Le 26 oct. 2012 à 23:40, Sami Halabi a écrit : > Hi, > did you try explicit "ifconfig ix0 up" instead of rebooting?
In fact, down, then up commands are necessary : ifconfig ix0 down ifconfig ix0 up Regards, Rémi > > Sami > > On Thu, Oct 25, 2012 at 4:29 PM, Rémi Pauchet <remi.pauc...@netasq.com> wrote: > more informations about the SR-IOV issue. > > The problem is that the link is not updated in the virtual machine (VF > driver). > > ie: I start the VM with my fiber unplugged, the vf link is "no carrier". > I plug the fiber, the link stays in state "no carrier". > If I reboot the vm, I get the active link. > I reproduce the issue with esxi 5.1 and xenserver 6 > > > On other hand, I still haven't managed to get an active link with VMWare > DirectPath. > > Regards, > Rémi > > > Le 17 oct. 2012 à 09:42, Rémi Pauchet a écrit : > > > Hi > > > > My interface is configured, UP and running and I still can't get a link > > > > Can you help me with this issue ? > > > > Regards, > > Rémi > > > > > > Le 12 oct. 2012 à 09:38, Rémi Pauchet a écrit : > > > >> Hi, > >> > >> Unfortunately not: > >> > >> ix0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 > >> > >> options=401bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,VLAN_HWTSO> > >> ether 00:e0:ed:1c:99:4e > >> inet 172.16.255.254 netmask 0xffff0000 broadcast 172.16.255.255 > >> inet6 fe80::2e0:edff:fe1c:994e%ix0 prefixlen 64 scopeid 0x2 > >> nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> > >> media: Ethernet autoselect > >> status: no carrier > >> ix1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 > >> > >> options=401bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,VLAN_HWTSO> > >> ether 00:e0:ed:1c:99:4f > >> inet 172.17.255.254 netmask 0xffff0000 broadcast 172.17.255.255 > >> inet6 fe80::2e0:edff:fe1c:994f%ix1 prefixlen 64 scopeid 0x3 > >> nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> > >> media: Ethernet autoselect > >> status: no carrier > >> > >> Regards, > >> Rémi > >> > >> Le 11 oct. 2012 à 18:25, Jack Vogel a écrit : > >> > >>> The ixgbe device will not get link until you have run init, so assign it > >>> an address or just do an ifconfig up. > >>> > >>> I have never used the driver using a passthru type setup but I believe > >>> its been done successfully if > >>> memory serves. > >>> > >>> Jack > >>> > >>> > >>> On Thu, Oct 11, 2012 at 8:39 AM, Rémi Pauchet <remi.pauc...@netasq.com> > >>> wrote: > >>> Hi, > >>> > >>> I'm trying to use the ixgbe (10Gb) driver in a FreeBSD virtual machine on > >>> an esxi 5 using DirectPath (PCI Passthrough) and the card is detected, > >>> but I can't get a link (status: no carrier) > >>> > >>> ix0: <Intel(R) PRO/10GbE PCI-Express Network Driver, Version - 2.3.11> > >>> mem 0xd2420000-0xd243ffff,0xd2400000-0xd2403fff irq 18 at device 0.0 on > >>> pci3 > >>> > >>> ix0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 > >>> > >>> options=401bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,VLAN_HWTSO> > >>> ether 00:e0:ed:1c:99:4e > >>> nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> > >>> media: Ethernet autoselect > >>> status: no carrier > >>> > >>> I have also tested with XenServer 6, using SR-IOV (ixgbevf driver) with > >>> the same result: the driver is loading, but no link detected. > >>> > >>> In both case (VMWare DirectPath and XenServer SR-IOV), I tested Linux > >>> with success. > >>> > >>> > >>> The card is an Intel 82599EB, the motherboard is an Intel X58 (supermicro > >>> X8ST3) with a Xeon W3680 and I've tested FreeBSD 8.3 and 9.0 > >>> > >>> I've found a forum thread with the same issue: > >>> http://forums.freebsd.org/showthread.php?t=29855 and no answer :) > >>> > >>> > >>> Please find in attachment the dmesg (boot -v) with the ix driver compiled > >>> with DEBUG flags using vmware. > >>> > >>> > >>> Can anyone provide feedback about this issue ? > >>> > >>> Regards, > >>> Rémi Pauchet > >>> > >>> > >>> > >> > > > > > > > -- > Sami Halabi > Information Systems Engineer > NMS Projects Expert > FreeBSD SysAdmin Expert >
