On 03/24/2017 16:07, Caraballo-vega, Jordan A. (GSFC-6062)[COMPUTER
SCIENCE CORP] wrote:
At the time of implementing the vcxl* interfaces we get very bad results.
You're probably not using netmap with the vcxl interfaces, and the
number of "normal" tx and rx queues is just 2 for these interfaces.
Even if you _are_ using netmap, the hw.cxgbe.nnmtxq10g/rxq10g tunables
don't work anymore. Use these to control the number of queues for netmap:
hw.cxgbe.nnmtxq_vi
hw.cxgbe.nnmrxq_vi
You should see a line like this in dmesg for all cxl/vcxl interfaces and
that tells you exactly how many queues the driver configured:
cxl0: 4 txq, 4 rxq (NIC); 4 txq, 2 rxq (TOE)
packets errs idrops bytes packets errs bytes colls drops
629k 4.5k 0 66M 629k 0 66M 0 0
701k 5.0k 0 74M 701k 0 74M 0 0
668k 4.8k 0 70M 668k 0 70M 0 0
667k 4.8k 0 70M 667k 0 70M 0 0
645k 4.5k 0 68M 645k 0 68M 0 0
686k 4.9k 0 72M 686k 0 72M 0 0
And by using just the cxl* interfaces we were getting about
input (Total) output
packets errs idrops bytes packets errs bytes colls drops
2.8M 0 1.2M 294M 1.6M 0 171M 0 0
2.8M 0 1.2M 294M 1.6M 0 171M 0 0
2.8M 0 1.2M 294M 1.6M 0 171M 0 0
2.8M 0 1.2M 295M 1.6M 0 172M 0 0
2.8M 0 1.2M 295M 1.6M 0 171M 0 0
These are our configurations for now. Any advice or suggestion will be
appreciated.
What I don't understand is that you have PAUSE disabled and congestion
drops enabled but still the number of packets coming in (whether they
are dropped eventually or not is irrelevant here) is very low in your
experiments. It's almost as if the senders are backing off in the face
of packet loss. Are you using TCP or UDP? Always use UDP for pps
testing -- the senders need to be relentless.
Regards,
Navdeep
/etc/rc.conf configurations
ifconfig_cxl0="up"
ifconfig_cxl1="up"
ifconfig_vcxl0="inet 172.16.2.1/24 -tso -lro mtu 9000"
ifconfig_vcxl1="inet 172.16.1.1/24 -tso -lro mtu 9000"
gateway_enable="YES"
/boot/loader.conf configurations
# Chelsio Modules
t4fw_cfg_load="YES"
t5fw_cfg_load="YES"
if_cxgbe_load="YES"
# rx and tx size
dev.cxl.0.qsize_txq=8192
dev.cxl.0.qsize_rxq=8192
dev.cxl.1.qsize_txq=8192
dev.cxl.1.qsize_rxq=8192
# drop toecaps to increase queues
dev.t5nex.0.toecaps=0
dev.t5nex.0.rdmacaps=0
dev.t5nex.0.iscsicaps=0
dev.t5nex.0.fcoecaps=0
# Controls the hardware response to congestion. -1 disables
# congestion feedback and is not recommended. 0 instructs the
# hardware to backpressure its pipeline on congestion. This
# usually results in the port emitting PAUSE frames. 1 instructs
# the hardware to drop frames destined for congested queues. From cxgbe
dev.t5nex.0.cong_drop=1
# Saw these recomendations in Vicenzo email thread
hw.cxgbe.num_vis=2
hw.cxgbe.fl_pktshift=0
hw.cxgbe.toecaps_allowed=0
hw.cxgbe.nnmtxq10g=8
hw.cxgbe.nnmrxq10g=8
/etc/sysctl.conf configurations
# Turning off pauses
dev.cxl.0.pause_settings=0
dev.cxl.1.pause_settings=0
# John Jasen suggestion - March 24, 2017
net.isr.bindthreads=0
net.isr.maxthreads=24
On 3/18/17 1:28 AM, Navdeep Parhar wrote:
On Fri, Mar 17, 2017 at 11:43:32PM -0400, John Jasen wrote:
On 03/17/2017 03:32 PM, Navdeep Parhar wrote:
On Fri, Mar 17, 2017 at 12:21 PM, John Jasen <jja...@gmail.com> wrote:
Yes.
We were hopeful, initially, to be able to achieve higher packet
forwarding rates through either netmap-fwd or due to enhancements based
off https://wiki.freebsd.org/ProjectsRoutingProposal
Have you tried netmap-fwd? I'd be interested in how that did in your tests.
We have. On this particular box, (11-STABLE, netmap-fwd fresh from git)
it took about 1.7m pps in, dropped 500k, and passed about 800k.
I'm lead to believe that vcxl interfaces may yield better results?
Yes, those are the ones with native netmap support. Any netmap based
application should use the vcxl interfaces. If you used them on the
main cxl interfaces you were running netmap in emulated mode.
Regards,
Navdeep
_______________________________________________
freebsd-net@freebsd.org mailing list
https://lists.freebsd.org/mailman/listinfo/freebsd-net
To unsubscribe, send any mail to "freebsd-net-unsubscr...@freebsd.org"
