Running into the following: Jan 2 16:46:17 iPaq kernel: swap_pager: I/O error - pageout failed; blkno 4592,size 4096, error 5 Jan 2 16:46:17 iPaq kernel: swap_pager: I/O error - pageout failed; blkno 5200,size 8192, error 5 Jan 2 16:46:17 iPaq kernel: swap_pager: I/O error - pageout failed; blkno 11520,size 20480, error 5 Jan 2 16:46:17 iPaq kernel: swap_pager: I/O error - pageout failed; blkno 11904,size 65536, error 5
and Jan 2 18:49:53 iPaq kernel: spec_getpages:(da0s1a) I/O read failure: (error=5) bp 0xc1c94020 vp 0xc11d7000 Jan 2 18:49:53 iPaq kernel: size: 61440, resid: 61440, a_count: 61440, valid: 0x0 Jan 2 18:49:53 iPaq kernel: nread: 0, reqpage: 6, pindex: 92, pcount: 15 Jan 2 18:49:53 iPaq kernel: vm_fault: pager read error, pid 16022 (ld) Jan 2 18:49:53 iPaq kernel: umass0: Phase Error, residue = 16384 Jan 2 18:49:53 iPaq kernel: pid 16022 (ld), uid 0: exited on signal 11 (core dumped) Jan 2 18:49:54 iPaq kernel: swap_pager: I/O error - pagein failed; blkno 13456,size 36864, error 5 Jan 2 18:49:54 iPaq kernel: vm_fault: pager read error, pid 11988 (make) Jan 2 18:49:54 iPaq kernel: umass0: Phase Error, residue = 16384 Jan 2 18:49:55 iPaq kernel: pid 11988 (make), uid 0: exited on signal 11 (core dumped) Jan 2 18:49:56 iPaq kernel: spec_getpages:(da0s1a) I/O read failure: (error=5) bp 0xc1c94020 vp 0xc11d7000 Jan 2 18:49:56 iPaq kernel: size: 65536, resid: 65536, a_count: 65536, valid: 0x0 Jan 2 18:49:56 iPaq kernel: nread: 0, reqpage: 7, pindex: 24, pcount: 16 Jan 2 18:49:56 iPaq kernel: vm_fault: pager read error, pid 437 (csh) iPaq# usbdevs -v Controller /dev/usb0: addr 1: full speed, self powered, config 1, UHCI root hub(0x0000), VIA(0x0000), rev 1.00 port 1 powered port 2 addr 2: full speed, self powered, config 2, USB 2.0 Storage Adaptor(0xb001), DMI(0x0c0b), rev 11.10 Controller /dev/usb1: addr 1: full speed, self powered, config 1, UHCI root hub(0x0000), VIA(0x0000), rev 1.00 port 1 powered port 2 addr 2: full speed, power 156 mA, config 1, LINKSYS USB Adapter(0x400b), LINKSYS Inc.(0x066b), rev 1.01 Suggestions on how to debug or reduce the errors? The drive has good media (hooked direct to IDE it tests clean using Quantum's diag util) and the system will boot fine with a warm reboot of the comp itself, so I'm guessing the problem is driver related and not a fault with the HW. Joshua Coombs [EMAIL PROTECTED] To Unsubscribe: send mail to [EMAIL PROTECTED] with "unsubscribe freebsd-questions" in the body of the message
