Jeremy Chadwick wrote:
On Thu, Aug 14, 2008 at 12:02:50PM +0400, sam wrote:
Jeremy Chadwick wrote:
On Thu, Aug 14, 2008 at 12:16:16AM -0700, Jeremy Chadwick wrote:
On Thu, Aug 14, 2008 at 10:57:53AM +0400, sam wrote:
Andrey V. Elsukov wrote:
sam wrote:
FreeBSD 7.0-STABLE FreeBSD 7.0-STABLE #5: Tue Aug 12 13:54:27
MSD 2008 root@:/usr/obj/usr/src/sys/GENERIC i386
|--------------------------------------------------------------------
please, any solution ?
Probably speed is limited via jumpers on your hard drive.
http://wdc.custhelp.com/cgi-bin/wdc.cfg/php/enduser/std_adp.php?p_faqid=1409&p_created=#jumper
tried it
without results
FWIW, the only time I've seen this happen is when there's a jumper
limiting the capability. You should have **removed** the OPT1 jumper,
and left any other jumpers alone.
If you're absolutely sure the jumper is removed, I'll purchase one of
these drives and test it on an ICH7 (Supermicro PDSMi+) to confirm your
findings.
Actually, I don't need to -- I'm using WD5000AAKS disks myself on
that exact system:
atapci1: <Intel AHCI controller> port
0x30e8-0x30ef,0x30dc-0x30df,0x30e0-0x30e7,0x30d8-0x30db,0x30b0-0x30bf mem
0xe8600400-0xe86007ff irq 19 at device 31.2 on pci0
atapci1: [ITHREAD]
atapci1: AHCI Version 01.10 controller with 4 ports detected
ata2: <ATA channel 0> on atapci1
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci1
ata3: [ITHREAD]
ata4: <ATA channel 2> on atapci1
ata4: [ITHREAD]
ata5: <ATA channel 3> on atapci1
ata5: [ITHREAD]
ad6: 476940MB <WDC WD5000AAKS-00YGA0 12.01C02> at ata3-master SATA300
ad8: 476940MB <WDC WD5000AAKS-00TMA0 12.01C01> at ata4-master SATA300
may issue in <Intel ICH7 SATA300 controller> driver ?
----------------------------------------------------
atapci1: <Intel ICH7 SATA300 controller> port
0xc880-0xc887,0xc800-0xc803,0xc480-0xc487,0xc400-0xc403,0xc080-0xc08f
irq 19 at device 31.2 on pci0
----------------------------------------------------
Possibly. All my Intel ICH7 boards have AHCI capability, and I use it.
See Chapter 4 here:
http://www.supermicro.com/manuals/motherboard/3000/MNL-0889.pdf
If your motherboard does, I'd recommend enabling it as well and see if
things change.
Regarding the "Enhanced" vs. "Compatible" mode: use Enhanced. On
my boards, choosing Enhanced makes the AHCI and Intel MatrixRAID
options appear.
I'm fairly certain you don't need AHCI to get SATA300, though.
I would recommend you re-check the jumpers on your disks to make sure
you didn't make a mistake when adjusting things.
- HDD on position: all jumpers removed;
- SATA controller in Enchanced mode;
- no option AHCI in BIOS
without results
/Vladimir Ermakov
_______________________________________________
freebsd-hackers@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-hackers
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
