On Wed, Nov 07, 2007 at 10:32:04AM +0200, Alexander Shikoff wrote: > On Wed, Nov 07, 2007 at 04:51:34PM +0900, Pyun YongHyeon wrote: > > On Wed, Nov 07, 2007 at 09:37:08AM +0200, Alexander Shikoff wrote: > > > On Wed, Nov 07, 2007 at 09:24:30AM +0900, Pyun YongHyeon wrote: > > > > > > # pciconf -lv > > > > > > [...] > > > > > > [EMAIL PROTECTED]:3:0:0: class=0x020000 card=0xe0001458 > > chip=0x816810ec rev=0x01 hdr=0x00 > > > > > > vendor = 'Realtek Semiconductor' > > > > > > device = 'RTL8168/8111 PCI-E Gigabit Ethernet NIC' > > > > > > class = network > > > > > > subclass = ethernet > > > > > > [...] > > > > > > > > > > Further investigation... It seems that re(4) driver does not > > > > > support auto-negotiation correctly. If I manually set media to > > 100baseTX and > > > > > bring up interface with 'ifconfig re0 up' then it works. > > > > > > > > > > > > > Would you show me more information for link partner(i.e. FreeBSD 6.2 > > box)? > > > > > > Yes, of course: > > > > > > FreeBSD 6.2-STABLE 7.0-BETA2 > > > rl0 <===================> re0 > > > > > > rl0: <RealTek 8139 10/100BaseTX> port 0x9000-0x90ff mem > > 0xfa000000-0xfa0000ff irq 21 at device 1.0 on pci2 > > > miibus0: <MII bus> on rl0 > > > rl0: Ethernet address: 00:e0:7d:db:ca:98 > > > rl0: link state changed to UP > > > > > > # pciconf -lv > > > [EMAIL PROTECTED]:1:0: class=0x020000 card=0x813910ec chip=0x813910ec > > rev=0x10 hdr=0x00 > > > vendor = 'Realtek Semiconductor' > > > device = 'RT8139 (A/B/C/810x/813x/C+) Fast Ethernet Adapter' > > > class = network > > > subclass = ethernet > > > > > > > Hmm, the link partner uses rl(4) so show me the PHY driver(rlphy(4)?) > > information. (You can extract it from dmesg(8) output.) > rlphy0: <RealTek internal media interface> on miibus0 > rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > > > Does the link partner has a forced speed/duplex option for rl(4)? > No. > # ifconfig rl0 > rl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 > options=8<VLAN_MTU> > inet 10.0.34.1 netmask 0xffffff00 broadcast 10.0.34.255 > ether 00:e0:7d:db:ca:98 > media: Ethernet autoselect (100baseTX <full-duplex>) > status: active >
I couldn't see guilty code. In fact I couldn't reproduce it here. Since RTL8168/8111 has built-in crossover detection feature how about using straight cable? -- Regards, Pyun YongHyeon _______________________________________________ freebsd-net@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-net To unsubscribe, send any mail to "[EMAIL PROTECTED]"
