done():mirror/
gm1s1e[WRITE(offset=875450935296, length=2048)]error = 6
Aug 13 15:36:30 piglet kernel: g_vfs_done():mirror/
gm1s1e[WRITE(offset=875450937344, length=2048)]error = 6
Aug 13 15:36:30 piglet kernel: g_vfs_done():mirror/
gm1s1e[WRITE(offset=875450939392, length=2048)]error = 6
Aug 13 15:36:30 piglet kernel: g_vfs_done():mirror/
gm1s1e[WRITE(offset=875450941440, length=2048)]error = 6
Aug 13 15:36:30 piglet kernel: g_vfs_done():mirror/
gm1s1e[WRITE(offset=875450943488, length=2048)]error = 6
Aug 13 15:36:30 piglet kernel: g_vfs_done():mirror/
gm1s1e[WRITE(offset=875450945536, length=2048)]error = 6
Aug 13 15:36:30 piglet kernel: g_vfs_done():mirror/
gm1s1e[WRITE(offset=875450947584, length=2048)]error = 6
Aug 13 15:36:30 piglet kernel: g_vfs_done():mirror/
gm1s1e[WRITE(offset=875450949632, length=2048)]error = 6
Aug 13 15:36:30 piglet kernel: g_vfs_done():mirror/
gm1s1e[WRITE(offset=875450951680, length=2048)]error = 6
Aug 13 15:36:30 piglet kernel: g_vfs_done():mirror/
gm1s1e[WRITE(offset=875450953728, length=2048)]error = 6
Aug 13 15:36:30 piglet kernel: g_vfs_done():mirror/
gm1s1e[WRITE(offset=875450955776, length=2048)]error = 6
Aug 13 15:36:30 piglet kernel: g_vfs_done():mirror/
gm1s1e[WRITE(offset=875450957824, length=2048)]error = 6
Aug 13 15:36:30 piglet kernel: g_vfs_done():mirror/
gm1s1e[WRITE(offset=875450959872, length=2048)]error = 6
Aug 13 15:36:30 piglet kernel: g_vfs_done():mirror/
gm1s1e[WRITE(offset=875450961920, length=2048)]error = 6
Aug 13 15:36:30 piglet kernel: g_vfs_done():mirror/
gm1s1e[WRITE(offset=875450963968, length=2048)]error = 6
Aug 13 15:36:30 piglet kernel: g_vfs_done():mirror/
gm1s1e[WRITE(offset=875450966016, length=2048)]error = 6
Aug 13 15:36:30 piglet kernel: g_vfs_done():mirror/
gm1s1e[WRITE(offset=875450968064, length=2048)]error = 6
Aug 13 15:36:30 piglet kernel: g_vfs_done():mirror/
gm1s1e[WRITE(offset=875450970112, length=2048)]error = 6
Aug 13 15:36:30 piglet kernel: g_vfs_done():mirror/
gm1s1e[WRITE(offset=875450972160, length=2048)]error = 6
Aug 13 15:36:30 piglet kernel: g_vfs_done():mirror/
gm1s1e[WRITE(offset=875450974208, length=2048)]error = 6
Aug 13 15:42:23 piglet syslogd: kernel boot file is /boot/kernel/
kernel
Aug 13 15:42:23 piglet kernel: Copyright (c) 1992-2008 The FreeBSD
Project.
smartctl version 5.38 [i386-portbld-freebsd6.3] Copyright (C) 2002-8
Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: SAMSUNG HD103UJ
Serial Number: S13PJ1BQ606865
Firmware Version: 1AA01112
User Capacity: 1,000,204,886,016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 3b
Local Time is: Thu Aug 14 11:28:13 2008 CEST
==> WARNING: May need -F samsung or -F samsung2 enabled; see manual
for details.
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x02) Offline data collection
activity
was completed without error.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test
routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (11811) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before
entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 198) minutes.
Conveyance self-test routine
recommended polling time: ( 21) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail
Always - 0
3 Spin_Up_Time 0x0007 076 076 011 Pre-fail
Always - 8010
4 Start_Stop_Count 0x0032 100 100 000 Old_age
Always - 8
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000f 253 253 051 Pre-fail
Always - 0
8 Seek_Time_Performance 0x0025 100 100 015 Pre-fail
Offline - 10255
9 Power_On_Hours 0x0032 100 100 000 Old_age
Always - 272
10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail
Always - 0
11 Calibration_Retry_Count 0x0012 100 100 000 Old_age
Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age
Always - 8
13 Read_Soft_Error_Rate 0x000e 100 100 000 Old_age
Always - 0
183 Unknown_Attribute 0x0032 100 100 000 Old_age
Always - 0
184 Unknown_Attribute 0x0033 100 100 099 Pre-fail
Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age
Always - 0
188 Unknown_Attribute 0x0032 100 100 000 Old_age
Always - 0
190 Airflow_Temperature_Cel 0x0022 057 052 000 Old_age
Always - 43 (Lifetime Min/Max 43/48)
194 Temperature_Celsius 0x0022 056 050 000 Old_age
Always - 44 (Lifetime Min/Max 43/50)
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age
Always - 195799724
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age
Always - 0
197 Current_Pending_Sector 0x0012 100 100 000 Old_age
Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x003e 100 100 000 Old_age
Always - 0
200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age
Always - 0
201 Soft_Read_Error_Rate 0x000a 100 100 000 Old_age
Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 0
Warning: ATA Specification requires self-test log structure revision
number = 1
Num Test_Description Status Remaining
LifeTime(hours) LBA_of_first_error
# 1 Offline Completed without error 00%
261 -
# 2 Offline Aborted by host 40%
251 -
# 3 Short offline Aborted by host 00%
250 -
SMART Selective Self-Test Log Data Structure Revision Number (0)
should be 1
SMART Selective self-test log data structure revision number 0
Warning: ATA Specification requires selective self-test log data
structure revision number = 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute
delay.
smartctl version 5.38 [i386-portbld-freebsd6.3] Copyright (C) 2002-8
Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: SAMSUNG HD103UJ
Serial Number: S13PJ1BQ607102
Firmware Version: 1AA01112
User Capacity: 1,000,204,886,016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 3b
Local Time is: Thu Aug 14 11:28:39 2008 CEST
==> WARNING: May need -F samsung or -F samsung2 enabled; see manual
for details.
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x02) Offline data collection
activity
was completed without error.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test
routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (12131) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before
entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 203) minutes.
Conveyance self-test routine
recommended polling time: ( 22) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail
Always - 0
3 Spin_Up_Time 0x0007 077 077 011 Pre-fail
Always - 7810
4 Start_Stop_Count 0x0032 100 100 000 Old_age
Always - 10
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000f 253 253 051 Pre-fail
Always - 0
8 Seek_Time_Performance 0x0025 100 100 015 Pre-fail
Offline - 9978
9 Power_On_Hours 0x0032 100 100 000 Old_age
Always - 272
10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail
Always - 0
11 Calibration_Retry_Count 0x0012 100 100 000 Old_age
Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age
Always - 10
13 Read_Soft_Error_Rate 0x000e 100 100 000 Old_age
Always - 0
183 Unknown_Attribute 0x0032 100 100 000 Old_age
Always - 0
184 Unknown_Attribute 0x0033 100 100 099 Pre-fail
Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age
Always - 0
188 Unknown_Attribute 0x0032 100 100 000 Old_age
Always - 0
190 Airflow_Temperature_Cel 0x0022 059 054 000 Old_age
Always - 41 (Lifetime Min/Max 41/46)
194 Temperature_Celsius 0x0022 058 053 000 Old_age
Always - 42 (Lifetime Min/Max 41/47)
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age
Always - 31616
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age
Always - 0
197 Current_Pending_Sector 0x0012 100 100 000 Old_age
Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x003e 100 100 000 Old_age
Always - 0
200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age
Always - 0
201 Soft_Read_Error_Rate 0x000a 100 100 000 Old_age
Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 0
Warning: ATA Specification requires self-test log structure revision
number = 1
Num Test_Description Status Remaining
LifeTime(hours) LBA_of_first_error
# 1 Offline Completed without error 00%
261 -
# 2 Offline Aborted by host 40%
251 -
# 3 Short offline Aborted by host 00%
250 -
SMART Selective Self-Test Log Data Structure Revision Number (0)
should be 1
SMART Selective self-test log data structure revision number 0
Warning: ATA Specification requires selective self-test log data
structure revision number = 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute
delay.