On Fri, Sep 21, 2012 at 3:11 PM, Mike Tancsa <m...@sentex.net> wrote: > On 9/21/2012 4:59 PM, Jim Harris wrote:
<snip> > Thanks, that allows it to boot up now! > > pci2: <ACPI PCI bus> on pcib2 > LSI 3ware device driver for SAS/SATA storage controllers, version: > 10.80.00.003 > tws0: <LSI 3ware SAS/SATA Storage Controller> port 0x4000-0x40ff mem > 0xc2460000-0xc2463fff,0xc2400000-0xc243ffff irq 17 at device 0.0 on pci2 > tws0: Using MSI > tws0: Controller details: Model 9750-4i, 8 Phys, Firmware FH9X > 5.12.00.007, BIOS BE9X 5.11.00.006 > em0: <Intel(R) PRO/1000 Network Connection 7.3.2> port 0x5040-0x505f mem > 0xc2500000-0xc251ffff,0xc2570000-0xc2570fff irq 19 at device 25.0 on pci0 > . > then a lot of > . > (probe65:tws0:0:65:0): INQUIRY. CDB: 12 0 0 0 24 0 > (probe65:tws0:0:65:0): CAM status: Invalid Target ID > (probe65:tws0:0:65:0): Error 22, Unretryable error > (probe1:tws0:0:1:0): INQUIRY. CDB: 12 0 0 0 24 0 > (probe1:tws0:0:1:0): CAM status: Invalid Target ID > (probe1:tws0:0:1:0): Error 22, Unretryable error > (probe2:tws0:0:2:0): INQUIRY. CDB: 12 0 0 0 24 0 > (probe2:tws0:0:2:0): CAM status: Invalid Target ID > . > . > . > (probe63:tws0:0:63:0): INQUIRY. CDB: 12 0 0 0 24 0 > (probe63:tws0:0:63:0): CAM status: Invalid Target ID > (probe63:tws0:0:63:0): Error 22, Unretryable error > (probe64:tws0:0:64:0): INQUIRY. CDB: 12 0 0 0 24 0 > (probe64:tws0:0:64:0): CAM status: Invalid Target ID > (probe64:tws0:0:64:0): Error 22, Unretryable error These can be ignored. CAM is just telling you that there are no devices attached at these target IDs. > da0 at tws0 bus 0 scbus0 target 0 lun 0 > da0: <LSI 9750-4i DISK 5.12> Fixed Direct Access SCSI-5 device > da0: 6000.000MB/s transfers > da0: 953654MB (1953083392 512 byte sectors: 255H 63S/T 121573C) > SMP: AP CPU #1 Launched! > SMP: AP CPU #4 Launched! > <snip> > > Any thoughts on msi vs no msi ? Time to run some stress tests. Its > certainly a fast little controller for the money! > Typically MSI is preferred to INTx for performance reasons. I can't speak for why the original author made INTx the default though. Regards, -Jim _______________________________________________ freebsd-stable@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-stable To unsubscribe, send any mail to "freebsd-stable-unsubscr...@freebsd.org"
